Home › Drivetrain › K114F MULTIDRIVE / CVT › CVT SYSTEM › from 2015.04
NM3090E _52 Drivetrain _036369 K114F MULTIDRIVE / CVT _0168295 CVT SYSTEM DE DETAILS F

K114F MULTIDRIVE / CVT  CVT SYSTEM  DETAILS  PULLEY AND STEEL BELT  


CONSTRUCTION


a.

The widths of the grooves of the pulleys are changed through hydraulic control.


b.

During acceleration, the operation of the shift solenoid valve SLP increases the oil pressure of the primary pulley, thus decreasing the width of the pulley groove.


c.

During deceleration, the operation of the shift solenoid valve SLP decreases the oil pressure of the primary pulley, thus increasing the width of the pulley groove.


d.

The secondary pulley is hydraulically controlled by the shift solenoid valve SLS. The shift solenoid valve SLS controls the belt clamping pressure to ensure the proper power transmission efficiency.

X117381C01
2.5,0.469 3.021,0.781 true 4.438,0.583 3.917,1.094 true 5.031,1.135 4.469,1.354 true 2.844,3.521 2.563,3.667 true 5.323,3.531 5.042,3.677 true 2.042,4.677 1.76,4.823 true 4.563,4.313 4.094,4.104 true 2.823,5.167 2.24,4.875 true 5.333,5.167 4.75,4.875 true 2.333,0.354 2.646,0.51 0.313,0.156 10 false *1 5.063,1.021 5.375,1.177 0.313,0.156 10 false *2 4.448,0.438 4.76,0.594 0.313,0.156 10 false *3 1.375,3.177 1.688,3.333 0.313,0.156 10 false *a 3.854,3.188 4.167,3.344 0.313,0.156 10 false *b 2.552,3.219 2.865,3.375 0.313,0.156 10 false *c 5.031,3.24 5.344,3.396 0.313,0.156 10 false *d 2.854,3.396 3.167,3.552 0.313,0.156 10 false *2 5.344,3.406 5.656,3.563 0.313,0.156 10 false *2 1.604,4.76 1.917,4.917 0.313,0.156 10 false *3 3.948,4.01 4.26,4.167 0.313,0.156 10 false *3 2.854,5.083 3.167,5.24 0.313,0.156 10 false *1 5.365,5.094 5.677,5.25 0.313,0.156 10 false *1 2.51,5.271 2.823,5.427 0.313,0.156 10 false *d 5.042,5.281 5.354,5.438 0.313,0.156 10 false *c
*1 Secondary Pulley *2 Primary Pulley
*3 Steel Belt - -
*a Pulley Ratio (Low) *b Pulley Ratio (High)
*c Groove Width (Large) *d Groove Width (Small)



e.

The primary pulley uses a double piston construction, resulting in a compact and lightweight assembly. The 2 chambers generate hydraulic pressure to vary the groove width.

X112053C01
1.938,2.167 2.25,2.323 0.313,0.156 10 *a 5.125,2.167 5.438,2.323 0.313,0.156 10 *b
*a Pulley Ratio (Low) *b Pulley Ratio (High)
V100155

Chamber A
V100145

Chamber B



f.

The steel belt consists of elements and 2 rows of steel rings. In contrast to chains and V-belts which transmit power through the use of tensile force, this steel belt uses the compressive action (pushing force) of the elements to transmit power.

X100470C01
3.927,1.531 3.927,1.948 true 1.219,1.583 1.635,1.583 true 2.74,1.833 2.74,2.25 true 2.667,2.302 3.49,2.667 0.823,0.365 10 *1 3.865,2 4.688,2.365 0.823,0.365 10 *2 1.073,1.51 1.542,1.875 0.469,0.365 10 *1
*1 Steel Ring *2 Element




OPERATION


a.

The changing of the pulley ratio is accomplished in a continuously variable manner by varying the widths of the grooves of the primary and secondary pulleys.

Pulley Ratio Low (Shift Lever in D)
X100496C06
1.51,2.135 2.042,2.125 true 1.49,1.052 2.021,1.052 true 3.385,0.594 3.583,0.385 3.583,0.385 3.719,0.385 true 5.146,1.104 5.479,1.104 true 4.458,1.156 4.646,1.521 4.646,1.521 4.813,1.521 true 2.896,2.385 3.292,1.74 3.292,1.74 3.802,1.74 true 3.573,2.063 4.073,2.052 true 3.26,2.927 3.823,2.927 true 1.49,1.635 2.177,1.635 true 3.656,2.458 4.156,2.448 true 1.354,2.052 1.646,2.313 0.292,0.26 10 false *3 4.844,1.427 5.146,1.698 0.302,0.271 10 false *8 3.75,0.281 4.094,0.625 0.344,0.344 10 false *10 5.5,1.01 5.74,1.281 0.24,0.271 10 false *9 1.333,0.938 1.583,1.219 0.25,0.281 10 false *1 1.948,0.344 2.25,0.625 0.302,0.281 10 false *a 1.99,2.604 2.292,2.896 0.302,0.292 10 false *b 4.104,1.958 4.417,2.24 0.313,0.281 10 false *6 4.188,2.344 4.5,2.625 0.313,0.281 10 false *5 3.854,2.844 4.167,3.125 0.313,0.281 10 false *4 1.344,1.542 1.635,1.802 0.292,0.26 10 false *2 3.833,1.635 4.146,1.917 0.313,0.281 10 false *7
*1 Primary Pulley *2 Steel Belt
*3 Secondary Pulley *4 Differential Ring Gear
*5 Reduction Driven Gear *6 Reduction Drive Gear
*7 Differential Drive Pinion *8 Forward Clutch (On)
*9 Input Shaft *10 Reverse Brake (Off)
*a Groove Width (Large) *b Groove Width (Small)


Pulley Ratio High (Shift Lever in D)
X100497C06
1.573,1.573 2.198,1.573 true 1.563,1.031 2.063,1.031 true 3.365,0.573 3.604,0.302 3.604,0.302 3.854,0.302 true 5.156,1.104 5.448,1.104 true 4.458,1.167 4.667,1.563 4.667,1.563 4.875,1.563 true 3.583,2.042 4.219,2.042 true 3.625,2.479 4.24,2.479 true 3.24,3.052 4.208,3.052 true 1.594,2.052 2.021,2.052 true 2.938,2.396 3.292,1.76 3.292,1.76 3.719,1.76 true 1.417,1.49 1.74,1.813 0.323,0.323 10 false *2 4.906,1.469 5.969,1.823 1.063,0.354 10 false *8 3.75,1.656 4.115,1.885 0.365,0.229 10 false *7 5.479,1.01 5.708,1.281 0.229,0.271 10 false *9 1.396,0.917 1.646,1.198 0.25,0.281 10 false *1 1.927,2.625 2.281,2.938 0.354,0.313 10 false *b 2.01,0.375 2.281,0.667 0.271,0.292 10 false *a 4.25,1.948 4.708,2.229 0.458,0.281 10 false *6 4.271,2.375 4.729,2.656 0.458,0.281 10 false *5 4.271,2.958 4.729,3.24 0.458,0.281 10 false *4 1.438,1.969 1.896,2.25 0.458,0.281 10 false *3 3.885,0.208 4.25,0.438 0.365,0.229 10 false *10
*1 Primary Pulley *2 Steel Belt
*3 Secondary Pulley *4 Differential Ring Gear
*5 Reduction Driven Gear *6 Reduction Drive Gear
*7 Differential Drive Pinion *8 Forward Clutch (On)
*9 Input Shaft *10 Reverse Brake (Off)
*a Groove Width (Small) *b Groove Width (Large)


Neutral (Shift Lever in N)
X100498C06
1.583,1.594 2.156,1.594 true 1.583,0.99 2.01,0.99 true 3.375,0.563 3.552,0.292 3.552,0.292 3.76,0.292 true 5.042,1.615 4.823,1.615 4.823,1.615 4.542,1.156 true 5.135,1.104 5.823,1.104 true 1.583,2.104 2.052,2.094 true 3.229,3.01 4.156,3.01 true 3.625,2.458 4.135,2.458 true 3.573,2.021 4.135,2.021 true 2.917,2.354 3.271,1.781 3.271,1.781 3.656,1.781 true 1.438,1.5 1.719,1.719 0.281,0.219 10 false *2 4.198,2.927 4.49,3.156 0.292,0.229 10 false *4 1.438,2.031 1.698,2.25 0.26,0.219 10 false *3 5.854,1.01 6.156,1.229 0.302,0.219 10 false *9 1.417,0.875 1.688,1.125 0.271,0.25 10 false *1 1.927,0.354 2.208,0.708 0.281,0.354 10 false *a 1.979,2.625 2.24,2.833 0.26,0.208 10 false *b 4.167,2.375 4.469,2.594 0.302,0.219 10 false *5 4.167,1.927 4.469,2.146 0.302,0.219 10 false *6 3.688,1.688 3.99,1.906 0.302,0.219 10 false *7 5.073,1.542 5.375,1.76 0.302,0.219 10 false *8 3.802,0.188 4.104,0.406 0.302,0.219 10 false *10
*1 Primary Pulley *2 Steel Belt
*3 Secondary Pulley *4 Differential Ring Gear
*5 Reduction Driven Gear *6 Reduction Drive Gear
*7 Differential Drive Pinion *8 Forward Clutch (Off)
*9 Input Shaft *10 Reverse Brake (Off)
*a Groove Width (Large) *b Groove Width (Small)


Reverse (Shift Lever in R)
X100499C06
1.427,1.594 2.177,1.594 true 1.417,1 2.031,1 true 3.385,0.635 3.563,0.385 3.563,0.385 3.688,0.385 true 4.854,1.49 4.688,1.49 4.688,1.49 4.542,1.167 true 5.146,1.135 5.531,1.135 true 3.552,2.052 4.167,2.052 true 3.625,2.448 4.188,2.448 true 1.448,2.083 2.052,2.083 true 2.906,2.375 3.292,1.781 3.292,1.781 3.729,1.781 true 3.229,3.021 3.979,3.021 true 1.281,1.479 1.563,1.698 0.281,0.219 10 false *2 5.563,1.021 5.854,1.25 0.292,0.229 10 false *9 3.76,1.667 4.021,1.885 0.26,0.219 10 false *7 3.719,0.271 4.021,0.49 0.302,0.219 10 false *10 1.281,0.896 1.552,1.146 0.271,0.25 10 false *1 1.927,0.354 2.208,0.708 0.281,0.354 10 false *a 1.969,2.625 2.229,2.833 0.26,0.208 10 false *b 4.219,2.354 4.521,2.573 0.302,0.219 10 false *5 4.021,2.927 4.313,3.156 0.292,0.229 10 false *4 1.292,1.979 1.552,2.198 0.26,0.219 10 false *3 4.198,1.958 4.5,2.177 0.302,0.219 10 false *6 4.885,1.385 5.177,1.615 0.292,0.229 10 false *8
*1 Primary Pulley *2 Steel Belt
*3 Secondary Pulley *4 Differential Ring Gear
*5 Reduction Driven Gear *6 Reduction Drive Gear
*7 Differential Drive Pinion *8 Forward Clutch (Off)
*9 Input Shaft *10 Reverse Brake (On)
*a Groove Width (Large) *b Groove Width (Small)