Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE SYSTEM › 2012.12–2015.10
NM3090E _52 Drivetrain _008829 EA64F MANUAL TRANSMISSION / TRANSAXLE _0050347 MANUAL TRANSAXLE SYSTEM CO CONTROL F

EA64F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  CONTROL  GEAR SHIFT INDICATOR SYSTEM  


FUNCTION


a.

In Gear Shift Indicator system, the ECM calculates an environmentally favorable shift position based on the vehicle conditions, and makes a request to the meter ECU to indicate upshifting or downshifting. Then, Gear Shift Indicator in the combination meter gives a shifting recommendation to the driver.


b.

The ECM determines the actual gear position based on the signals from the crank position sensor and speed sensors, and the target gear position based on the signals from the accelerator pedal position sensor and speed sensors.


c.

By driving in accordance with the shift change recommendations indicated by Gear Shift Indicator, the driver can enhance environmental performance, improve fuel economy and reduce exhaust gas output within the limits of engine performance.

X111776
0.76,0.448 2.563,0.74 1.802,0.292 10 Crankshaft Position Sensor 0.552,1.188 2.74,1.458 2.188,0.271 10 Accelerator Pedal Position Sensor 0.708,1.938 2.604,2.229 1.896,0.292 10 Stop Light Switch Assembly 0.635,2.698 2.656,2.979 2.021,0.281 10 Back-up Light Switch Assembly 0.823,3.448 2.625,3.76 1.802,0.313 10 Clutch Switch Assembly 3.396,1.885 3.875,2.24 0.479,0.354 10 ECM 5.292,0.438 6.344,0.729 1.052,0.292 10 Speed Sensors 5.24,1.333 6.427,1.583 1.188,0.25 10 Skid Control ECU 5.396,2.271 6.271,2.521 0.875,0.25 10 Meter ECU 5.188,3.969 6.49,4.26 1.302,0.292 10 Gear Shift Indicator 4.74,4.479 5.76,4.802 1.021,0.323 10 : CAN (V bus)

Control of Gear Shift Indicator System
Control Outline
System Start Checks the bulb of the indicator lights from the time the ignition switch is turned to ON until the engine is started.
Shifting Recommendation Control Calculates an environmentally favorable shift position based on the driving conditions of the vehicle, and gives a shifting recommendation.
Shift Control in Uphill Traveling Prevents unnecessary shifting instructions by estimating the gradient of the road based on the driving conditions, and provides shift position instructions that enable the vehicle to attain the proper drive force.
Delta Throttle Acceleration Control Detects a deceleration request when the driver releases the accelerator pedal suddenly. Thus, this control will not provide an upshift instruction. However, it will provide an upshift recommendation to protect the engine if the engine speed is high.


d.

Gear Shift Indicator system will not perform control while the vehicle is being driven in reverse.


e.

Gear Shift Indicator system will not perform control while the vehicle is stopped or the clutch is not engaged while shifting.


f.

Upon receiving a shift instruction request from the ECM, the meter ECU will illuminate the indicator light.


g.

The 2 indicator lights illuminate simultaneously during a bulb check.

X111771E01
1.573,1.083 1.875,1.083 true 1.573,1.698 1.875,1.698 true 0.948,2.188 2.25,2.49 1.302,0.302 10 false Gear Shift Indicator 3.052,0.615 4.365,0.917 1.313,0.302 10 false Illumination Location 4.823,0.615 6.333,0.917 1.51,0.302 10 false Instruction Description 3.594,1.052 3.906,1.354 0.313,0.302 10 false A 3.594,1.479 3.906,1.781 0.313,0.302 10 false B 3.396,1.885 4.125,2.135 0.729,0.25 10 false A and B 4.74,1.052 6.438,1.333 1.698,0.281 10 false Shift-up Recommendation 4.708,1.479 6.563,1.729 1.854,0.25 10 false Shift-down Recommendation 5.188,1.885 6.094,2.188 0.906,0.302 10 false Bulb Check 1.927,1 2.24,1.302 0.313,0.302 10 false A 1.927,1.615 2.24,1.917 0.313,0.302 10 false B