Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2015.10–2016.08
NM3090E _51 Engine / Hybrid System _008644 3ZR-FAE ENGINE CONTROL _0048051 SFI SYSTEM DE DETAILS F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  DETAILS  STARTER CONTROL (CRANKING HOLD FUNCTION)  


OPERATION


a.

Models with Idling Stop Control

i.

When first starting the engine, if the certification ECU (smart key ECU assembly) receives a start signal from the engine switch, the certification ECU (smart key ECU assembly) sends an operation signal to the ST No. 1 relay via the park/neutral position switch assembly when the shift lever is in P or N and the engine stop and start ECU sends an operation signal to the ST No. 2 relay to operate the starter assembly. At this time, the certification ECU (smart key ECU assembly) turns the ACC relay operation signal (ACCD) off to prevent flickering of the meter, clock and audio systems.*1


ii.

When first starting the engine, if the certification ECU (smart key ECU assembly) receives a start signal from the engine switch, the certification ECU (smart key ECU assembly) sends an operation signal to the starter relay via the clutch start switch assembly when the clutch pedal is depressed to operate the starter assembly. At this time, the certification ECU (smart key ECU assembly) turns the ACC relay operation signal (ACCD) off to prevent flickering of the meter, clock and audio systems.*2


iii.

When starting the engine during idling stop control, the engine stop and start ECU sends operation signals to the ST No. 1 relay and ST No. 2 relay according to the vehicle condition to operate the starter assembly.*1


iv.

When starting the engine during idling stop control, the engine stop and start ECU sends operation signals to the starter relay according to the vehicle condition to operate the starter assembly.*2


v.

While the engine is cranking, the certification ECU (smart key ECU assembly) and/or engine stop and start ECU continues to send an operation signal to the starter relay until it has been detected that the engine has started successfully. Whether the engine has started successfully is determined by the certification ECU (smart key ECU assembly) and ECM, and once it has been determined that the engine has started successfully, the signal output from the certification ECU (smart key ECU assembly) and/or engine stop and start ECU to the starter relay is stopped.


vi.

The crank hold time and engine speed when it has been determined that the engine has started successfully are determined according to the engine coolant temperature.

*1: Models with Continuously Variable Transaxle (CVT)

*2: Models with manual transaxle

Models with Automatic Transaxle
W130866E01
6.094,1.656 7.021,2.427 0.927,0.771 10 false Engine Stop and Start ECU 4.5,0.896 5.833,2.042 1.333,1.146 10 false Park/Neutral Position Switch Assembly 0.146,0.344 1.052,1.146 0.906,0.802 10 false Engine Switch (Push Start Switch) 1.625,1.01 2.385,2.583 0.76,1.573 10 false Certification ECU (Smart Key ECU Assembly) 3.354,2.771 3.781,3.333 0.427,0.563 10 false ACC Relay 0.615,3.542 1.656,4.177 1.042,0.635 10 false CAN (Bus 2)*1, CAN (V Bus)*2 2.229,3.75 3.135,4.135 0.906,0.385 10 false Engine Speed 4.51,4.281 5.104,4.938 0.594,0.656 10 false ST No. 1 Relay 6.104,4.26 6.698,4.917 0.594,0.656 10 false ST No. 2 Relay 1.833,4.958 2.74,5.344 0.906,0.385 10 false ECM 4.375,5.688 5.49,6.083 1.115,0.396 10 false Starter Assembly 0.115,4.844 1.229,5.531 1.115,0.688 10 false Stop Light Switch Assembly 0.115,5.583 1.042,6.313 0.927,0.729 10 false Crank Position Sensor 2.271,6.479 4.521,6.865 2.25,0.385 10 false Engine Coolant Temperature Sensor 0.229,7.01 2.917,7.344 2.688,0.333 10 false *1: Models with central gateway ECU 0.219,7.385 2.906,7.719 2.688,0.333 10 false *2: Models without central gateway ECU

Models with Manual Transaxle
W130904E01
0.135,0.344 1.052,1.375 0.917,1.031 10 false Engine Switch (Push Start Switch) 1.635,1.208 2.406,2.625 0.771,1.417 10 false Certification ECU (Smart Key ECU) 4.5,1.042 5.74,1.875 1.24,0.833 10 false Clutch Start Switch Assembly 3.365,2.813 3.781,3.563 0.417,0.75 10 false ACC Relay 2.26,3.75 3.458,4.24 1.198,0.49 10 false Engine Speed 0.615,3.521 1.656,4.188 1.042,0.667 10 false CAN (Bus 2)*1, CAN (V Bus)*2 0.104,4.771 1.229,5.51 1.125,0.74 10 false Stop Light Switch Assembly 0.188,5.583 1.104,6.229 0.917,0.646 10 false Crank Position Sensor 2.198,6.479 5.01,6.885 2.813,0.406 10 false Engine Coolant Temperature Sensor 4.021,5.708 5.271,6.031 1.25,0.323 10 false Starter Assembly 4.771,4.365 5.25,5.073 0.479,0.708 10 false Starter Relay 6.26,1.323 6.917,2.896 0.656,1.573 10 false Engine Stop and Start ECU 0.26,7.063 3.292,7.417 3.031,0.354 10 false *1: Models with central gateway ECU 0.25,7.427 3.24,7.813 2.99,0.385 10 false *2: Models without central gateway ECU 1.833,5.156 2.344,5.708 0.51,0.552 10 false ECM




b.

Models without Idling Stop Control

i.

Models with Manual Transaxle

1.

If the certification ECU (smart key ECU assembly) receives a start signal from the engine switch, the certification ECU (smart key ECU assembly) sends an operation signal (STAR) to the starter relay via the clutch start switch assembly when the clutch pedal is depressed to operate the starter assembly. At this time, the certification ECU (smart key ECU assembly) turns the ACC relay operation signal (ACCD) off to prevent flickering of the meter, clock and audio systems.

2.

While the engine is cranking, the certification ECU (smart key ECU assembly) continues to send an operation signal to the starter relay until it has been detected that the engine has started successfully. Whether the engine has started successfully is determined by the certification ECU (smart key ECU assembly) and ECM, and once it has been determined that the engine has started successfully, the signal output from the certification ECU (smart key ECU assembly) to the starter relay is stopped.

3.

The crank hold time and engine speed when it has been determined that the engine has started successfully are determined according to the engine coolant temperature.

W130867E01
5.458,0.49 6.385,0.906 0.927,0.417 10 false Starter Relay 6.323,0.885 6.979,1.656 0.656,0.771 10 false To Starter Assembly 3.281,1.49 5.146,1.906 1.865,0.417 10 false Clutch Start Switch Assembly 5.49,2.333 6.24,2.719 0.75,0.385 10 false ACC Relay 6.323,2.698 7.135,3.375 0.813,0.677 10 false To Electrical Equipment 0.219,1.927 1.542,2.646 1.323,0.719 10 false Engine Switch (Push Start Switch) 2.188,1.854 2.969,2.917 0.781,1.063 10 false Certification ECU (Smart Key ECU) 2.677,3.573 4.719,3.958 2.042,0.385 10 false CAN (Bus 2)*1, CAN (V Bus)*2 1.26,3.677 2.219,4.01 0.958,0.333 10 false Engine Speed 2.396,4.375 3.354,4.708 0.958,0.333 10 false ECM 0.156,4.073 1.583,4.417 1.427,0.344 10 false Crank Position Sensor 0.594,4.51 1.573,5.375 0.979,0.865 10 false Engine Coolant Temperature Sensor 3.427,4.906 5.74,5.208 2.313,0.302 10 false *1: Models with central gateway ECU 3.417,5.167 5.938,5.479 2.521,0.313 10 false *2: Models without central gateway ECU