Home › Drivetrain › AXLE AND DIFFERENTIAL › AXLE SYSTEM
NM3090E _52 Drivetrain _008814 AXLE AND DIFFERENTIAL _0050351 AXLE SYSTEM GE GENERAL F

AXLE AND DIFFERENTIAL  AXLE SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Front Axle

i.

Compact and highly rigid double-row angular ball bearings are used. The double-row angular ball bearings and the axle hub are integrated to ensure high rigidity, thus achieving excellent driving stability and braking stability.


ii.

The speed sensor rotor is integrated in the bearing inner race.


iii.

A 12-point lock nut is used and staked in order to ensure that the axle hub is properly tightened. Once removed, this nut cannot be reused.

X111821
1.979,1.583 0.75,1.083 true 1.896,2.229 0.75,2.667 true 5.479,1.583 4.25,1.083 true 5.396,2.219 4.25,2.667 true 3.083,1.333 2.385,1.615 true 3.083,2.417 2.531,2 true 6.583,2.417 6.042,2 true 6.583,1.333 5.896,1.594 true 0.292,0.219 0.615,0.479 0.323,0.26 12 *A: 3.781,0.219 4.094,0.469 0.313,0.25 12 *B: 0.573,0.979 0.885,1.135 0.313,0.156 10 *1 0.583,2.594 0.896,2.75 0.313,0.156 10 *2 3.135,2.365 3.448,2.521 0.313,0.156 10 *3 3.135,1.219 3.448,1.375 0.313,0.156 10 *4 4.073,0.979 4.385,1.135 0.313,0.156 10 *1 4.083,2.594 4.396,2.75 0.313,0.156 10 *2 6.635,2.354 6.948,2.51 0.313,0.156 10 *3 6.635,1.229 6.948,1.385 0.313,0.156 10 *4
*A Models with 15/16 inch Disc Brake *B Models with 17 inch Disc Brake
*1 Double-row Angular Ball Bearing *2 Speed Sensor Rotor
*3 Lock Nut (12-point) *4 Front Axle Hub


NOTICE:
·

Do not place magnetized objects close to the surface of the sensor rotor.

·

Do not allow any iron particles, iron sand, dust, debris or oil to come in contact with the surface of the sensor rotor.





b.

Rear Axle

i.

Compact and highly rigid double-row angular ball bearings are used. The double-row angular ball bearings and the axle hub are integrated to ensure high rigidity, thus achieving excellent driving stability and braking stability.


ii.

The speed sensor rotor is integrated in the bearing inner race.


iii.

A 12-point lock nut is used on the 4WD/AWD models and staked in order to ensure that the axle hub is properly tightened. Once removed, this nut cannot be reused.

X111822
1.948,1.583 2.667,1.167 true 2.167,2.167 2.667,2.5 true 1.448,2.125 0.75,2.5 true 1.115,1.688 0.75,1.333 true 5.521,1.531 6.25,1.167 true 5.75,2.167 6.25,2.5 true 5.083,2.198 4.417,2.583 true 6.25,2.167 5.917,2 true 0.292,0.24 0.604,0.49 0.313,0.25 12 *A: 3.802,0.24 4.104,0.479 0.302,0.24 12 *B: 0.583,1.208 0.896,1.365 0.313,0.156 10 *1 0.583,2.448 0.896,2.604 0.313,0.156 10 *2 2.719,2.448 3.031,2.604 0.313,0.156 10 *3 2.708,1.063 3.021,1.219 0.313,0.156 10 *4 6.313,2.115 6.625,2.271 0.313,0.156 10 *5 4.25,2.531 4.563,2.688 0.313,0.156 10 *2 6.292,1.073 6.604,1.229 0.313,0.156 10 *4 6.313,2.458 6.625,2.615 0.313,0.156 10 *3
*A 2WD Models *B 4WD/AWD Models
*1 Speed Sensor *2 Speed Sensor Rotor
*3 Rear Axle Hub *4 Double-row Angular Ball Bearing
*5 Lock Nut (12-point) - -


NOTICE:
·

Do not place magnetized objects close to the surface of the sensor rotor.

·

Do not allow any iron particles, iron sand, dust, debris or oil to come in contact with the surface of the sensor rotor.