Home › Engine / Hybrid System › 1AD-FTV STOP AND START › STOP AND START SYSTEM › 2012.12–2015.10
NM3090E _51 Engine / Hybrid System _008900 1AD-FTV STOP AND START _0058435 STOP AND START SYSTEM GE GENERAL F

1AD-FTV STOP AND START  STOP AND START SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

To achieve low emissions and enhanced fuel economy, the stop and start system has been developed.


b.

The stop and start system automatically stops the engine when the vehicle comes to a stop, such as when the vehicle stops at a red traffic light. When starting off, the engine is automatically restarted by simply depressing the clutch pedal, without requiring extra activity from the driver.

Y127764E01
1.427,0.708 2.219,1.052 0.792,0.344 10 false Deceleration 2.521,0.719 3.375,1.063 0.854,0.344 10 false Vehicle Stop 3.708,0.708 4.563,1.052 0.854,0.344 10 false Idling Stop 4.688,0.708 5.677,1.073 0.99,0.365 10 false Engine Restart 5.885,0.719 6.781,1.063 0.896,0.344 10 false Acceleration 1.604,2.021 2.5,2.365 0.896,0.344 10 false Depressed 2.083,2.792 2.979,3.135 0.896,0.344 10 false Depressed 4.76,2.823 5.656,3.167 0.896,0.344 10 false Depressed 4.792,1.75 5.438,2.177 0.646,0.427 10 false Released 4.948,2.521 5.594,2.948 0.646,0.427 10 false Released 2.635,2.5 3.281,2.927 0.646,0.427 10 false Released 2.417,3.292 3.313,3.635 0.896,0.344 10 false Neutral 5.76,3.302 6.5,3.823 0.74,0.521 10 false Moved from Neutral 0.385,1.927 1.281,2.271 0.896,0.344 10 false Brake Pedal 0.385,2.719 1.281,3.063 0.896,0.344 10 false Clutch Pedal 0.385,3.51 1.281,3.854 0.896,0.344 10 false Shift Lever


c.

The stop and start system consists of an engine stop and start ECU with a built-in backup boost converter and a permanently engaged starter assembly.


d.

Based on signals from various sensors, switch, and the ECM, the engine stop and start ECU controls the stopping and starting of the engine.


e.

To allow management of the life span of the starter assembly, the engine stop and start ECU counts the number of times the starter operates. If the number exceeds a threshold, the ECU blinks the stop and start cancel indicator light to inform the driver of recommended replacement timing.

HINT:

After the starter assembly has been replaced, it is necessary to clear the record of the number of times that the starter assembly has been operated. For details, refer to the Repair Manual.


W111406E02
1.073,1.677 2.01,2.5 0.938,0.823 1.083,0.813 1.99,1.198 0.906,0.385 10 Engine Stop and Start ECU 1.094,1.719 2.042,2.188 0.948,0.469 10 Backup Boost Converter 5.417,1.083 5.958,1.323 0.542,0.24 10 Battery 3.125,2.219 4.417,2.521 1.292,0.302 10 Generator Assembly 3.406,2.708 4.323,2.906 0.917,0.198 10 Engine 3.333,3.156 4.5,3.573 1.167,0.417 10 Starter Assembly 5.146,3.292 5.927,3.844 0.781,0.552 10 Combination Meter Assembly 3.135,4.177 4.823,4.375 1.688,0.198 10 CAN (V Bus) 1.354,3.802 1.813,4 0.458,0.198 10 ECM



PRECAUTION


a.

Ignition Switch Expressions

i.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch
(Position)
Engine Switch
(Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)