Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM › 2012.12–2015.04
NM3090E _57 Power Source / Network _008901 NETWORKING _0058430 MULTIPLEX COMMUNICATION SYSTEM GE GENERAL F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The multiplex communication system uses the following 2 communication protocols:

i.

The Controller Area Network (CAN) is used for communication between the engine, chassis and body electrical system.


ii.

The Local Interconnect Network (LIN) is used for communication within the body electrical system.



b.

The CAN has 2 types, with different communication speeds: the HS-CAN (high speed) and the MS-CAN (medium speed).


c.

The main body ECU is used as a gateway to transmit data between the buses.



MAIN FEATURES


a.

Multiplex communication uses serial communication data that consists of bits and frames in order to exchange information between the various ECUs. This allows a reduction of the amount of wiring used in the vehicle.

i.

A bit is the basic unit of communication used to represent the information. A bit is represented by binary values of "0" or "1".


ii.

A frame is a body of data transmitted together. A frame contains a header that indicates the beginning, and an end message that indicates the end.

Y100473E02
0.115,0.104 1.781,0.469 1.667,0.365 10 Conceptual Drawing 3.833,0.833 4.385,1.198 0.552,0.365 10 Data 3.844,1.979 4.458,2.302 0.615,0.323 10 Frame 0.74,3.427 1.24,3.802 0.5,0.375 10 Battery 2.073,4.281 2.688,4.646 0.615,0.365 10 Switch 2.135,1.115 2.281,1.375 0.146,0.26 10 0 3.313,2.885 3.698,3.146 0.385,0.26 10 On 3.302,3.271 3.542,3.531 0.24,0.26 10 Off 2.771,3.406 3.167,3.792 0.396,0.385 10 ECU 4.823,3.396 5.219,3.719 0.396,0.323 10 ECU 2.135,0.677 2.458,0.938 0.323,0.26 10 1 5.125,1.385 6.26,1.688 1.135,0.302 10 End Message 2.573,1.406 3.542,1.708 0.969,0.302 10 Header 6.5,4.01 7.063,4.333 0.563,0.323 10 Solenoid 6.51,3.604 7.0,3.865 0.49,0.26 10 Heater 6.51,3.188 7.01,3.469 0.5,0.281 10 Motor 6.521,2.75 6.948,3.042 0.427,0.292 10 Light 0.094,0.885 1.979,1.25 1.885,0.365 10 Serial Communication Data



b.

Differences between CAN and LIN

i.

The protocols, which are the rules for establishing data communication, differ between CAN and LIN. If the ECUs in the networks use different data frameworks such as communication speed, communication wire or signals, they will be unable to understand each other. Therefore, protocols (rules) must be established among them.


ii.

Compared to LIN, CAN features high-speed data transmission. Therefore, CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately for the powertrain and chassis control systems. These systems require large amounts of data to be transmitted in short periods of time.

Protocol CAN LIN
HS-CAN MS-CAN
Communication Speed 500 kbps* 250 kbps* 9.6 kbps* (Max. 20 kbps*)
Communication Wire Twisted-pair Wire AV Single Wire
Drive Type Differential Voltage Drive Single Wire Voltage Drive
Data Length 1-8 Bytes (Variable) 2, 4, 8 Bytes (Variable)

HINT:

*: bps is an abbreviation of "Bits Per Second", indicating the number of bits that can be transmitted per second.




c.

Communication Wire

i.

A twisted pair of wires is used for CAN communication. A single Automobile Vinyl (AV) wire is used for LIN communication.

Communication Wire Outline
Twisted-pair Wire
Y120656

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.
AV Single Wire
Y120657

This is a lightweight single communication wire that consists of a single core line surrounded by insulation. Voltage is applied to this line in order to drive communication, and this system is called a "Single Wire Voltage Drive".

Y104667E02
1.396,1.417 2.542,1.719 1.146,0.302 10 false AV Single Wire 4.698,1.51 6.021,1.813 1.323,0.302 10 false Twisted-pair Wire 1.104,2.146 2.958,2.448 1.854,0.302 10 false Single Wire Voltage Drive 4.51,2.146 6.406,2.448 1.896,0.302 10 false Differential Voltage Drive 0.75,1.313 1.24,1.615 0.49,0.302 10 false ECU 2.729,1.313 3.26,1.615 0.531,0.302 10 false ECU 4.052,1.313 4.573,1.615 0.521,0.302 10 false ECU 6.146,1.313 6.635,1.615 0.49,0.302 10 false ECU




PRECAUTION


a.

The type of door control receiver used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section:

Vehicle Specification Part Name in Manual Actual Part Name
Models with Tire Pressure Warning System Integrated Door Control Receiver and Tire Pressure Warning ECU and Receiver Door Control Receiver Door Control and Tire Pressure Monitoring System Receiver Assembly
Separate Door Control Receiver and Tire Pressure Warning ECU and Receiver Door Control Receiver Door Control Receiver
Models without Tire Pressure Warning System Door Control Receiver Door Control Receiver