Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE UNIT
NM3090E _51 Engine / Hybrid System _008637 3ZR-FE ENGINE MECHANICAL _0048055 ENGINE UNIT DE DETAILS F

3ZR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CRANKSHAFT AND BEARING  


CONSTRUCTION


a.

The crankshaft has 5 journals and 8 balance weights.


b.

The pins and journals have been machined with increased precision and the surface roughness has been minimized to reduce friction.


c.

All pins and journal fillets have been hardened to improve their strength.

W100301
1.99,1.573 1.719,1.833 1.719,1.833 1.625,1.833 true 2.865,1.167 2.667,0.365 2.667,0.365 2.573,0.365 true 4.76,0.76 4.719,0.375 4.719,0.375 4.604,0.375 true 5.167,1.177 5.271,0.719 5.271,0.719 5.427,0.719 true 3.885,2.042 4.125,2.51 4.125,2.51 4.375,2.51 true 2.177,1.958 2.177,2.344 2.177,2.344 2.229,2.344 true 2.385,0.281 2.542,0.438 0.156,0.156 10 *a 4.438,0.302 4.625,0.448 0.188,0.146 10 *b 5.469,0.646 5.646,0.802 0.177,0.156 10 *3 1.458,1.792 1.615,1.969 0.156,0.177 10 *1 2.26,2.271 2.427,2.427 0.167,0.156 10 *2 4.438,2.448 4.615,2.594 0.177,0.146 10 *c
*1 No. 1 Journal *2 Balance Weight
*3 No. 5 Journal - -
*a Journal Fillet *b Oil Hole
*c Pin Fillet - -



d.

The crankshaft bearings have been optimized in width to reduce friction.


e.

An oil groove is provided on each crankshaft bearing (upper main bearing). The oil groove is deep at the center and is shallow at the edges to reduce the amount of oil that leaks from the crankshaft bearing. As a result, the size of the oil pump is reduced, minimizing friction.


f.

The lining surface of the crankshaft bearing has been micro-grooved to provide an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibrations have been reduced.

W100458
4.302,0.427 6.854,2.906 2.552,2.479 3.625,1.135 3.688,0.75 3.688,0.75 3.875,0.75 true 2.917,3.156 3.125,3.156 3.125,3.156 3.25,2.854 true 1.531,1.99 1.375,1.448 1.375,1.448 1.177,1.448 true 2.948,1.448 2.479,0.781 2.479,0.781 2.177,0.781 true 3.958,0.677 4.271,0.833 0.313,0.156 10 *1 2.729,3.094 3.042,3.25 0.313,0.156 10 *2 0.969,1.354 1.281,1.51 0.313,0.156 10 *a 5.448,1.49 5.76,1.646 0.313,0.156 10 *d 4.927,1.813 5.24,1.969 0.313,0.156 10 *c 4.354,0.49 4.667,0.646 0.313,0.156 10 *e 5.979,1.802 6.292,1.958 0.313,0.156 10 *c 1.969,0.698 2.281,0.854 0.313,0.156 10 *b
*1 Upper Main Bearing *2 Lower Main Bearing
*a Micro-grooved *b Oil Groove
*c Edge *d Center
*e Oil Groove Depth - -