Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.10–2015.10
NM3090E _58 Vehicle Interior _009125 METER / GAUGE / DISPLAY _0050691 METER / GAUGE SYSTEM CO CONTROL F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  CONTROL  COMBINATION METER  


SYSTEM CONTROL


a.

Operating Condition

i.

Eco Driving Indicator

·

Eco Driving Indicator starts to operate when all of the following conditions are met:

Condition Ignition switch is ON.
Engine is running.
Shift lever is in D.
Drive mode is Normal or ECO mode.

·

Eco Driving Indicator stops operation when any of the following conditions is met:

Condition Ignition switch is off.
Engine is stopped.
Shift lever is in any position other than D.
Drive mode is any other mode except Normal or ECO mode.





FUNCTION


a.

Buzzer Function

i.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:

Item
·

Front Seat Belt Warning

·

EPS Warning

·

Entry and Start System Warning

·

Immobiliser System

·

Multi-information Display Warning Mode Indication

·

Speed Warning

·

Parking Brake Unreleased Warning

·

Door Open Driving Warning

·

Downshift Reject Warning

·

Light Reminder

·

Sliding Roof Open Warning

·

Hill-start Assist Control

·

Rear Seat Belt Warning

·

Key Reminder

·

Engine Stop and Start Warning

·

Brake Buzzer



HINT:

The buzzer function differs by vehicle specification.




b.

Multi-information Display

i.

The multi-information display can be switched by operating the DISP switch located on the steering pad switch assembly.


ii.

The multi-information display indicates as follows:

Display Outline*1
Cruise Information In the cruise information display, 9 types of information can be displayed:
·

Current Fuel Consumption

·

Average Fuel Consumption

·

Average Vehicle Speed

·

Elapsed Time*2

·

Cruising Range

·

Outside Temperature

·

ECO ODO*2

·

ECO Time*2

·

ECO Driving Indicator Zone Display*3


Water Temperature Gauge The engine coolant temperature date are displayed with bar graph.
Warning*2 If necessary, the warning display and advisory display will interrupt the multi-information display immediately.
Customization*2 The language, units, Eco Driving Indicator Light can be set up from this screen. The customization display is available only while the vehicle is stopped. If vehicle movement is detected during setup, the setup will be canceled automatically.

HINT:

*1: The items displayed differ by vehicle specification.

*2: Models with dot display type multi-information display

*3: When the ECO driving indicator zone display is selected by customization function.



iii.

The multi-information display undergoes the following transitions:

Y129601E01
0.198,0.198 1.417,0.573 1.219,0.375 10 false Ignition Switch Off 3.313,0.281 4.094,0.656 0.781,0.375 10 false Display Off 5.521,0.281 6.635,0.635 1.115,0.354 10 false Warning Display 4.74,0.281 4.99,0.604 0.25,0.323 10 false 1 4.75,0.625 5,0.948 0.25,0.323 10 false 2 3.729,1.031 3.979,1.354 0.25,0.323 10 false 3 3.177,1.573 4.292,1.927 1.115,0.354 10 false Opening Display 5.073,1.583 6.646,1.938 1.573,0.354 10 false Oil Maintenance Display 4.573,1.365 4.823,1.688 0.25,0.323 10 false 1 5.906,1.958 6.156,2.281 0.25,0.323 10 false 2 5.458,2.469 6.51,3.073 1.052,0.604 10 false Lane Departure Warning Display 4.771,2.729 5.021,3.052 0.25,0.323 10 false 1 4.792,3.094 5.042,3.417 0.25,0.323 10 false 2 3.115,3.438 4.24,4.104 1.125,0.667 10 false Cruise Information Display 0.198,1.354 1.771,1.708 1.573,0.354 10 false Ignition Switch On 0.688,3.615 1.802,3.969 1.115,0.354 10 false DTC Display 2.24,3.646 2.49,3.969 0.25,0.323 10 false 1 2.25,3.969 2.5,4.292 0.25,0.323 10 false 2 5.281,4.031 6.729,4.375 1.448,0.344 10 false Customization Display 4.771,4.063 5.021,4.385 0.25,0.323 10 false 1 4.781,4.375 5.031,4.698 0.25,0.323 10 false 2 5.438,5.01 6.552,5.365 1.115,0.354 10 false Warning Display 4.781,5.021 5.031,5.344 0.25,0.323 10 false 1 4.792,5.333 5.042,5.656 0.25,0.323 10 false 2 3.729,6.01 3.979,6.333 0.25,0.323 10 false 4 0.208,6.323 1.458,6.708 1.25,0.385 10 false Ignition Switch Off 3.344,6.813 4.146,7.146 0.802,0.333 10 false Display Off 5.521,6.802 6.635,7.156 1.115,0.354 10 false Warning Display 4.76,6.542 5.01,6.865 0.25,0.323 10 false 1 4.771,6.979 5.021,7.302 0.25,0.323 10 false 2

No. Condition
1 Conditions are met.
2 Conditions are not met.
3 Ignition switch is turned ON.
4 Ignition switch is turned off.


iv.

Cruise Information Display and ODO/TRIP Display (Models with Dot Display Type Multi-information Display)

·

The cruise information display can be switched by operating the DISP switch. The counter can be reset by pressing and holding the DISP switch for 0.8 seconds or more.

·

The ODO/TRIP meter display can be switched by operating the ODO/TRIP switch.


Y129602E01
2.135,0.219 2.292,0.417 0.156,0.198 10 1 0.76,1.906 0.917,2.104 0.156,0.198 10 1 2.115,1.865 2.271,2.063 0.156,0.198 10 2 3.677,1.083 4.156,1.375 0.479,0.292 10 b, 1 4.615,0.052 5.094,0.344 0.479,0.292 10 a, 1 5.125,1.292 5.281,1.49 0.156,0.198 10 2 6.219,1.021 6.698,1.313 0.479,0.292 10 a, 1 4.615,1.677 5.094,1.969 0.479,0.292 10 b, 1 6.219,2.469 6.375,2.667 0.156,0.198 10 1 2.958,3.292 4.188,3.667 1.229,0.375 10 Customize Display 4.677,3.292 4.833,3.49 0.156,0.198 10 2 2.146,3.115 2.302,3.313 0.156,0.198 10 3 0.771,4.083 0.927,4.281 0.156,0.198 10 1 2.323,4.583 2.479,4.781 0.156,0.198 10 1 4.885,4.594 5.042,4.792 0.156,0.198 10 1 6.219,3.906 6.375,4.104 0.156,0.198 10 1 0.958,5.615 1.115,5.802 0.156,0.188 10 2

No. Condition
a Standard display mode
b Eco display mode
1 The DISP switch is operated for less than 0.8 seconds.
2 The DISP switch is operated for 0.8 seconds or more to reset.
3 The DISP switch is operated for 0.8 seconds or more to customize mode display.

Display Outline
Current Fuel Consumption
Y129620

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN), provided that the ignition switch is turned ON.
Total Average Fuel Consumption
Y129621

·

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN) since the counter was reset.

·

The display updates every 10 seconds.


Average Vehicle Speed
Y129622

·

Displays the value that has been calculated by the meter ECU, which is based on the elapsed time and driven distance since the ignition switch was turned ON or since the counter was reset.

·

The display updates every 10 seconds.


Elapsed Time
Y129623

Displays the time that has elapsed since the ignition switch was turned ON or since the counter was reset.
Cruising Range
Y129624

Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch is turned ON.
Outside Temperature
Y129625

·

Displays the outside temperature.

·

The display updates every second.


ECO ODO
Y129626

Displays the total amount of engine stoppage time occurring since the last reset.
ECO Time
Y129627

Displays the total amount of engine stoppage time occurring since the ignition switch was last turned ON.
Total Average Fuel Consumption
Y129628

·

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN) since the counter was reset.

·

The display updates every 10 seconds.


ECO Driving Indicator Zone Display Eco driving ratio based on acceleration is shown with a bar graph.

Y129646N01
2.198,1.854 2.354,2.052 0.156,0.198 10 3 3.063,1.385 3.219,1.583 0.156,0.198 10 1 4.323,0.396 4.479,0.594 0.156,0.198 10 1 4.51,1.833 4.667,2.031 0.156,0.198 10 1 5.75,1.198 5.906,1.396 0.156,0.198 10 1 6.865,0.552 7.021,0.75 0.156,0.198 10 2 6.865,2.052 7.021,2.25 0.156,0.198 10 2

No. Condition
1 The ODO/TRIP switch is operated for less than 0.8 seconds.
2 The ODO/TRIP switch is operated for 0.8 seconds or more to reset.
3 The ODO/TRIP switch is operated for 0.8 seconds or more to change the dimming level.

Display Outline
Odometer Display
Y129647

Displays the odometer.
Trip Meter A Display
Y129648

Displays the trip meter A.
Trip Meter B Display
Y129649

Displays the trip meter B.
Dimming Mode Display
Y129650

Displays the combination meter brightness level.


v.

Cruise Information Display (Models with Segment Display Type Multi-information Display)

The cruise information display can be switched by operating the DISP switch. The counter can be reset by pressing and holding the DISP switch for 0.8 seconds or more.


Y129603N01
0.781,1.719 0.938,1.917 0.156,0.198 10 false 1 0.771,3.354 0.927,3.552 0.156,0.198 10 false 1 2.323,3.885 2.479,4.083 0.156,0.198 10 false 1 3.854,3.167 4.333,3.385 0.479,0.219 10 false b, 1 4.729,3.917 5.208,4.135 0.479,0.219 10 false a, 1 6.063,3.156 6.542,3.375 0.479,0.219 10 false a, 1 6.302,1.521 6.458,1.719 0.156,0.198 10 false 1 2.156,0.625 2.313,0.823 0.156,0.198 10 false 1 4.625,0.635 4.781,0.833 0.156,0.198 10 false 1 3.583,1.51 3.74,1.708 0.156,0.198 10 false 2 3.281,3.156 3.438,3.354 0.156,0.198 10 false 2 5.833,1.5 5.99,1.698 0.156,0.198 10 false 2 6.208,4.813 6.365,5.01 0.156,0.198 10 false 2 4.729,2.26 5.208,2.479 0.479,0.219 10 false b, 1

No. Condition
a Standard display mode
b Eco display mode
1 The DISP switch is operated for less than 0.8 seconds.
2 The DISP switch is operated for 0.8 seconds or more to reset.

Display Outline
Current Fuel Consumption
Y129629

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN), provided that the ignition switch is turned ON.
Total Average Fuel Consumption
Y129630

·

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN) since the counter was reset.

·

The display updates every 10 seconds.


Water Temperature Gauge
Y129631

The engine coolant temperature date are displayed with bar graph.
Average Vehicle Speed
Y129632

·

Displays the value that has been calculated by the meter ECU, which is based on the elapsed time and driven distance since the ignition switch was turned ON or since the counter was reset.

·

The display updates every 10 seconds.


Cruising Range
Y129633

Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch is turned ON.
Outside Temperature
Y129634

·

Displays the outside temperature.

·

The display updates every 3.84 second.


ECO Driving Indicator Zone Display
Y129635

Eco driving ratio based on acceleration is shown with a bar graph.
Dimming Mode Display
Y129645

Displays the combination meter brightness.



c.

Warning Display (Models with Dot Display Type Multi-information Display)

i.

The warning display and the advisory display interrupt the display on the multi-information display if the display conditions are met.

Priority Display Master Warning Light Buzzer
1 AWD TEST MODE - -
ADJUSTING LDA CAMERA - -
2 LDA Display - -
3 Door Open (While Driving) Blinks Sounds
Door Open - -
4 AUTO POWER OFF TO CONSERVE BATTERY - -
5 SHIFT TO P POSITION (for Entry and Start System) Blinks Sounds
SHIFT TO P POSITION Blinks Sounds
6 RELEASE PARKING BRAKE Blinks Sounds
KEY NOT DETECTED Blinks Sounds
7 LDA NOT AVAILABLE Illuminates Sounds
CHECK ENTRY AND START SYSTEM Blinks Sounds
BSM NOT AVAILABLE Illuminates Sounds
CHECK CRUISE CONTROL SYSTEM Illuminates Sounds
CHECK LDA SYSTEM Illuminates Sounds
CHECK BSM SYSTEM Illuminates Sounds
CHECK STEERING LOCK SYSTEM Illuminates Sounds
ENGINE OIL PRESSURE LOW Illuminates Sounds
HIGH TRANSMISSION FLUID TEMPERATURE Illuminates Sounds
CHECK AWD SYSTEM Illuminates Sounds
8 TURN POWER OFF Blinks Sounds
KEY DETECTED IN VEHICLE Blinks Sounds
TURN LIGHTS OFF Blinks Sounds
MOON ROOF OPEN Blinks Sounds
DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY Blinks Sounds
DEPRESS CLUTCH PEDAL, TOUCH ENGINES WITCH WITH KEY Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START (for Entry and Start System) Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START Blinks Sounds
SHIFT TO P POSITION TO START Blinks Sounds
9 STEERING LOCK ACTIVE Blinks Sounds
AWD DISABLED Blinks Sounds
AWD OVERHEAT Blinks Sounds
10 KEY BATTERY LOW Illuminates Sounds
DRAIN WATER FROM FUEL FILTER Illuminates Sounds
ENGINE OIL LOW Illuminates Sounds
CHECK AHB SYSTEM Illuminates Sounds
DPF FULL ENGINE SERVICE REQUIRED Illuminates -
11 LOW WASHER FLUID - -
TRC OFF - -
OIL MAINTENANCE REQUIRED SOON - -
OIL MAINTENANCE REQUIRED - -
RESETTING OIL MAINTENANCE DATA - -
RESETTING OF OIL MAINTENANCE DATA INCOMPLETE - -
POWER ON - -
Entry Warning Display - -
DPF FULL SEE OWNER'S MANUAL - -
DPF MANUAL REGENERATION IN PROCESS - -

HINT:

The items displayed differ by vehicle specification.




d.

Customize Display (Models with Dot Display Type Multi-information Display)

i.

The customization display can be switched by pressing and holding the DISP switch for 0.8 seconds or more while the setting display is shown on the cruise information display.


ii.

The customization item can be switched to by pressing the DISP switch for less than 0.8 seconds.


iii.

The setting display can be switched to by pressing the DISP switch for 0.8 seconds or more while a customization item is being displayed.


iv.

Settings can be changed by pressing the DISP switch for less than 0.8 seconds while the setting display is being shown.

Y129636N01
2.26,0.604 2.417,0.802 0.156,0.198 10 1 3.552,1.281 3.708,1.479 0.156,0.198 10 2 5.938,1.281 6.094,1.479 0.156,0.198 10 2 4.646,0.615 4.802,0.813 0.156,0.198 10 1

No. Condition
1 The DISP switch is operated for 0.8 seconds or more.
2 The DISP switch is operated for less than 0.8 seconds.



e.

Eco Driving Indicator

i.

The operating diagram of Eco Driving Indicator Light is as follows:

Y129637E01
0.833,0.271 1.323,0.698 0.49,0.427 10 false Large 0.813,2.906 1.302,3.333 0.49,0.427 10 false Small 0.479,1.635 1.406,1.979 0.927,0.344 10 false Acceleration 3.688,0.865 6.458,1.208 2.771,0.344 10 false Eco Driving Indicator Light will not Turn On 2.688,2.417 5.042,2.708 2.354,0.292 10 false Eco Driving Indicator Light Turns On* 3.417,3.135 4.344,3.479 0.927,0.344 10 false Vehicle Speed 1.76,3.135 2.188,3.448 0.427,0.313 10 false Slow 5.719,3.135 6.146,3.448 0.427,0.313 10 false Fast 0.115,3.448 3.094,3.792 2.979,0.344 10 false *: Will not turn on while the vehicle is stopped.


ii.

When the ECM, using information (such as vehicle speed, accelerator pedal depressed volume, engine speed signal (engine r/min data), and so on), calculates that the vehicle is driven in an Eco-friendly manner, it turns on Eco Driving Indicator Light and shows the bar graph of ECO Driving Indicator Zone Display within Zone of Eco driving.


iii.

When the ECM calculates that the acceleration exceeds Zone of Eco driving, it turns off ECO Driving Indicator Light and blinks the right side of Eco Driving Indicator Zone Display.


iv.

The operation of Eco Driving Indicator is as follows:

Vehicle Condition ECO Driving Indicator Zone Display Eco Driving Indicator Light
Stopped
Y129638

Turns off
Y129639

ECO Driving
Y129640

Turns on
Y129641

Non-ECO Driving
Y129642

Turns off
Y129643



v.

Eco Driving Indicator can be deactivated in the following ways: Eco Driving Indicator Light can be deactivated from Eco Driving Indicator Light customization display of the multi-information display.



f.

Front Seat Belt Warning Function

i.

When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the driver and front passenger seat belt buckle switches and the occupant detection sensor.


ii.

On models except models for G.C.C. countries, the buzzer sounds when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled. After 30 seconds, the sound changes for emphasis. The sound continues for 90 seconds. Once a buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch is turned off.


iii.

On models for G.C.C. countries, when the seat belt is unbuckled, the buzzer sounds 5 times 1.8 seconds after the ignition switch is turned on (IG). The multi buzzer sounds when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled. After 9.6 seconds, the sound changes for emphasis. The sound continues for 20 seconds. Once a multi buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch is turned off.

HINT:

Upon receiving a request from a user who cannot wear a seat belt for a special reason, the buzzer warning can be canceled using the Global TechStraem (GTS). For details, refer to the Repair Manual.



iv.

Occupant Detection Sensor (Except models for Korea)

·

The occupant detection sensor, which is enclosed in the seat cushion of the front passenger seat, is used to detect whether or not the front passenger seat is occupied.

·

This sensor consists of a construction in which 2 electrode sheets sandwich a spacer. When the occupant is seated, the electrode sheets come in contact with each other through the hole provided in the spacer portion, thus enabling the current to flow.

·

Thus, the sensor detects whether or not an occupant is seated in the front passenger seat.



v.

Occupant Detection Sensor (Models for Korea)

·

The occupant detection sensors are installed on brackets connecting the seat rail and the seat frame. The resistance values of these sensors, which vary in accordance with the distortion that acts on the brackets, are output to the occupant detection ECU.

·

The occupant detection ECU constantly monitors the weight on the front passenger seat, and makes a judgment in accordance with the signals from the occupant detection sensor and the state of the front passenger seat belt buckle switch.

·

The occupant detection ECU transmits the signals to the center airbag sensor assemby.




g.

Rear Passengers Seat Belt Reminder Function (Models with Rear Passengers Seat Belt Reminder Function)

Y129644C01
3.396,1.417 3.396,1 true 3.115,1.417 3.115,1 true 3.823,1.406 2.823,1.406 2.823,1.406 2.823,0.99 true 3.875,1.323 4.188,1.479 0.313,0.156 10 *1
*1 Telltale Marker - -


i.

If the meter ECU receives an off signal from the rear door courtesy light switch assembly when the ignition switch is ON, a rear passenger seat belt reminder display is shown on the telltale light assembly. At this time, if the meter ECU receives an on signal from a rear seat belt buckle switch, it will extinguish the telltale light corresponding to the rear seat belt buckle switch which sent the on signal. In addition, the rear passenger seat belt reminder display will automatically turn off approximately 34 seconds after the display.


ii.

If any of the rear seat belts are released while the vehicle speed is above 20 km/h (12 mph), the rear passengers seat belt reminder illuminates and the buzzer is sounded. After 30 seconds, the sound change for emphasis. The sound continues for 90 seconds. Once the buzzer begins to sound, it will continue until the rear seat belt is buckled or the ignition switch is turned off.


iii.

The DISP switch installed on the steering pad switch can be used to show the rear passengers seat belt reminder display as required.




FAIL-SAFE


a.

Eco Driving Indicator

i.

When any of the following conditions are met, Eco Driving Indicator Light is turned off and ECO Driving Indicator Zone Display is stopped:

·

Engine Signal Malfunction

·

CAN Signal Malfunction