Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM
NM3090E _51 Engine / Hybrid System _008644 3ZR-FAE ENGINE CONTROL _0048051 SFI SYSTEM DE DETAILS F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  DETAILS  ACCELERATOR PEDAL SENSOR  


CONSTRUCTION


a.

Models with Continuously Variable Transaxle (CVT)

i.

The non-contact type accelerator pedal sensor assembly uses a Hall IC.


ii.

The magnetic yoke mounted at the base of the accelerator pedal arm moves around the Hall IC in accordance with the amount of effort applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal effort to the ECM.


iii.

This accelerator pedal sensor assembly includes 2 Hall ICs and circuits for the main and sub signals. Accelerator pedal sensor assembly converts the accelerator pedal depressed angles into electric signals with 2 differing characteristics and outputs them to the ECM.


iv.

When the depressing force applied to the accelerator pedal is greater than a predetermined amount, the ECM detects a "kick down on" from the VPA signal provided by the accelerator pedal sensor assembly.

W100338
0.573,5.219 0.635,5.219 0.635,5.219 0.771,5.729 true 1.354,5.667 1.167,5.667 1.167,5.667 1.01,5.854 true 2.24,0.5 2.042,0.5 2.042,0.5 1.719,1 true 1.104,1.031 1.24,1.031 1.24,1.031 1.438,1.385 true 0.844,2.375 1.063,2.375 1.063,2.375 1.458,2.948 false 2.323,2.271 1.865,2.271 true 1.208,6.115 1.26,6.323 1.26,6.323 1.365,6.323 true 1.115,7.156 1.344,7.354 1.344,7.354 1.458,7.354 false 6.344,1.927 5.646,0.688 5.646,0.688 6.031,0.688 true 5.979,2.115 5.135,0.646 5.135,0.646 4.781,0.646 true 4.198,5.823 4.354,6 0.156,0.177 10 0 2.292,0.427 2.823,0.802 0.531,0.375 10 Hall IC 0.104,0.948 1.094,1.26 0.99,0.313 10 Sensor Housing 0.073,2.313 0.854,2.927 0.781,0.615 10 Accelerator Pedal Arm 2.375,2.177 3.063,2.854 0.688,0.677 10 Magnetic Yoke 3.573,2.24 4.188,2.927 0.615,0.688 10 Output Voltage 4.927,1.885 5.333,2.115 0.406,0.229 10 VPA2 5.135,2.646 5.594,3.042 0.458,0.396 10 VPA 3.771,0.531 4.771,1.271 1,0.74 10 Output Voltage at Full Open 6.104,0.615 7.052,1.271 0.948,0.656 10 Kick Down Mode Voltage 4.052,1.385 4.354,1.792 0.302,0.406 10 (V) 4.229,3.219 4.375,3.563 0.146,0.344 10 0 4.052,3.792 4.333,4.094 0.281,0.302 10 (N) 3.583,4.417 4.385,5.052 0.802,0.635 10 Depressing Force 4.406,6.208 6.635,6.594 2.229,0.385 10 Accelerator Pedal Depressed Angle 2.938,5.5 3.5,5.906 0.563,0.406 10 ECM 0.104,5.146 0.583,5.448 0.479,0.302 10 Hall IC 1.396,5.594 1.906,6.01 0.51,0.417 10 Hall IC 1.427,6.219 2.094,6.875 0.667,0.656 10 Magnetic Yoke 1.521,7.292 3.01,7.625 1.49,0.333 10 Accelerator Pedal Arm 3.135,4.865 3.458,5.01 0.323,0.146 10 VPA 2.802,4.865 3.115,5.021 0.313,0.156 10 EPA 2.313,4.875 2.719,5.042 0.406,0.167 10 VCPA 2.313,6.281 2.698,6.5 0.385,0.219 10 VPA2 2.26,6.594 2.646,6.833 0.385,0.24 10 EPA2 2.26,6.896 2.667,7.156 0.406,0.26 10 VCP2



b.

Models with Manual Transaxle

i.

The non-contact type accelerator pedal sensor assembly uses a Hall IC.


ii.

The magnetic yoke mounted at the accelerator pedal arm rotates around the Hall IC in accordance with the amount of effort applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux into electrical signals, and outputs them as accelerator pedal effort to the ECM.


iii.

The Hall IC contains circuits for the main and sub signals. The Hall IC converts the accelerator pedal depressed angles into electric signals with 2 differing characteristics and outputs them to the ECM.

W100142E24
1.167,1.948 1.635,0.604 1.635,0.604 1.917,0.604 true 2.229,2.583 1.938,3.313 1.938,3.313 1.604,3.313 true 4.552,1.115 4.469,0.583 4.469,0.583 4.25,0.583 true 4.438,1.583 3.698,1.333 3.698,1.333 3.5,1.333 true 4.427,2.063 3.688,2.313 3.688,2.313 3.49,2.313 true 2.052,2.052 1.49,2.906 1.49,2.906 1.323,2.906 true 4.625,2.667 4.75,2.938 4.75,2.938 4.583,2.938 true 3.333,3.292 5.604,3.74 2.271,0.448 10 false Accelerator Pedal Sensor Assembly 3.063,1.26 3.542,1.615 0.479,0.354 10 false Hall IC 3.76,0.5 4.302,0.896 0.542,0.396 10 false Magnet 3.031,2.229 3.51,2.583 0.479,0.354 10 false Hall IC 1.167,4.052 1.458,4.458 0.292,0.406 10 false (V) 1.49,4.302 1.615,4.635 0.125,0.333 10 false 5 0.833,5.344 1.417,6.063 0.583,0.719 10 false Output Voltage 1.5,6.01 1.625,6.302 0.125,0.292 10 false 0 0.813,6.385 1.667,6.74 0.854,0.354 10 false Fully Closed 5.167,6.365 5.917,6.698 0.75,0.333 10 false Fully Open 2.302,6.365 4.479,6.667 2.177,0.302 10 false Accelerator Pedal Position (Angle) 5.656,1.031 6.052,1.323 0.396,0.292 10 false VPA 5.656,1.375 6.052,1.667 0.396,0.292 10 false EPA 5.573,1.75 5.969,2.042 0.396,0.292 10 false VCPA 5.583,2.031 5.979,2.323 0.396,0.292 10 false VPA2 5.594,2.375 6.01,2.667 0.417,0.292 10 false EPA2 5.573,2.75 5.969,3.042 0.396,0.292 10 false VCP2 1.969,0.531 2.448,0.885 0.479,0.354 10 false Hall IC 3.667,5.417 4.063,5.708 0.396,0.292 10 false VPA1 2.49,5 2.885,5.292 0.396,0.292 10 false VPA2 6.281,1.885 6.656,2.198 0.375,0.313 10 false ECM 0.188,3.219 1.625,3.521 1.438,0.302 10 false Accelerator Pedal Arm 0.375,2.813 1.406,3.177 1.031,0.365 10 false Magnetic Yoke 3.635,2.865 4.667,3.229 1.031,0.365 10 false Magnetic Yoke