Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.10
NM3090E _56 Audio / Visual / Telematics _009044 PARK ASSIST / MONITORING _0058433 BLIND SPOT MONITOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  CONTROL  BLIND SPOT MONITOR CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The blind spot monitor system has the following functions:

Function Outline
Blind Spot Monitor Sensors LH and RH
·

Output millimeter waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected millimeter waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance and the relative speed, and then transmits this information to the built-in signal processing circuit.

·

The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator accordingly.

·

Dim the outer rear view mirror indicator light on the outer rear view mirror assembly.


Outer Rear View Mirror Assembly
·

Outer Rear View Mirror Indicator Light


·

Illuminates when a vehicle is detected in the detection area (blind spot monitor function).

·

Blinks when the turn signal light switch is operated while a vehicle is detected in the detection area (blind spot monitor function).

·

Blinks when another vehicle is detected in the alert area while the vehicle is backing up (RCTA function).


Headlight Dimmer Switch Assembly
·

Turn Signal Light Switch


Transmits the turn signal light switch signal to the blind spot monitor sensor LH and RH.
Combination Meter Assembly Multi-information Display
·

Blind Spot Monitor Main Switch


·

Operating blind spot monitor main switch allows the operation of the blind spot monitor system to be enabled or disabled.

·

When a malfunction is detected in the blind spot monitor sensors or the blind spot monitor sensors determine that control is not possible, a message is displayed on the multi-information display to warn the driver.


Park/Neutral Position Switch Assembly*1 Transmits the shift position signal to the ECM or TCM*2.
Back-up Light Switch Assembly*3 Transmits the on/off signals of the back-up light switch assembly to the ECM.
Central Gateway ECU Transmits the signal between the CAN communication bus.
Steering Sensor Transmits the steering angle signal to the blind spot monitor sensor LH and RH.
Skid Control ECU Transmits the vehicle speed signal to the blind spot monitor sensor LH and RH.
Main Body ECU (Multiplex Network Body ECU)
·

Transmits the destination signal to the blind spot monitor sensor LH and RH.

·

Transmits the taillight signal to the blind spot monitor sensor LH and RH.


ECM and TCM*2 Transmits the reverse signal to the blind spot monitor sensor LH and RH.
RCTA Buzzer (Blind Spot Monitor Buzzer)*4 Sounds when a vehicle is detected in the alert area while backing up.

*1: Models with automatic transaxle or CVT

*2: Models with U660F automatic transaxle

*3: Models with manual transaxle

*4: Models with RCTA function




SYSTEM CONTROL


a.

Operating Condition (Blind Spot Monitor Function)

i.

The blind spot monitor function operates when both of the following conditions are met:

·

The blind spot monitor main switch is on.

·

The vehicle speed is greater than approximately 16 km/h (10 mph).



ii.

The blind spot monitor function can detect vehicles in its detection areas.

·

The detection areas formed by the blind spot monitor sensor LH and RH are as shown below:

Y127779C01
2.625,0.292 2.938,0.448 0.313,0.156 10 false *a 3.729,0.281 4.042,0.438 0.313,0.156 10 false *b 5.656,1.896 5.969,2.052 0.313,0.156 10 false *c 1.563,1.177 1.875,1.333 0.313,0.156 10 false *a 1.563,3.49 1.875,3.646 0.313,0.156 10 false *a 2.656,4.313 2.969,4.469 0.313,0.156 10 false *a 3.729,4.323 4.042,4.479 0.313,0.156 10 false *b 5.656,2.729 5.969,2.885 0.313,0.156 10 false *c
*a 3.0 m (9.8 ft.) *b 1.0 m (3.3 ft.)
*c 0.5 m (1.6 ft.) - -
V100144

Detection Area - -


·

When this vehicle is overtaken by another vehicle in the adjacent lane.

Y127780C01
4.75,2.5 4.75,2.104 true 2.292,1.479 2.292,1.125 true 2.219,1.51 2.531,1.667 0.313,0.156 10 false *a 4.688,2.531 5,2.688 0.313,0.156 10 false *b
*a Another Vehicle *b This Vehicle
V100135

Vehicle Speed (Fast)
V100136

Vehicle Speed (Slow)
V100144

Detection Area - -


·

When another vehicle enters the detection area of this vehicle due to a lane change.

Y127781C01
2.323,2.708 2.323,1.99 true 4.615,3.677 4.615,3.156 true 2.25,7.135 2.25,6.615 true 4.656,7.104 4.656,6.583 true 2.25,2.719 2.563,2.875 0.313,0.156 10 false *a 4.552,3.708 4.865,3.865 0.313,0.156 10 false *b 3.365,3.875 3.677,4.031 0.313,0.156 10 false *c 3.375,7.24 3.688,7.396 0.313,0.156 10 false *d 2.188,7.156 2.5,7.313 0.313,0.156 10 false *a 4.594,7.135 4.906,7.292 0.313,0.156 10 false *b
*a Another Vehicle *b This Vehicle
*c Another vehicle enters the detection area during lane change (merge in) (Type 1). *d Another vehicle enters the detection area during lane change (merge in) (Type 2).
V100135

Motion Direction of Another Vehicle
V100136

Motion Direction of This Vehicle
V100144

Detection Area - -





b.

Operating Condition (RCTA Function)

i.

The RCTA function can detect vehicles in its detection areas.

·

The system continuously measures the relative speed of an approaching vehicle and its distance. If it is determined that the approaching vehicle will cross in the path of this vehicle, the Estimated Crossing Time (ECT) is calculated. When the ECT is 2.5 seconds or less, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer.

Y131345C02
2.656,2.76 2.667,1.865 true 4.323,1.281 4.313,0.719 true 0.521,3.406 0.51,2.844 true 4.271,0.479 4.583,0.677 0.313,0.198 10 false *a 2.604,1.625 2.917,1.823 0.313,0.198 10 false *b 0.49,3.469 0.802,3.667 0.313,0.198 10 false *c 0.958,4.052 1.271,4.25 0.313,0.198 10 false *f 2.51,3.802 2.823,4 0.313,0.198 10 false *e 2.99,3.354 3.302,3.552 0.313,0.198 10 false *f 3.573,3.417 3.885,3.615 0.313,0.198 10 false *d
*a This Vehicle *b Target Vehicle (Approximately 8 km/h (5 mph))
*c Target Vehicle (Approximately 28 km/h (18 mph)) *d Approximately 5.5 m (18.0 ft.)
*e Approximately 20 m (65.6 ft.) *f Target Detection Line
V100144

Alert Area - -


·

Normal Parking

Y131346C01
3.583,0.771 3.583,0.344 true 2.26,2.51 2.26,2.198 true 5.198,2.073 5.198,1.76 true 3.51,0.156 3.823,0.313 0.313,0.156 10 false *a 2.198,2.531 2.51,2.688 0.313,0.156 10 false *b 5.135,2.104 5.354,2.313 0.219,0.208 10 false *b
*a This Vehicle *b Target Vehicle
V100144

Alert Area - -


·

Angle Parking

Y131347C02
3.573,0.729 3.573,0.354 true 1.917,2.49 1.917,2.115 true 4.948,2.094 4.948,1.719 true 3.5,0.167 3.813,0.323 0.313,0.156 10 false *a 1.844,2.51 2.156,2.667 0.313,0.156 10 false *b 4.875,2.125 5.094,2.344 0.219,0.219 10 false *b
*a This Vehicle *b Target Vehicle
V100144

Alert Area - -






FUNCTION


a.

Blind Spot Monitor Function

i.

According to operation conditions, the blind spot monitor function promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that another vehicle has entered the blind spot monitor sensor detection area of this vehicle.


ii.

The outer rear view mirror indicator light informs the driver that a vehicle is present in the blind spot detection area by illuminating when the turn signal light switch is not operated, and by flashing when a vehicle is present and the turn signal light switch is operated.

Y194335E01
5.198,0.552 6.615,1.208 1.417,0.656 10 false Outer Rear View Mirror Assembly RH 5.177,1.219 6.594,1.875 1.417,0.656 10 false Outer Rear View Mirror Indicator Light 0.51,0.542 1.927,1.198 1.417,0.656 10 false Outer Rear View Mirror Assembly LH 0.5,1.198 1.917,1.854 1.417,0.656 10 false Outer Rear View Mirror Indicator Light 5.333,2.75 6.5,3.333 1.167,0.583 10 false Blind Spot Monitor Sensor RH 3,3.177 4.167,3.76 1.167,0.583 10 false CAN (Local Bus) 0.635,2.771 1.802,3.354 1.167,0.583 10 false Blind Spot Monitor Sensor LH 0.229,3.458 1.396,4.042 1.167,0.583 10 false CAN (Bus 5) 0.417,4.052 1.865,4.521 1.448,0.469 10 false Central Gateway ECU 2.344,3.927 4,4.583 1.656,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 4.708,3.865 6.958,4.25 2.25,0.385 10 false Headlight Dimmer Switch Assembly 4.698,4.302 6.5,4.667 1.802,0.365 10 false - Turn Signal Light Switch 4.823,5.167 6.677,5.521 1.854,0.354 10 false Combination Meter Assembly 4.833,5.594 6.688,5.948 1.854,0.354 10 false Multi-information Display 4.75,6.042 6.833,6.406 2.083,0.365 10 false - Blind Spot Monitor Main Switch 3.792,5.958 4.792,6.354 1,0.396 10 false CAN (Bus 2) 3.125,6.76 4.125,7.156 1,0.396 10 false Speed Sensors 1.396,5.323 2.396,5.719 1,0.396 10 false ECM 1.094,6.031 2.177,6.427 1.083,0.396 10 false Steering Sensor 1.073,6.74 2.219,7.156 1.146,0.417 10 false Skid Control ECU



b.

RCTA Function (Models with RCTA Function)

i.

According to operation conditions, the RCTA function promotes safety confirmation by using the outer rear view mirror indicator lights and RCTA buzzer to inform the driver that another vehicle has entered the blind spot monitor sensor alert area of this vehicle.


ii.

When this vehicle is reversing, if a vehicle enters the alert area of the blind spot monitor sensors and it is determined the vehicle will cross in the path of this vehicle, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer.

Y194336E01
2.417,5.146 2.542,4.698 2.542,4.698 2.625,4.698 true 5.219,0.146 6.667,0.854 1.448,0.708 10 false Outer Rear View Mirror Assembly RH 5.219,0.802 6.667,1.51 1.448,0.708 10 false Outer Rear View Mirror Indicator Light 2.792,0.958 4.24,1.667 1.448,0.708 10 false RCTA Buzzer (Blind Spot Monitor Buzzer)*1 5.333,2.396 6.51,3.135 1.177,0.74 10 false Blind Spot Monitor Sensor RH 0.594,0.146 1.906,0.896 1.313,0.75 10 false Outer Rear View Mirror Assembly LH 0.594,0.823 1.906,1.573 1.313,0.75 10 false Outer Rear View Mirror Indicator Light 0.615,2.396 1.927,3.146 1.313,0.75 10 false Blind Spot Monitor Sensor LH 2.917,2.781 4.073,3.052 1.156,0.271 10 false CAN (Local Bus) 5.302,3.49 6.646,4.156 1.344,0.667 10 false Back-up Light Switch Assembly*2 2.375,3.521 4.042,4.167 1.667,0.646 10 false Main Body ECU (Multiplex Network Body ECU) 0.49,3.594 2.156,4.24 1.667,0.646 10 false Central Gateway ECU 4.917,4.802 6.938,5.146 2.021,0.344 10 false Combination Meter Assembly 4.813,5.302 6.833,5.646 2.021,0.344 10 false Multi-information Display 4.781,5.646 6.875,6 2.094,0.354 10 false - Blind Spot Monitor Main Switch 2.688,4.615 4.354,5.26 1.667,0.646 10 false CAN (Sub Bus 15) 1.406,5.083 2.01,5.375 0.604,0.292 10 false ECM 2.948,5.594 3.552,5.885 0.604,0.292 10 false TCM*4 4.75,6.521 5.927,6.833 1.177,0.313 10 false Skid Control ECU 4.896,7.271 6.073,7.583 1.177,0.313 10 false Speed Sensors 0.969,6.146 2.302,6.802 1.333,0.656 10 false Park/Neutral Position Switch Assembly*3 1.115,7.01 2.156,7.302 1.042,0.292 10 false Steering Sensor 0.073,7.229 1.115,7.521 1.042,0.292 10 false CAN (Bus 2) 0.677,7.698 2.667,7.969 1.99,0.271 10 false *1: Models with RCTA function 3.563,7.688 6.583,7.958 3.021,0.271 10 false *3: Models with automatic transaxle or CVT 3.563,8.01 6.583,8.281 3.021,0.271 10 false *4: Models with U660F automatic transaxle 0.677,8.021 2.927,8.344 2.25,0.323 10 false *2: Models with manual transaxle 0.198,3.094 1.083,3.344 0.885,0.25 10 false CAN (Bus 5)




DIAGNOSIS


a.

The blind spot monitor system is equipped with a diagnosis function that can display warning messages in the multi-information display. For details, refer to the Repair Manual.