Home › Engine / Hybrid System › 2AD-FTV ENGINE MECHANICAL › ENGINE UNIT
NM3090E _51 Engine / Hybrid System _008661 2AD-FTV ENGINE MECHANICAL _0048049 ENGINE UNIT GE GENERAL F

2AD-FTV ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2AD-FTV TOYOTA Direct injection 4 stroke common-rail Diesel engine (D-4D) is an in-line 4-cylinder, 2.2-liter, 16-valve DOHC turbocharged diesel engine with intercooler.


b.

This engine uses a direct injection system and common-rail system to achieve higher performance, clean emissions, low noise and low vibrations.


c.

This engine has 2 types; one type (models with DPF catalyst) uses both the Diesel Particulate Filter (DPF) catalyst and oxidation catalyst, and the other type (models without DPF catalyst) uses the oxidation catalyst only.



SPECIFICATION


No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain and Gear Drive
Combustion Chamber Direct Injection Type
Manifolds Cross-flow
Fuel System Common-rail Type
Displacement 2231 cm3 (136.1 cu. in.)
Bore x Stroke 86.0 mm x 96.0 mm (3.39 in. x 3.78 in.)
Compression Ratio 15.7 : 1
Max. Output [EEC] 110 kW @ 3600 rpm
Max. Torque [EEC] 340 N*m @ 2000 to 2800 rpm
Valve Timing Intake Open 2° BTDC
Closed 31° ABDC
Exhaust Open 51° BBDC
Closed 2° ATDC
Firing Order 1 - 3 - 4 - 2
Fuel Cetane Number 48 or higher
Emission Regulation EURO 4*2
EURO 5*3
Engine Service Mass (Reference)*1 195.2 kg (430.3 lb)*2
195.6 kg (431.2 lb)*3

*1: Weight shows the figure with oil and engine coolant fully filled.

*2: Models without DPF catalyst

*3: Models with DPF catalyst


W100162
5.021,0.781 5.635,1.094 0.615,0.313 10 (kW) 5.042,4.313 5.219,4.469 0.177,0.156 10 0 5.042,4.042 5.219,4.198 0.177,0.156 10 10 5.042,3.76 5.219,3.917 0.177,0.156 10 20 5.042,3.5 5.219,3.656 0.177,0.156 10 30 5.042,3.229 5.219,3.385 0.177,0.156 10 40 5.042,2.969 5.219,3.125 0.177,0.156 10 50 5.042,2.677 5.219,2.833 0.177,0.156 10 60 5.042,2.406 5.219,2.563 0.177,0.156 10 70 5.042,2.146 5.219,2.302 0.177,0.156 10 80 5.042,1.844 5.219,2 0.177,0.156 10 90 5.042,1.583 5.302,1.74 0.26,0.156 10 100 5.042,1.302 5.302,1.458 0.26,0.156 10 110 5.042,1.042 5.302,1.198 0.26,0.156 10 120 1.833,3.229 2.125,3.385 0.292,0.156 10 100 1.833,2.958 2.125,3.115 0.292,0.156 10 150 1.833,2.688 2.125,2.844 0.292,0.156 10 200 1.833,2.417 2.125,2.573 0.292,0.156 10 250 1.833,2.146 2.125,2.302 0.292,0.156 10 300 1.833,1.865 2.125,2.021 0.292,0.156 10 350 1.833,1.594 2.125,1.75 0.292,0.156 10 400 2.354,4.635 2.698,4.792 0.344,0.156 10 1000 2.875,4.635 3.219,4.792 0.344,0.156 10 2000 3.406,4.635 3.75,4.792 0.344,0.156 10 3000 3.917,4.646 4.26,4.802 0.344,0.156 10 4000 4.448,4.646 4.792,4.802 0.344,0.156 10 5000 1.813,1.333 2.479,1.656 0.667,0.323 10 (N*m) 1.125,2.708 1.771,3.042 0.646,0.333 10 Torque 5.531,2.719 6.26,3.073 0.729,0.354 10 Output 3.052,5.177 4.896,5.531 1.844,0.354 10 Engine Speed (rpm)


MAIN FEATURES


a.

The following performance features have been achieved for the 2AD-FTV engine through the use of the items listed below:

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and fuel economy

Item (1) (2) (3) (4) (5)
Engine Proper A cylinder head sub-assembly and cylinder block sub-assembly made of aluminum alloy are used. - - ○ - -
A piston provided with combustion chamber is used in conjunction with the use of direct injection. ○ - - - ○
Balance shafts which are directly driven by the crankshaft are used. - ○ - - -
Valve Mechanism A valve lash adjuster assembly is used. ○ ○ - ○ -
A timing chain and a No. 1 chain tensioner assembly are used. - ○ ○ ○ -
A valve rocker arm sub-assembly is used. ○ - - - ○
Lubrication System An oil filter with a replaceable element is used. - - - ○ -
A water-cooled type oil cooler assembly is used. ○ - - - -
Cooling System Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust System A DC motor type diesel throttle control motor is used in the diesel throttle body. For details on the throttle body, see the Intake Exhaust section.
[INTAKE SYSTEM > THROTTLE BODY(Click here)]
- - - - ○
A DC motor type EGR valve is used. For details on the EGR valve, see the Emission Control section.
[EMISSION CONTROL SYSTEM > EGR VALVE(Click here)]
- - - - ○
A water-cooled type EGR cooler that has a bypass is used. For details on the EGR cooler, see the Emission Control section.
[EMISSION CONTROL SYSTEM > EGR COOLER(Click here)]
- - - - ○
A variable nozzle vane type turbocharger sub-assembly is used. For details on the turbocharger, see the Intake/Exhaust section.
[INTAKE SYSTEM > TURBOCHARGER(Click here)]
○ - - - ○
The exhaust manifold converter uses an oxidation catalyst and Diesel Particulate Filter (DPF) catalyst.* For details on the catalyst converter, see the Emission Control section.
[EMISSION CONTROL SYSTEM > CATALYTIC CONVERTER(Click here)]
- - - - ○
Fuel System A common-rail type fuel injection system is used. For details on the common-rail system, see the Fuel section.
[FUEL SYSTEM > COMMON-RAIL SYSTEM(Click here)]
○ ○ - - ○
A piezo type injector assembly on which a compensation value and Quick Response (QR) code are printed is used. For details on the fuel injector, see the Fuel section.
[FUEL SYSTEM > FUEL INJECTOR(Click here)]
○ ○ - - ○
An exhaust fuel addition injector assembly is used.* For details on the exhaust fuel addition injector, see the Emission Control section.
[EMISSION CONTROL SYSTEM > EXHAUST FUEL ADDITION INJECTOR(Click here)]
- - - - ○
Serpentine Belt Drive System A serpentine belt drive system is used. - - ○ ○ -
Engine Control A pilot injection control system is used. ○ ○ - - ○
An oil maintenance management system is used. - - - ○ -
A vacuum pump with low friction is used. - - - - ○
A catalyst support control is used.* For details on the catalyst support control, see the Emission Control section.
[EMISSION CONTROL SYSTEM > CATALYST SUPPORT CONTROL(Click here)]
- - - - ○

*: Models with DPF catalyst


HINT:

○: Applicable

-: Not applicable