Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › from 2015.10
NM3090E _52 Drivetrain _008832 GF1A TRANSFER / 4WD / AWD _0054896 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM CO CONTROL F

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  CONTROL  FOUR WHEEL DRIVE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Transfer Drive force input into the differential is redirected 90 degrees and output to the propeller shaft by the transfer.
Electromagnetic Control Coupling (Transmission Coupling Assembly) Electromagnetic Solenoid Distributes drive torque in accordance with the amperage applied by the 4WD ECU assembly.
Throttle Position Sensor Detects the throttle valve position and outputs it to the ECM.
Crankshaft Position Sensor Detects the engine speed and outputs it to the ECM.
Speed Sensor Detects the wheel speed of each wheel.
Steering Sensor Detects the direction and angle of the steering wheel.
Park/Neutral Position Switch Assembly*1 Detects the shift position of the transaxle and outputs it to the ECM.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Parking Brake Switch Detects when the parking brake is applied.
Differential Lock Switch Switches between Auto and Lock modes.
4WD ECU Assembly
·

Controls the amperage applied to the electromagnetic control coupling solenoid based on signals provided by the ECUs, sensors and switches in order to optimally distribute drive torque in accordance with driving conditions.

·

Turns 4WD/AWD mode off when a parking brake on signal is received from the main body ECU.

·

Turns 4WD/AWD mode off when a shift position signal (P or N) is received from the ECM.*1

·

Operates in cooperation with the skid control ECU to control the torque distribution between the front and rear wheels.


ECM Outputs signals such as the shift position signal*1, throttle position signal and engine speed signal to the 4WD ECU assembly via CAN communication.
Skid Control ECU
·

Outputs signals such as the vehicle speed signal and deceleration signal to the 4WD ECU assembly via CAN communication.

·

Requests torque distribution between the front and rear wheels during cooperative control with 4WD/AWD.


Center Airbag Sensor Assembly
·

Yawrate and Deceleration Sensor


Detects the vehicle's yaw rate, longitudinal and lateral acceleration and sends the detection signals.
Main Body ECU (Multiplex Network Body ECU) Outputs signals such as the parking brake signal to the 4WD ECU assembly via CAN communication.
Combination Meter Assembly Differential Lock Indicator Light Illuminates to inform the driver that 4WD/AWD lock mode is engaged.
4WD Warning Light*2 Illuminates to warn the driver if a malfunction occurs in the 4WD/AWD system.
Master Warning Light*3 Warns the driver by lighting up when a message is shown on the multi-information display.
Multi-information Display*3 Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the 4WD ECU assembly.

*1: Models with automatic transaxle or CVT

*2: Models with analog type combination meter assembly

*3: Models with Optitron type combination meter assembly



SYSTEM CONTROL


Control Function
Auto Mode Control Starting Off Control Performs control which distributes drive force to the rear wheels to ensure traction performance when starting off and avoid the tight corner braking phenomenon*, which occurs during cornering.
Normal Driving Control
·

Performs control which distributes drive force to the rear wheels to ensure acceleration performance when driving straight ahead and cornering stability.

·

When a stable driving condition has been determined, reduces drive force distribution to the rear wheels to improve fuel economy.


Cornering Control Uses pre-torque control, which is based on driver operation input, and yawrate feedback control, which is based on the vehicle status, to achieve the tracing performance desired by the driver.
Braking Control When braking, cancels 4WD/AWD to improve braking effectiveness.
VSC Cooperative Control When accelerating during cornering on slippery surfaces, etc., the dynamic torque control 4WD/AWD system and VSC function cooperate to perform control which achieves smoother acceleration and higher stability compared to previous TRC and VSC functions. As a result, smooth acceleration during turning is made possible.
Lock Mode Control When the vehicle is being driven in gravel or sand and more traction is required, the driver can select Lock mode by operating the differential lock switch. Thus, this mode achieves optimal control in accordance with the driving conditions and transmits as much drive torque as possible to the rear wheels, in a mode that is similar to the locked 4WD/AWD mode.
Engine Output Control If there is a possibility that overdriving could damage the powertrain system, engine output may be restricted.

HINT:

*: Tight corner braking phenomenon: a phenomenon in which a 4WD/AWD vehicle may lurch and decelerate due to a rotational speed difference between the front and rear wheels, such as during low-speed cornering in 4WD/AWD mode.


a.

Auto Mode Control

i.

Starting Off Control

·

The system ensures start-off performance by optimally distributing engine drive torque to the front and rear wheels.

·

To prevent the tight corner braking phenomenon from occurring during low-speed cornering, the system reduces the amount of torque distributed to the rear wheels.

X111795C01
1.729,2.417 2.042,2.573 0.313,0.156 10 *a 5.083,2.417 5.396,2.573 0.313,0.156 10 *b
*a Straightline Driving *b Low-speed Cornering
V100136

Torque Distribution to Rear Wheels - -




ii.

Normal Driving Control

·

During normal driving, when the system judges that the vehicle is traveling steadily, it reduces the amount of torque distribution to the rear wheels. This allows the vehicle to operate in conditions similar to front-wheel-drive, improving fuel economy.

·

The system optimizes torque distribution to the rear wheels to ensure both excellent straightline acceleration performance and excellent driving stability while cornering.

X111796C01
1.521,2.5 1.833,2.656 0.313,0.156 10 *a 4.875,2.5 5.188,2.656 0.313,0.156 10 *b
*a Steady Driving *b Straightline Acceleration
V100136

Torque Distribution to Rear Wheels - -




iii.

Cornering Control

·

The desired driving path of the driver is estimated using information such as the vehicle speed, steering angle, etc., to change drive force distribution according to driving conditions. As a result, excellent driving stability is ensured.

·

Pre-torque control, which is based on driver operation input, and yawrate feedback control, which is based on the vehicle status, are used to correct vehicle oversteer and understeer and achieve the tracing performance desired by the driver.

·

Pre-torque control is linked with driver steering wheel operations and distributes drive force to the rear wheels to improve steering performance when entering a corner (front and rear drive force distribution is 90:10).

·

Yawrate feedback control performs high-speed computation of the ideal yaw rate (calculated by the 4WD ECU assembly when the vehicle is in motion) and actual yaw rate, detects vehicle steering characteristics (oversteer or understeer), and performs optimal control to distribute drive force to the front or rear wheels if required for correction (front and rear drive force distribution changes from 90:10 to 50:50).

X115214C04
0.146,1.125 4.667,3.625 4.521,2.5 0.229,1.198 0.542,1.396 0.313,0.198 10 false *a 0.219,2.615 0.531,2.813 0.313,0.198 10 false *b 1.531,3.313 1.844,3.51 0.313,0.198 10 false *c 3.521,3.406 3.833,3.604 0.313,0.198 10 false *d 1.365,2.271 1.677,2.469 0.313,0.198 10 false *e 4.26,2.885 4.573,3.083 0.313,0.198 10 false *f 6.188,1.01 6.5,1.208 0.313,0.198 10 false *g
*a Yawrate Feedback Control *b Understeer Tendency
*c Target Line *d Oversteer Tendency
*e Drive Force Distribution to Rear Wheels Increased *f Drive Force Distribution to Rear Wheels Reduced
*g Pre-torque Control - -






FUNCTION


a.

4WD/AWD Operation Condition Display (Models with Optitron Type Combination Meter Assembly)

i.

The operation condition of the 4WD/AWD system, which automatically operates according to the longitudinal acceleration, lateral acceleration and steering angle of the vehicle during driving, is shown on the multi-information display.


ii.

The user can recognize how the 4WD/AWD system is operating in response to various conditions, even on slippery roads. This contributes to improved safety while driving with the 4WD/AWD system.


iii.

The driver can operate the steering pad switch to select whether to display or hide the 4WD/AWD system operation condition.

Multi-information Display Outline
X129464

·

Drive force, which the 4WD/AWD system distributes to front and rear wheels, varies depending on the driving conditions.

·

The amount of drive force applied to each wheel is displayed in segments.

·

The number of displayed segments increases when the drive force applied to each wheel is large, and decreases when it is small.

·

When the drive force applied to the rear wheels is large, the capabilities of the 4WD/AWD system are being utilized in conditions that require start-off and driving performance.

·

When the drive force applied to the rear wheels is small, the system has determined that driving conditions are stable and the 4WD/AWD system is being restrained in order to improve fuel economy.

·

The turning angle and direction of the front wheels varies depending on the amount and direction of the driver's steering operation.

·

Longitudinal and lateral acceleration, which vary depending on the driving conditions, are indicated by the position of a sphere over concentric circles placed at the center of the vehicle.

·

The condition of the vehicle is indicated by the position of the sphere relative to the center of the concentric circles as shown below.

Front: decelerating, rear: accelerating, right side: turning left, left side: turning right







FAIL-SAFE


a.

When there is a possibility of causing damage to the drivetrain due to a malfunction in the 4WD/AWD system or rough driving, the system illuminates or blinks the 4WD warning light*1 or master warning light*2, displays a warning message on the multi-information display*2 to inform the driver and stops 4WD/AWD control.

Condition Control 4WD Warning Light*1 or Master Warning Light*2 Multi-information Display*2
4WD/AWD system malfunction 2WD driving (control prohibited) Illuminates AWD System
Malfunction
2WD Mode
Engaged
Visit Your Dealer
4WD/AWD excess driving (warning before AWD control is prohibited) 4WD/AWD driving Slowly AWD System
Overheated
Switching to
2WD Mode
4WD/AWD excess driving 2WD driving (control prohibited) Quickly AWD System
Overheated
2WD Mode
Engaged

i.

When the 4WD ECU assembly judges that the vehicle has stabilized, it resumes 4WD/AWD mode. If the 4WD warning light*1 or master warning light*2 blinks and displays a warning message on the multi-information display*2, take the following actions without turning the engine off:

·

Decelerate the vehicle until the light goes out.

·

Stop the vehicle and wait until the light goes out.

*1: Models with analog type combination meter assembly

*2: Models with Optitron type combination meter assembly






DIAGNOSIS


a.

Furthermore, the 4WD warning light*1 or master warning light*2 in the combination meter assembly illuminates and a warning message is displayed on the multi-information display*2 to inform the driver.

*1: Models with analog type combination meter assembly

*2: Models with Optitron type combination meter assembly



b.

For details of the DTCs that are stored in 4WD ECU assembly memory, refer to the Repair Manual.