Home › Drivetrain › K114 MULTIDRIVE / CVT › CVT SYSTEM › 2015.10–2016.08
NM3090E _52 Drivetrain _046774 K114 MULTIDRIVE / CVT _0220995 CVT SYSTEM CO CONTROL F

K114 MULTIDRIVE / CVT  CVT SYSTEM  CONTROL  CVT CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with dynamic radar cruise control system

*2: Models with analog type combination meter assembly

*3: Models with Optitron type combination meter assembly

CVT Fluid Warmer (Transmission Oil Cooler) Warms up the CVT fluid quickly.
Torque Converter Assembly
·

Transmits engine power to the transaxle.

·

Increases engine torque.


Oil Pump Assembly Provides oil pressure necessary for the transaxle operation.
Forward Clutch Connects the input shaft with the sun gear.
Reverse Brake Keeps the planetary carrier stationary.
Shift Solenoid Valve SC Used to switch control of the shift solenoid valve SLU for forward and reverse clutch control.
Shift Solenoid Valve SL Used to switch control of the shift solenoid valve SLU for lock-up clutch control.
Shift Solenoid Valve SLU Performs forward and reverse clutch control or lock-up clutch control depending on the state of the shift solenoid valves SC and SL.
Shift Solenoid Valve SLP Controls the oil pressure of the primary pulley in accordance with the vehicle speed and accelerator pedal position signals to control the speed ratio.
Shift Solenoid Valve SLS Controls the oil pressure of the secondary pulley in accordance with the input shaft torque to control belt clamping force.
Transmission Revolution Sensor (NIN) Detects the primary pulley speed (input speed).
Transmission Revolution Sensor (NOUT) Detects the secondary pulley speed (output speed).
Transmission Revolution Sensor (NT) Detects the forward clutch drum speed (turbine speed).
CVT Fluid Temperature Sensor Detects the CVT fluid temperature.
Oil Pressure Sensor Detects the steel belt clamping force.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Control Switch
·

Detects that the shift lever is in M.

·

Detects the driver's upshift and downshift operations when the shift lever is in M.


Drive Module Switch Assembly Sport Mode Switch Turns the Sport mode on and off.
ECO Mode Switch Turns the ECO mode on and off.
ECM
·

Controls engine output and the electronic control of the CVT system.

·

Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.


Air Conditioning Amplifier Assembly
·

Transmits the operating state of the air conditioning system to the ECM.

·

Outputs the ECO mode signal to the ECM.


Center Airbag Sensor Assembly
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's longitudinal and lateral acceleration and deceleration.


Driving Support ECU Assembly*1 Sends the information about the operation conditions of the dynamic radar cruise control system to the ECM.
Combination Meter Assembly Shift Position and Gear Range Indicator Indicates the shift position.
Sport Mode Indicator Light*2 Illuminates when Sport mode is active.
ECO Mode Indicator Light*2 Illuminates when ECO mode is active.
MIL Illuminates or blinks to alert the driver that the ECM has detected a malfunction.
Multi-information Display*3 Displays that Sport or ECO mode is active.
Buzzer Sounds when the shift-down operation is rejected.


SYSTEM CONTROL


Electronic Control of CVT
Control Outline
Engine-CVT Integrated Control Effects coordinate control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy.
Automatic Shift Control (Speed Ratio Control) Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals.
Acceleration Improvement Control Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input.
Deceleration Improvement Control Determines a pulley ratio which allows for high engine speed to be maintained during deceleration, thus ensuring adequate engine braking.
Uphill/Downhill Shift Control Uses the ECM to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by restricting downshifts.
Lock-up Control The ECM sends a current to the shift solenoid valves SC, SL and SLU based on the throttle position sensor signal and vehicle speed signal, and engages or disengages the lock-up clutch.
Flex Lock-up Control By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy.
7-speed Sport Sequential Shiftmatic Enables driving in a specific gear range which is selected using the shift lever, providing engine braking force appropriate to each gear range.
G AI-shift Control Helps to ensure the vehicle proper posture when entering a corner and ensures the driving torque when exiting a corner.

a.

Engine - CVT Integrated Control

i.

To perform fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.

X124433E01
1.729,0.438 2.646,0.635 0.917,0.198 10 false Engine 4.667,0.198 6.156,0.688 1.49,0.49 10 false Transmission Revolution Sensor NIN Signal 4.948,0.823 5.354,1.177 0.406,0.354 10 false CVT 5.177,2.094 6.458,2.625 1.281,0.531 10 false Oil Pressure Control Circuit 0.813,2.927 1.219,3.281 0.406,0.354 10 false ECM 1.979,3.125 3.292,3.667 1.313,0.542 10 false Calculation of Engine Control Amount 4.021,3.125 5.188,3.667 1.167,0.542 10 false Calculation of CVT Control Amount 1.99,4.052 3.271,4.594 1.281,0.542 10 false Calculation of Target Torque 1.99,4.99 3.271,5.531 1.281,0.542 10 false Calculation of Target Engine Output 4.156,5 5.021,5.563 0.865,0.563 10 false Calculation of Target Speed 2,5.688 3.323,6.052 1.323,0.365 10 false Engine Control CPU 4.063,5.677 5.385,6.042 1.323,0.365 10 false CVT Control CPU 0.49,6.417 1.958,6.771 1.469,0.354 10 false Vehicle Speed Signal 3.26,6.417 5.5,6.688 2.24,0.271 10 false Accelerator Pedal Sensor Signal



b.

Automatic Shift Control (Speed Ratio Control)

i.

The ECM judges the driving conditions through each input signal and selects the optimal control to achieve driving which meets the driver's intentions.

X104364E02
2.875,1.25 4.469,1.635 1.594,0.385 10 false Automatic Shift Control 2.552,0.396 4.708,0.781 2.156,0.385 10 false Acceleration Improvement Control 0.542,1.146 2.167,1.74 1.625,0.594 10 false Deceleration Improvement Control 2.396,2.156 4.885,2.542 2.49,0.385 10 false Shift Control in Uphill/Downhill Traveling 5.01,1.167 6.604,1.823 1.594,0.656 10 false 7-speed Sport Sequential Shiftmatic


ii.

The ECM calculates the target primary pulley speed in accordance with the accelerator pedal position signal, vehicle speed signal, and stop light switch signal, in order to attain an optimal pulley ratio and shifting speed. To allow the actual primary pulley speed (acquired from the primary speed sensor) to match the target primary pulley speed, the ECM actuates the shift solenoid valves SLP and SLS in order to control the pressure of primary pulley and secondary pulley. As a result, optimal pulley ratio and shifting speed have been achieved.

X109757E05
0.771,0.375 2.344,0.573 1.573,0.198 10 Vehicle Speed Signal 0.583,0.698 2.385,0.875 1.802,0.177 10 Stop Light Switch Signal 1.01,1.021 2.146,1.625 1.135,0.604 10 Accelerator Pedal Position Signal 0.625,1.917 2.125,2.594 1.5,0.677 10 Transmission Revolution Sensor (NIN) Signal 2.677,0.438 3.635,1.167 0.958,0.729 10 Target Primary Pulley Speed 2.667,1.635 3.635,2.281 0.969,0.646 10 Actual Primary Pulley Speed 4.281,0.813 5.167,1.802 0.885,0.99 10 Calculation of Control Amount 5.813,0.906 6.75,1.375 0.938,0.469 10 Shift Solenoid Valve SLP 5.802,1.719 6.708,2.271 0.906,0.552 10 Shift Solenoid Valve SLS


iii.

When the shift lever is in D, the system effects engine integrated control to optimize fuel economy characteristics and driving performance.

X114042E02
4.875,0.667 6.333,1.198 1.458,0.531 10 false : Control area 2.448,0.302 3.833,0.979 1.385,0.677 10 false Pulley Ratio (Low) 0.906,1.281 2.344,2.063 1.438,0.781 10 false Primary Pulley Speed 2.74,2.156 4.24,2.563 1.5,0.406 10 false Vehicle Speed 4.25,1.333 5.813,1.896 1.563,0.563 10 false Pulley Ratio (High)


iv.

The Sport mode limits the gear step for the acceleration side and maintains the primary pulley speed at high speeds. This produces a moderate engine braking force and provides an excellent shift response.

X114045E02
4.865,0.667 6.333,1.313 1.469,0.646 10 false : Control area 2.458,0.302 3.729,0.844 1.271,0.542 10 false Pulley Ratio (Low) 4.198,1.323 5.729,1.927 1.531,0.604 10 false Pulley Ratio (High) 0.948,1.198 2.5,1.75 1.552,0.552 10 false Primary Pulley Speed 2.76,2.188 3.906,2.677 1.146,0.49 10 false Vehicle Speed


v.

ECO mode changes the transmission characteristics to ones which prioritize fuel efficient driving to ensure low fuel consumption compared to those of NORMAL mode. This drive mode provides optimal fuel efficiency.



c.

Acceleration Improvement Control

i.

The system determines the driver's acceleration request based on the vehicle speed and the changes in the accelerator pedal position. When the system determines this request, it changes the shift characteristic into one in which the engine speed and vehicle speed increase linearly. This improves the acceleration feeling.

X112040E01
2.042,3.469 1.833,3.469 1.833,3.469 2.094,3.083 true 3.104,0.927 2.75,0.927 2.75,0.927 2.948,1.375 true 2.573,2.26 2.24,2.26 2.24,2.26 2.302,1.865 true 0.573,0.229 1.74,0.635 1.167,0.406 10 false Accelerator Pedal Depressed Angle 0.823,1.49 1.802,1.729 0.979,0.24 10 false Engine Speed 0.896,2.76 1.781,2.979 0.885,0.219 10 false Acceleration 2.094,3.385 7.083,3.729 4.99,0.344 10 false Linearly increases acceleration immediately after depressing the accelerator pedal 5.115,3.115 5.5,3.323 0.385,0.208 10 false Time 2.635,2.188 6.5,2.531 3.865,0.344 10 false Suppresses engine speed increase at beginning of acceleration 5.073,1.896 5.479,2.094 0.406,0.198 10 false Time 3.167,0.854 6.385,1.198 3.219,0.344 10 false Linearly increases in accordance with vehicle speed 5.083,0.552 5.448,0.719 0.365,0.167 10 false Time


ii.

When Sport mode is on, upshifting time is shortened and engine speed increase rate is improved, thus giving a sportier setting compared to when Sport mode is off.

X112041E01
2.656,1.792 2.792,1.99 2.792,1.99 3,1.99 true 3.51,1.313 3.625,1.031 3.625,1.031 3.844,1.031 true 3.083,1.531 3.208,1.719 3.208,1.719 3.469,1.719 true 0.625,0.313 1.833,0.667 1.208,0.354 10 false Accelerator Pedal Depressed Angle 0.885,1.656 1.792,1.896 0.906,0.24 10 false Engine Speed 3.063,1.906 5.521,2.292 2.458,0.385 10 false Re-acceleration response through quick engine speed increase is improved. 3.49,1.635 6.01,1.854 2.521,0.219 10 false Engine speed increase rate is improved. 5.146,2.5 5.542,2.76 0.396,0.26 10 false Time 3.885,0.958 5.688,1.208 1.802,0.25 10 false Upshifting time is shortened. 5.927,0.104 7.135,0.458 1.208,0.354 10 false : Sport mode on 5.927,0.354 7.135,0.708 1.208,0.354 10 false : Sport mode off 5.146,0.625 5.542,0.885 0.396,0.26 10 false Time



d.

Deceleration Improvement Control

i.

During deceleration, the pulley ratio is determined and a high engine speed is maintained, thus ensuring adequate engine braking.


ii.

Engine control, which generates driving force quickly, is conducted during re-acceleration.

X112042E01
2.708,0.969 2.813,0.458 2.813,0.458 3.052,0.458 true 4.438,1.521 4.719,1.521 true 0.51,1.333 1.396,1.604 0.885,0.271 10 Engine Speed 0.229,3.01 1.406,3.396 1.177,0.385 10 Accelerator Pedal Operation 1.49,2.823 1.75,3 0.26,0.177 10 On 1.49,3.323 1.781,3.521 0.292,0.198 10 Off 4.969,3.396 5.375,3.604 0.406,0.208 10 Time 4.958,2.219 5.333,2.458 0.375,0.24 10 Time 4.781,1.438 7.094,2.01 2.313,0.573 10 Improves Re-acceleration Response through Quick Engine Speed Increase 3.115,0.354 5.604,0.74 2.49,0.385 10 Ensures Engine Braking by Maintaining High Engine Speed


iii.

When decelerating with Sport mode on, the pulley ratio is fixed in the lower ratio side to achieve a quicker deceleration response and stronger engine braking force compared to when Sport mode is off. In addition, a higher brake pedal force is caused by increasing engine speed when braking hard, and braking downshift control which generates a quick drive force during re-acceleration is used.

X112043E01
3.719,3.031 3.938,2.208 3.938,2.208 4.198,2.208 true 0.635,0.323 1.76,0.667 1.125,0.344 10 false Accelerator Pedal Depressed Angle 0.573,1.281 1.75,1.625 1.177,0.344 10 false Brake Pedal Force 0.833,2.729 1.958,3.073 1.125,0.344 10 false Engine Speed 4.906,3.458 5.438,3.698 0.531,0.24 10 false Time 4.26,2.125 6.615,2.51 2.354,0.385 10 false Raising Engine Speed at Hard Braking 3.76,0.781 4.667,1.135 0.906,0.354 10 false Hard Braking 2.49,0.323 2.823,0.552 0.333,0.229 10 false Off 3.771,0.354 4.073,0.667 0.302,0.313 10 false On 5.896,0.26 7.021,0.604 1.125,0.344 10 false : Sport mode on 5.896,0.51 7.021,0.854 1.125,0.344 10 false : Sport mode off 4.906,1.542 5.438,1.781 0.531,0.24 10 false Time 4.896,0.573 5.427,0.813 0.531,0.24 10 false Time



e.

Uphill/Downhill Shift Control

i.

The ECM determines that the vehicle is driving uphill or downhill based on the accelerator pedal position sensor signal and the vehicle speed signal. During uphill driving, the ECM limits upshift to achieve smooth driving. During downhill driving, the ECM downshifts upon detecting brake pedal operation, in order to provide moderate engine braking.

X112046C01
0.792,2 1.104,2.156 0.313,0.156 10 *a 0.802,2.365 1.115,2.521 0.313,0.156 10 *b 2.115,2.146 2.427,2.302 0.313,0.156 10 *c 2.76,2.156 3.073,2.313 0.313,0.156 10 *d 2.781,2.49 3.094,2.646 0.313,0.156 10 *e 5.448,0.24 5.76,0.396 0.313,0.156 10 *f 3.365,2.146 3.677,2.302 0.313,0.156 10 *c 4.333,2.125 4.646,2.281 0.313,0.156 10 *d 4.135,2.5 4.448,2.656 0.313,0.156 10 *d 4.927,2.49 5.24,2.646 0.313,0.156 10 *c
*a Without Control *b With Control
*c Downshift *d Upshift
*e Restrict Upshift *f Brake Operation



ii.

The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.

X112047C01
0.854,0.594 1.167,0.75 0.313,0.156 10 *a 3.969,0.979 4.281,1.135 0.313,0.156 10 *b 1.938,1.281 2.25,1.438 0.313,0.156 10 *c 5.031,1.271 5.344,1.427 0.313,0.156 10 *d
*a Smaller *b Greater
*c Uphill *d Downhill
V100135

Actual Acceleration
V100136

Reference Acceleration




f.

Lock-up Control

i.

The lock-up operation range has been expanded from that of previous continuously variable transaxles, thus enabling control to start from low speeds.


ii.

The lock-up operation range during deceleration has been expanded to the low-speed range. This expands the fuel cut range and achieves excellent fuel economy.

X104371E02
0.938,1.177 2.458,1.469 1.521,0.292 10 Throttle Opening Angle 3.188,2.146 4.323,2.49 1.135,0.344 10 Vehicle Speed 5.104,0.385 6.115,0.677 1.01,0.292 10 : Lock-up on



g.

Flex Lock-up Control

i.

In order to improve the transmission efficiency and also the fuel economy, the shift solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.


ii.

The flex lock-up control consists of flex start control and flex lock-up control during deceleration.

1.

Flex Lock-up Control during Deceleration

·

Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.





h.

7-speed Sport Sequential Shiftmatic

i.

The 7-speed sport sequential shiftmatic is designed to allow the driver to switch the gear step. After moving the shift lever to M, the driver can select the desired gear step by moving the shift lever to "+" (upshift) or "-" (downshift). Thus, the driver is able to select gear steps with a manual-like feel. In addition, engine brake force can be obtained in accordance with each gear step.


ii.

Through the engine-CVT integrated control, pulley ratio and engine torque which corresponds to shifting speed are finely controlled, thus improving shifting response and achieving a reduction in shifting shock.

X112013E06
1.281,0.302 3.219,0.615 1.938,0.313 10 false Combination Meter Assembly 2.365,0.708 4.104,1.021 1.74,0.313 10 false CAN (Bus 2*1 or V Bus*2) 2.104,1.438 3.094,1.802 0.99,0.365 10 false ECM 5.448,1.156 6.365,1.729 0.917,0.573 10 false Transmission Control Switch 3.406,1.167 5.177,1.469 1.771,0.302 10 false M Position Signal 3.406,1.552 5.177,1.854 1.771,0.302 10 false Upshift Signal 3.406,1.927 5.177,2.229 1.771,0.302 10 false Downshift Signal 0.115,2.604 1.646,3.125 1.531,0.521 10 false ESA Control and ETCS-i Control Signals 2.948,2.646 4.896,3.198 1.948,0.552 10 false Oil Pressure Control and Pulley Ratio Control Signals 1.479,3.844 2.469,4.208 0.99,0.365 10 false Engine 2.792,3.948 3.781,4.313 0.99,0.365 10 false CVT 3.427,4.24 6.865,4.563 3.438,0.323 10 false *1: Models with automatic air conditioning system 3.427,4.49 6.865,4.813 3.438,0.323 10 false *2: Models with manual air conditioning system


iii.

When the shift lever is in M, this system automatically upshifts or downshifts under the following conditions:

Condition System Control
Engine is under-revving. 1 step downshift
Engine is over-revving. 1 step upshift


iv.

When the vehicle is stopped while the shift lever is in M, the transaxle automatically downshifts to M1.


v.

When the accelerator pedal is fully depressed and a kickdown operation is performed, a downshift to a gear step determined according to the vehicle speed is performed.


vi.

The ECM will restrict the changing of the shift range if it detects a malfunction in the CVT system.


vii.

If the vehicle speed and engine speed exceed or go below a preset level in response to the driver's downshift operation request, changing the gear step will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.



i.

G AI-shift Control

i.

G AI-shift control is used. When braking, G AI-shift control performs braking downshift in accordance with the actual braking force, producing appropriate engine braking force. Additionally, while determining a corner condition, G AI-shift control restricts unnecessary shift change and maintains engine speed by detecting a lateral G force, improving acceleration control performance and ensuring the drive torque when exiting a corner.

X111730E01
3.021,2.927 3.479,2.677 3.479,2.677 3.604,2.677 true 0.771,0.406 1.188,0.677 0.417,0.271 10 Brake 0.063,1.021 1.198,1.729 1.135,0.708 10 Accelerator Pedal Opening Angle 0.292,2.104 1.25,2.375 0.958,0.271 10 Engine Speed 0.219,2.823 1.188,3.365 0.969,0.542 10 G Force during Cornering 3.688,0.156 4.708,0.458 1.021,0.302 10 Non Restriction 2.104,1.802 2.833,2.094 0.729,0.292 10 Down Shift 3.385,1.604 5.031,1.917 1.646,0.313 10 Restriction of Shift Change 3.677,2.625 5.417,2.958 1.74,0.333 10 While Determining a Corner 0.531,3.729 3.417,4.01 2.885,0.281 10 Downshift for Braking before Entering a Corner 0.521,4.042 3.646,4.333 3.125,0.292 10 Restricts Shift Change while Determining a Corner 0.5,4.375 4.646,4.667 4.146,0.292 10 Smooth Acceleration Control and Quick Exit when Exiting a Corner

HINT:
·

G AI-shift control is turned on by pressing the Sport mode switch. When Sport mode is selected, the Sport mode indicator light in the combination meter assembly illuminates. Pressing the Sport mode switch again turns Sport mode off.

·

When the engine is stopped with Sport mode on, Sport mode is turned off.

·

When the shift lever is in M or temporary sport sequential shiftmatic mode is selected, gear range change operation due to mode change is not performed.

·

If a malfunction is detected in the CVT system, transmission control is performed in normal mode.






FAIL-SAFE


a.

This function minimizes the loss of operability when any abnormality occurs in any sensor or shift solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the MIL in the combination meter illuminates or blinks to inform the driver.


b.

At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting a Global TechStream (GTS). For details, refer to the Repair Manual.