Home › Drivetrain › K114F MULTIDRIVE / CVT › CVT SYSTEM › 2015.04–2015.10
NM3090E _52 Drivetrain _036369 K114F MULTIDRIVE / CVT _0168295 CVT SYSTEM CO CONTROL F

K114F MULTIDRIVE / CVT  CVT SYSTEM  CONTROL  CVT CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with shift paddle

*2: Models with segment display type multi-information display

*3: Models with dot display type multi-information display

CVT Fluid Warmer (Transmission Oil Cooler) Warms up the CVT fluid quickly.
Torque Converter Assembly
·

Transmits engine power to the transaxle.

·

Increases engine torque.


Oil Pump Assembly Provides oil pressure necessary for the transaxle operation.
Forward Clutch Connects the input shaft with the sun gear.
Reverse Brake Keeps the planetary carrier stationary.
Shift Solenoid Valve SC Used to switch control of the shift solenoid valve SLU for forward and reverse clutch control.
Shift Solenoid Valve SL Used to switch control of the shift solenoid valve SLU for lock-up clutch control.
Shift Solenoid Valve SLU Performs forward and reverse clutch control or lock-up clutch control depending on the state of the shift solenoid valves SC and SL.
Shift Solenoid Valve SLP Controls the oil pressure of the primary pulley in accordance with the vehicle speed and accelerator pedal position signals to control the speed ratio.
Shift Solenoid Valve SLS Controls the oil pressure of the secondary pulley in accordance with the input shaft torque to control belt clamping force.
Transmission Revolution Sensor (NIN) Detects the primary pulley speed (input speed).
Transmission Revolution Sensor (NOUT) Detects the secondary pulley speed (output speed).
Transmission Revolution Sensor (NT) Detects the turbine speed of the torque converter.
CVT Fluid Temperature Sensor Detects the CVT fluid temperature.
Oil Pressure Sensor Detects the steel belt clamping force.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Control Switch
·

Detects that the shift lever is in M.

·

Detects the driver's upshift and downshift operations when the shift lever is in M.


Shift Paddle Switch (Transmission Shift Switch Assembly)*1 Detects the driver's upshift or downshift request.
Drive Module Switch Assembly Sport Mode Switch Turns the Sport mode on and off.
ECO Mode Switch Turns the ECO mode on and off.
ECM
·

Controls engine output and the electronic control of the CVT system.

·

Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.


Air Conditioning Amplifier Assembly Transmits the operating state of the air conditioning system to the ECM.
Center Airbag Sensor Assembly
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's longitudinal and lateral acceleration and deceleration.


Combination Meter Assembly Shift Position and Gear Range Indicator
·

Indicates the shift lever position.

·

Indicates the gear range (M1 to M7).


Sport Mode Indicator Light Illuminates when the Sport mode switch is pressed to inform the driver that Sport mode is active.
ECO Mode Indicator Light Illuminates when the ECO mode switch is pressed to inform the driver that ECO mode is active.
MIL Illuminates or blinks to alert the driver that the ECM has detected a malfunction.
CVT Fluid Temperature Warning Light*2 Warns the driver by lighting up when the CVT fluid is at a high temperature.
Master Warning Light*3 Warns the driver by lighting up when a message is shown on the multi-information display.
Multi-information Display*3 Displays a message to warn the driver if the CVT fluid reaches a high temperature.
Buzzer
·

Sounds when the shift-down operation is rejected.

·

Warns the driver by sounding when a message is shown on the multi-information display.




SYSTEM CONTROL


a.

Control List

i.

The electronic control system of the K114F CVT consists of the controls listed below:

Control Outline
Engine-CVT Integrated Control Effects coordinate control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy.
Automatic Shift Control (Speed Ratio Control) Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals.
Acceleration Improvement Control Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input.
Deceleration Improvement Control Determines a pulley ratio which allows for high engine speed to be maintained during deceleration, thus ensuring adequate engine braking.
Uphill/Downhill Shift Control Uses the ECM to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by restricting downshifts.
Lock-up Control The ECM sends a current to the shift solenoid valves SC, SL and SLU based on the throttle position sensor signal and vehicle speed signal, and engages or disengages the lock-up clutch.
Flex Lock-up Control By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy.
7-speed Sport Sequential Shiftmatic Enables driving in a specific gear range which is selected using the shift lever, providing engine braking force appropriate to each gear range.
G AI-shift Control Helps to ensure the vehicle proper posture when entering a corner and ensures the driving torque when exiting a corner.



b.

Engine - CVT Integrated Control

i.

To effect fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.

X109756E06
1.76,0.438 2.302,0.646 0.542,0.208 10 false Engine 4.938,1.167 5.479,1.375 0.542,0.208 10 false CVT 4.656,0.083 6.167,0.469 1.51,0.385 10 false Transmission Revolution Sensor (NIN) Signal 5.281,2.063 6.208,2.417 0.927,0.354 10 false Fluid Pressure Control Circuit 4.031,3.125 5.188,3.49 1.156,0.365 10 false Calculation of CVT Control Amount 1.979,3.125 3.302,3.469 1.323,0.344 10 false Calculation of Engine Control Amount 1.99,4.052 3.26,4.417 1.271,0.365 10 false Calculation of Target Torque 1.979,5 3.26,5.365 1.281,0.365 10 false Calculation of Target Engine Output 4.146,4.979 5.021,5.323 0.875,0.344 10 false Calculation of Target Speed 4.281,5.667 4.917,5.865 0.635,0.198 10 false CVT CPU 2.219,5.667 3.042,5.865 0.823,0.198 10 false Engine CPU 1.26,6.479 2.781,6.781 1.521,0.302 10 false Vehicle Speed Signal 2.74,6.479 5.25,6.75 2.51,0.271 10 false Accelerator Pedal Position Signal 0.802,2.906 1.344,3.115 0.542,0.208 10 false ECM



c.

Automatic Shift Control (Speed Ratio Control)

i.

The ECM determines the driving conditions through each input signal and selects the optimal control to achieve output which meets the driver's intentions.

X104364E02
2.875,1.25 4.469,1.635 1.594,0.385 10 false Automatic Shift Control 2.552,0.396 4.708,0.781 2.156,0.385 10 false Acceleration Improvement Control 0.542,1.146 2.167,1.74 1.625,0.594 10 false Deceleration Improvement Control 2.396,2.156 4.885,2.542 2.49,0.385 10 false Shift Control in Uphill/Downhill Traveling 5.01,1.167 6.604,1.823 1.594,0.656 10 false 7-speed Sport Sequential Shiftmatic


ii.

The ECM calculates the target primary pulley speed in accordance with the accelerator pedal position signal, vehicle speed signal, and stop light switch signal, in order to attain an optimal pulley ratio and shifting speed. To adjust the actual primary pulley speed (acquired from the primary speed sensor) to match the target primary pulley speed, the ECM actuates shift solenoid valves SLP and SLS in order to control the pressure of primary pulley and secondary pulley. As a result, the optimal pulley ratio and shifting speed are achieved.

X109757E05
0.771,0.375 2.344,0.573 1.573,0.198 10 Vehicle Speed Signal 0.583,0.698 2.385,0.875 1.802,0.177 10 Stop Light Switch Signal 1.01,1.021 2.146,1.625 1.135,0.604 10 Accelerator Pedal Position Signal 0.625,1.917 2.125,2.594 1.5,0.677 10 Transmission Revolution Sensor (NIN) Signal 2.677,0.438 3.635,1.167 0.958,0.729 10 Target Primary Pulley Speed 2.667,1.635 3.635,2.281 0.969,0.646 10 Actual Primary Pulley Speed 4.281,0.813 5.167,1.802 0.885,0.99 10 Calculation of Control Amount 5.813,0.906 6.75,1.375 0.938,0.469 10 Shift Solenoid Valve SLP 5.802,1.719 6.708,2.271 0.906,0.552 10 Shift Solenoid Valve SLS


iii.

When the shift lever is in D, the system effects engine integrated control to optimize fuel economy characteristics and driving performance.

X114042E02
4.875,0.667 6.333,1.198 1.458,0.531 10 false : Control area 2.448,0.302 3.833,0.979 1.385,0.677 10 false Pulley Ratio (Low) 0.906,1.281 2.344,2.063 1.438,0.781 10 false Primary Pulley Speed 2.74,2.156 4.24,2.563 1.5,0.406 10 false Vehicle Speed 4.25,1.333 5.813,1.896 1.563,0.563 10 false Pulley Ratio (High)


iv.

The Sport mode limits the shift range for the acceleration side and maintains the primary pulley speed at high speeds. This produces a moderate engine braking force and provides an excellent shift response.

X114045E02
4.865,0.667 6.333,1.313 1.469,0.646 10 false : Control area 2.458,0.302 3.729,0.844 1.271,0.542 10 false Pulley Ratio (Low) 4.198,1.323 5.729,1.927 1.531,0.604 10 false Pulley Ratio (High) 0.948,1.198 2.5,1.75 1.552,0.552 10 false Primary Pulley Speed 2.76,2.188 3.906,2.677 1.146,0.49 10 false Vehicle Speed


v.

ECO mode changes the transmission characteristics to ones which prioritize fuel efficient driving to ensure low fuel consumption compared to those of NORMAL mode. This drive mode provides optimal fuel efficiency.



d.

Acceleration Improvement Control

i.

The system determines the driver's acceleration request based on the vehicle speed and changes in the accelerator pedal position. When the system determines this request, it will change the shift characteristics to ones in which the engine speed and vehicle speed increase linearly, providing improved acceleration feeling.

X104368E04
2.625,4.354 2.344,4.354 2.344,4.354 2.594,3.729 true 2.792,2.802 2.51,2.802 2.51,2.802 2.677,2.302 true 3.417,1.323 3.135,1.323 3.135,1.323 3.333,1.823 true 1.271,3.396 2.271,3.906 1,0.51 10 false Acceleration 1.198,1.896 2.448,2.323 1.25,0.427 10 false Engine Speed 5.24,0.948 5.906,1.281 0.667,0.333 10 false Time 0.938,0.51 2.073,1.188 1.135,0.677 10 false Accelerator Pedal Position 5.25,2.438 5.917,2.771 0.667,0.333 10 false Time 5.208,3.865 5.875,4.198 0.667,0.333 10 false Time 3.49,1.25 6.896,1.646 3.406,0.396 10 false Increases Linearly in Accordance with Vehicle Speed 2.875,2.719 7.052,3.115 4.177,0.396 10 false Suppresses Engine Speed Increase at Beginning of Acceleration 2.698,4.271 6.917,4.667 4.219,0.396 10 false Linearly Increases Acceleration Immediately Following Acceleration


ii.

When Sport mode is on, upshifting time is shortened and engine speed increase rate is improved, thus giving a sportier setting compared to when Sport mode is off.

X112041E01
2.656,1.792 2.792,1.99 2.792,1.99 3,1.99 true 3.51,1.313 3.625,1.031 3.625,1.031 3.844,1.031 true 3.083,1.531 3.208,1.719 3.208,1.719 3.469,1.719 true 0.625,0.313 1.833,0.667 1.208,0.354 10 false Accelerator Pedal Depressed Angle 0.885,1.656 1.792,1.896 0.906,0.24 10 false Engine Speed 3.063,1.906 5.521,2.292 2.458,0.385 10 false Re-acceleration response through quick engine speed increase is improved. 3.49,1.635 6.01,1.854 2.521,0.219 10 false Engine speed increase rate is improved. 5.146,2.5 5.542,2.76 0.396,0.26 10 false Time 3.885,0.958 5.688,1.208 1.802,0.25 10 false Upshifting time is shortened. 5.927,0.104 7.135,0.458 1.208,0.354 10 false : Sport mode on 5.927,0.354 7.135,0.708 1.208,0.354 10 false : Sport mode off 5.146,0.625 5.542,0.885 0.396,0.26 10 false Time



e.

Deceleration Improvement Control

i.

During deceleration, a pulley ratio which allows high engine speed to be maintained, is calculated, thus ensuring adequate engine braking.


ii.

During subsequent acceleration, the engine is controlled to generate driving force quickly.

X104369E03
3.073,0.396 2.802,0.396 2.802,0.396 2.802,1.021 false 4.469,1.49 5.396,1.49 false 0.458,2.865 1.604,3.635 1.146,0.771 10 false Accelerator Pedal Operation 0.875,1.281 2.021,1.677 1.146,0.396 10 false Engine Speed 1.625,2.76 1.99,3.156 0.365,0.396 10 false On 1.625,3.281 1.99,3.677 0.365,0.396 10 false Off 4.76,3.438 5.323,3.781 0.563,0.344 10 false Time 4.781,2.313 5.333,2.708 0.552,0.396 10 false Time 3.135,0.323 5.563,1.094 2.427,0.771 10 false Ensures Engine Braking by Maintaining High Engine Speed 5.469,1.396 7.01,2.25 1.542,0.854 10 false Improves Re-acceleration Response through Quick Engine Speed Increase


iii.

When decelerating with Sport mode on, the pulley ratio is fixed in the lower ratio side to achieve a quicker deceleration response and stronger engine braking force compared to when Sport mode is off. In addition, a higher brake pedal force is caused by increasing engine speed when braking hard, and braking downshift control which generates a quick drive force during reaccelerationis used.

X112043E01
3.719,3.031 3.938,2.208 3.938,2.208 4.198,2.208 true 0.635,0.323 1.76,0.667 1.125,0.344 10 false Accelerator Pedal Depressed Angle 0.573,1.281 1.75,1.625 1.177,0.344 10 false Brake Pedal Force 0.833,2.729 1.958,3.073 1.125,0.344 10 false Engine Speed 4.906,3.458 5.438,3.698 0.531,0.24 10 false Time 4.26,2.125 6.615,2.51 2.354,0.385 10 false Raising Engine Speed at Hard Braking 3.76,0.781 4.667,1.135 0.906,0.354 10 false Hard Braking 2.49,0.323 2.823,0.552 0.333,0.229 10 false Off 3.771,0.354 4.073,0.667 0.302,0.313 10 false On 5.896,0.26 7.021,0.604 1.125,0.344 10 false : Sport mode on 5.896,0.51 7.021,0.854 1.125,0.344 10 false : Sport mode off 4.906,1.542 5.438,1.781 0.531,0.24 10 false Time 4.896,0.573 5.427,0.813 0.531,0.24 10 false Time



f.

Uphill/Downhill Shift Control

i.

Uphill/downhill shift control helps perform optimal shifting while driving on a winding uphill or downhill road.


ii.

When the ECM determines the vehicle is traveling uphill, the control restricts upshifting, thus offering smooth driving.


iii.

If a signal indicating that the driver has operated the brake pedal is input when the ECM has determined the vehicle is traveling downhill, the control downshifts to generate optimal engine braking force.

X101083E01
0.552,2.469 1.594,2.719 1.042,0.25 10 without Control 4.552,3.333 5.625,3.542 1.073,0.208 10 Brake Operation 0.74,3.052 1.583,3.271 0.844,0.219 10 with Control 2.094,2.188 2.781,2.396 0.688,0.208 10 Downshift 3.448,2.188 4.135,2.396 0.688,0.208 10 Downshift 5.083,2.802 5.771,3.01 0.688,0.208 10 Downshift 2.854,2.188 3.375,2.396 0.521,0.208 10 Upshift 4.333,2.188 4.854,2.396 0.521,0.208 10 Upshift 4.333,2.802 4.854,3.01 0.521,0.208 10 Upshift 2.542,2.802 3.656,3.01 1.115,0.208 10 Restricts Upshift


iv.

The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.

X109760C02
1.219,0.521 1.01,0.521 1.01,0.521 0.75,0.99 true 5.125,0.813 4.917,0.813 4.917,0.813 4.656,1.292 true 1.26,0.458 1.552,0.656 0.292,0.198 10 *c 5.156,0.729 5.448,0.927 0.292,0.198 10 *d 0.271,0.271 0.563,0.469 0.292,0.198 10 *a 3.865,0.292 4.156,0.49 0.292,0.198 10 *b
*a Uphill *b Downhill
*c Smaller *d Grater
V100135

Reference Acceleration
V100136

Actual Acceleration




g.

Lock-up Control

i.

The lock-up operation range has been expanded from that of previous continuously variable transaxles, thus enabling control to start from low speeds.


ii.

The lock-up operation range during deceleration has been expanded to the low-speed range. This expands the fuel cut range and achieves excellent fuel economy.

X109761E02
0.854,0.927 2.302,1.198 1.448,0.271 10 false Throttle Opening Angle 3.542,2.271 4.49,2.458 0.948,0.188 10 false Vehicle Speed 3.5,1.375 4.479,1.625 0.979,0.25 10 false Lock-up On 2.458,0.375 3.229,0.594 0.771,0.219 10 false Lock-up Off



h.

Flex Lock-up Control

i.

In order to improve the transmission efficiency and also the fuel economy, the shift solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.


ii.

The flex lock-up control consists of flex start control and flex lock-up control during deceleration.


iii.

The flex start control aggressively operates the lock-up clutch during start-off to increase the transmission efficiency, as a result, the engine can run in its most efficient operating range.

X105133E05
3.813,1.281 4.01,0.854 4.01,0.854 4.125,0.854 true 3.135,1.302 2.698,0.49 2.698,0.49 2.927,0.49 true 1.219,1.125 2.167,1.406 0.948,0.281 10 false Engine Speed 3.271,2.292 3.635,2.583 0.365,0.292 10 false Time 4.063,1.885 4.99,2.177 0.927,0.292 10 false Vehicle Speed 2.979,0.406 4.146,0.719 1.167,0.313 10 false Conventional CVT 4.208,0.792 6.698,1.219 2.49,0.427 10 false Decreases engine speed at vehicle start

X105134E05
3.177,1.208 3.667,0.458 3.667,0.458 3.917,0.458 true 1.292,1.063 2.302,1.448 1.01,0.385 10 false Engine Torque 3.135,2.313 4.052,2.635 0.917,0.323 10 false Engine Speed 3.99,0.406 5.667,0.729 1.677,0.323 10 false Flex start operating range 3.698,1.865 5.427,2.188 1.729,0.323 10 false Conventionally used range 3.385,1.094 4.948,1.271 1.563,0.177 10 true High fuel economy range


iv.

Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.



i.

7-speed Sport Sequential Shiftmatic

i.

The 7-speed sport sequential shiftmatic is designed to allow the driver to switch the shift range. After moving the shift lever to M, the driver can select the desired shift range by moving the shift lever to "+" (forward) or "-" (backward). On models with a shift paddle, the shift paddle can be used to change the shift range while the driver is holding the steering wheel. Thus, the driver is able to shift gears with a manual-like feel.


ii.

Through the engine-CVT integrated control, the pulley ratio and engine torque which correspond to various shift speeds are finely controlled, thus improving shift response and achieving reduced shifting shock.

X124252E01
4.99,0.417 6.375,1.448 1.385,1.031 10 false + (UP)/- (DOWN) Operation by Shift Lever (Shift Lever in M 4.906,2.156 6.594,3.281 1.688,1.125 10 false + (UP)/- (DOWN) Operation by Shift Paddle Switch (Transmission Shift Switch) 3.646,1 4.104,1.542 0.458,0.542 10 false ECM 1.917,0.521 2.51,1 0.594,0.479 10 false ETCS-i 1.917,0.938 2.51,1.417 0.594,0.479 10 false ESA 1.979,1.75 2.573,2.229 0.594,0.479 10 false CVT 0.771,1.365 1.365,1.844 0.594,0.479 10 false Engine 2.49,2.76 3.74,3.177 1.25,0.417 10 false Rulley Ratio Control 2.448,3.323 3.865,3.708 1.417,0.385 10 false Fluid Pressure Control


iii.

When the shift lever is in M, this system automatically upshifts or downshifts under the following conditions:

Condition System Control
Engine is under-revving. 1 step downshift
Engine is over-revving. 1 step upshift


iv.

When the shift lever is in D, the driver can momentarily select a desired shift range by operating the shift paddle. Automatic shift control is reverted to under the following conditions:

Condition System Control
The driver continues to push the shift paddle in the "+" direction longer than a predetermined length of time. Reverts to automatic shift control
The driver depresses the accelerator pedal longer than a predetermined length of time while the CVT remains in the same shift range. Reverts to automatic shift control
The vehicle has stopped. Reverts to automatic shift control
The driver has moved the shift lever to M. Transfers to manual shifting


v.

When the vehicle is stopped while the shift lever is in M, the transaxle automatically downshifts to M1.


vi.

When the accelerator pedal is fully depressed and a kickdown operation is performed, a downshift to a gear step determined according to the vehicle speed is performed.


vii.

The ECM will restrict the changing of the shift range if it detects a malfunction in the CVT system.


viii.

If the vehicle speed and engine speed exceed or go below a preset level in response to the driver's downshift operation request, changing the shift range will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.



j.

G AI-shift Control

i.

G AI-shift control is used. When braking, G AI-shift control performs braking downshift in accordance with the actual braking force, producing appropriate engine braking force. Additionally, while determining a corner condition, G AI-shift control restricts unnecessary shift change and maintains engine speed by detecting a lateral G force, improving acceleration control performance and ensuring the drive torque when exiting a corner.

X111730E01
3.021,2.927 3.479,2.677 3.479,2.677 3.604,2.677 true 0.771,0.406 1.188,0.677 0.417,0.271 10 Brake 0.063,1.021 1.198,1.729 1.135,0.708 10 Accelerator Pedal Opening Angle 0.292,2.104 1.25,2.375 0.958,0.271 10 Engine Speed 0.219,2.823 1.188,3.365 0.969,0.542 10 G Force during Cornering 3.688,0.156 4.708,0.458 1.021,0.302 10 Non Restriction 2.104,1.802 2.833,2.094 0.729,0.292 10 Down Shift 3.385,1.604 5.031,1.917 1.646,0.313 10 Restriction of Shift Change 3.677,2.625 5.417,2.958 1.74,0.333 10 While Determining a Corner 0.531,3.729 3.417,4.01 2.885,0.281 10 Downshift for Braking before Entering a Corner 0.521,4.042 3.646,4.333 3.125,0.292 10 Restricts Shift Change while Determining a Corner 0.5,4.375 4.646,4.667 4.146,0.292 10 Smooth Acceleration Control and Quick Exit when Exiting a Corner

HINT:
·

G AI-shift control is turned on by pressing the Sport mode switch. When Sport mode is selected, the Sport mode indicator light in the combination meter assembly illuminates. Pressing the Sport mode switch again turns Sport mode off.

·

When the engine is stopped with Sport mode on, Sport mode is turned off.

·

When the shift lever is in M or temporary sport sequential shiftmatic mode is selected, gear range change operation due to mode change is not performed.

·

If a malfunction is detected in the CVT system, transmission control is performed in normal mode.






FAIL-SAFE


a.

This function minimizes the loss of operability when a malfunction occurs in any sensor or solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, it records the malfunction and information related to the fault. Furthermore, the ECM will illuminate or blink the MIL in the combination meter to inform the driver.


b.

At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.