Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.10–2016.08
NM3090E _58 Vehicle Interior _009125 METER / GAUGE / DISPLAY _0050691 METER / GAUGE SYSTEM CO CONTROL F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  CONTROL  COMBINATION METER  


SYSTEM CONTROL


a.

Operating Condition

i.

Eco Driving Indicator

·

Eco Driving Indicator starts to operate when all of the following conditions are met:

Condition Ignition switch is ON.
Engine is running.
Shift lever is in D.
Drive mode is Normal or ECO mode.
Vehicle speed is 130 km/h (80.8 mph) or more

·

Eco Driving Indicator stops operation when any of the following conditions is met:

Condition Ignition switch is off.
Engine is stopped.
Shift lever is in any position other than D.
Drive mode is any other mode except Normal or ECO mode.
Vehicle speed is 130 km/h (80.8 mph) or less





FUNCTION


a.

Buzzer Function

i.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:

Item
Driver Seat Belt Warning (Max. 5 times) Driver Seat Belt Warning (Once)
Front Passenger Seat Belt Warning (Once) Front Seat Belt Warning (Level 2)
Front Seat Belt Warning (Level 1) Lane Departure Alert Cancel Warning
Lane Departure Alert Warning Lane Departure Alert No Hands Detect Warning
Engine Oil Pressure Warning Speed Warning
Speed Limiter Stop and Start System Warning
EPS Warning Engine Coolant High Temperature Warning
Brake System Temperature Rise Warning/Active Test Brake System Temperature High Warning
Entry and Start System Warning 2 (Intermittent: Maximum 9 Times) Entry and Start System Warning (Once)
Multi-information Display Warning Road Sign Assist System Warning
Sway Warning Accelerator Depression Hold Warning
Parking Brake Engaged Warning Key Reminder
Door Open while Driving Warning Shift Reject
Light Reminder Immobiliser Certification Reminder
Turn Signal/Hazard Warning Operation Radar Cruise Control Cancelation due to Low Speed Warning

HINT:

The buzzer function differs by vehicle specification.




b.

Multi-information Display (Models with Optitron Type Combination Meter Assembly)

i.

Display Function Flow

·

The multi-information display can be switched as shown in the flowchart below:

Y184574E02
1.563,0.01 2.021,0.208 0.458,0.198 10 false (1) 1.865,0.26 2.323,0.458 0.458,0.198 10 false (2) 0.427,0.865 1.927,1.26 1.5,0.396 10 false Warning Display (3) 3.51,0.229 3.969,0.427 0.458,0.198 10 false OFF 5.208,0.021 5.667,0.219 0.458,0.198 10 false (1) 4.927,0.25 5.385,0.448 0.458,0.198 10 false (2) 2.865,0.844 4.521,1.354 1.656,0.51 10 false Ignition Switch from off to ACC or ON 5.104,0.854 6.938,1.375 1.833,0.521 10 false Door Unlock Mode Display*1 3.094,1.896 4.344,2.198 1.25,0.302 10 false Opening Display 3.719,2.302 4.177,2.5 0.458,0.198 10 false (5) 0.302,3.042 1.49,3.573 1.188,0.531 10 false Diagnosis Display 1.698,2.854 1.927,3.052 0.229,0.198 10 false (1) 1.792,3.344 2.042,3.531 0.25,0.188 10 false (2) 2.938,2.969 4.708,3.292 1.771,0.323 10 false Information Display (4) 2.521,3.333 4.354,3.656 1.833,0.323 10 false - Drive Information Tab 2.521,3.656 4.156,3.958 1.635,0.302 10 false - Navigation Tab*2 2.521,4.021 4.25,4.323 1.729,0.302 10 false - Audio Tab*2,*3 2.521,4.385 4.969,5 2.448,0.615 10 false - Dynamic Radar Cruise Control*4/Lane Departure Alert Display*4 2.521,5.01 4.802,5.417 2.281,0.406 10 false - Stop and Start Information Tab*5 2.521,5.354 4.656,5.677 2.135,0.323 10 false - Message Tab 2.531,5.74 4.469,6.052 1.938,0.313 10 false - Settings Tab 5.125,2.823 5.583,3.021 0.458,0.198 10 false (1) 5.094,3.344 5.323,3.531 0.229,0.188 10 false (2) 5.677,3.021 6.771,3.615 1.094,0.594 10 false Warning Display 5.156,3.969 5.615,4.167 0.458,0.198 10 false (1) 5.104,4.49 5.333,4.688 0.229,0.198 10 false (2) 5.635,3.906 6.792,5.052 1.156,1.146 10 false Dynamic Radar Cruise Control System Display*4 5.219,5.354 5.677,5.552 0.458,0.198 10 false (1) 5.125,5.938 5.385,6.115 0.26,0.177 10 false (2) 5.542,5.354 6.854,6.469 1.313,1.115 10 false Lane Departure Alert System Display*4 0.24,4.948 1.531,6.458 1.292,1.51 10 false Turn-by-turn Navigation Display*2 1.698,5.24 2.156,5.438 0.458,0.198 10 false (1) 1.802,5.708 2.052,5.896 0.25,0.188 10 false (2) 4.615,6.927 7.135,7.281 2.521,0.354 10 false *1: Models for Korea 4.615,7.271 7.01,7.615 2.396,0.344 10 false *2: Models with navigation system 4.594,7.635 7.115,7.99 2.521,0.354 10 false *3: Models with display audio system 4.604,8.021 7.115,8.396 2.51,0.375 10 false *4: Models with Toyota Safety Sense 4.615,8.396 6.969,8.781 2.354,0.385 10 false *5: Models with stop and start system 2.948,7.271 4.281,7.813 1.333,0.542 10 false Ignition Switch ON to OFF 2.375,7.167 2.656,7.375 0.281,0.208 10 false (2) 1.938,8.281 2.396,8.479 0.458,0.198 10 false (1) 3.49,8.406 3.948,8.604 0.458,0.198 10 false OFF 3.781,8.094 4.24,8.292 0.458,0.198 10 false (6) 0.448,7.271 1.75,7.823 1.302,0.552 10 false Warning Display (3)


(1) Conditions are not met.
(2) Conditions are met.
(3) If there are multiple display requests, items will be displayed in sequence.
(4) Item or display is selected by operating the steering pad switch assembly switch.
(5) After ignition switch is turned to ON.
(6) ODO display is displayed for a certain period of time after the ignition switch is turned off.


ii.

Display Tab Operation

·

The information currently displayed can be switched using the RIGHT/LEFT switch on the steering pad switch assembly.

Y190103C01
5.479,1.885 4.875,1.031 true 3.083,1.76 3.521,0.823 true 6.125,2.667 5.656,1.896 true 3.49,0.635 3.802,0.833 0.313,0.198 10 false *1 4.698,0.813 5.01,1.01 0.313,0.198 10 false *a 6.104,2.708 6.417,2.906 0.313,0.198 10 false *b 0.125,3.792 0.479,3.99 0.354,0.198 10 false *c 1.979,3.802 2.583,4.01 0.604,0.208 10 false *d (*A) 3.854,3.781 4.573,3.958 0.719,0.177 10 false *e (*B) 5.813,3.76 6.427,3.979 0.615,0.219 10 false *f (*C) 5.813,6.354 6.458,6.583 0.646,0.229 10 false *g (*D) 3.896,6.354 4.208,6.552 0.313,0.198 10 false *h 1.99,6.365 2.302,6.563 0.313,0.198 10 false *i 0.115,8.604 0.427,8.802 0.313,0.198 10 false *j
*A Models with Navigation System *B Models with Navigation System or Display Audio System
*C Models with Toyota Safety Sense *D Models with Stop and Start System
*1 Steering Pad Switch Assembly - -
*a LEFT Switch *b RIGHT Switch
*c Drive Information *d Navigation Information
*e Audio Information *f Dynamic Radar Cruise Control System / Lane Departure Alert System Information
*g Stop and Start System Information *h Warning Message
*i Settings *j The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen.
V100136

RIGHT Switch Operation
V100135

LEFT Switch Operation




iii.

Drive Information

·

Drive information shows vehicle information such as drivable range and fuel consumption.

·

The drive information can be switched using the UP/DOWN switch on the steering pad switch assembly.

Y192089C02
3.094,1.74 3.521,0.927 true 5.573,1.771 5.073,1.135 true 6.083,2.75 5.583,2 true 3.51,0.781 3.823,0.938 0.313,0.156 10 false *1 4.917,0.969 5.229,1.125 0.313,0.156 10 false *a 6.104,2.792 6.417,2.948 0.313,0.156 10 false *b 0.104,3.729 0.417,3.885 0.313,0.156 10 false *c 2.01,3.781 2.323,3.938 0.313,0.156 10 false *d 3.938,3.792 4.25,3.948 0.313,0.156 10 false *e 5.865,3.781 6.177,3.938 0.313,0.156 10 false *f 5.844,6.135 6.573,6.396 0.729,0.26 10 false *g (*A) 3.938,6.135 4.698,6.375 0.76,0.24 10 false *h (*B) 2.021,6.125 2.333,6.281 0.313,0.156 10 false *i 0.188,8.531 0.375,8.865 0.188,0.333 10 false *j
*A Models with Toyota Safety Sense *B 4WD/AWD Models
*1 Steering Pad Switch Assembly - -
*a UP Switch *b DOWN Switch
*c After Start Display *d After Reset Display
*e After Refuel Display *f Eco Indicator
*g Sway Warning Display *h Dynamic Torque Control 4WD System Display
*i Blank *j The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen.
V100136

DOWN Switch Operation
V100135

UP Switch Operation




iv.

Setting Function

·

The items displayed on the multi-information display can be customized.

·

The items can be selected on the information setting screen.

Item Available Setting
Language The language used on the multi-information display can be selected:
·

English

·

German

·

French

·

Spanish

·

Italian

·

Russian

·

Turkish


HINT:

The selectable languages may differ depending on the model or region.


Unit The unit displayed on the multi-information display can be selected.
·

miles (MPG)

·

km (L/100 km)

·

km (km/L)


HINT:

The selectable units may differ depending on the model.


Eco Driving Indicator Light The Eco driving indicator light can be switched on or off.
·

On

·

Off


Drive information screen The drive information screen can be selected.
LDA (Lane Departure Alert) The following settings can be changed for the lane departure alert system.
·

Steering Assist

·

Alert sensitivity

·

Vehicle sway warning

·

Vehicle sway warning sensitivity


PCS (Pre-Crash Safety System) The following settings can be changed for the pre-crash safety system.
·

Turning the pre-crash safety system on and off

·

Alert timing


RSA (Road Sign Assist) The following settings can be changed for the road sign assist system.
·

Excess speed notification method

·

Excess speed notification level

·

Other notifications method


PBD (Power Back Door System) The following settings can be changed for the power back door system.
·

Opening angle

·

Operation buzzer volume


BSM (Blind Spot Monitor System) The blind spot monitor system can be turned on and off.
Toyota Parking Assist-sensor System The Toyota parking assist-sensor system can be turned on and off.
Interruption Display The following displays that appear as soon as the set conditions are met can be switched to on or off.
·

Turn-by-turn Navigation Display

·

Incoming Telephone Display

·

Light Control Rheostat Display


Accent Color The accent color can be changed:
·

Clear Blue

·

Clear Turquoise

·

Deep Orange

·

Radiant Orange


Initialization The setting items can be initialized.


HINT:

The items displayed differ by vehicle specification.



v.

Warning Mode Function

·

When a warning is necessary, the warning display interrupts the display in the multi-information display.

·

The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.


Priority Display Message Master Warning Light Buzzer
1 4WD TEST MODE - -
ADJUSTING LDA CAMERA - -
ADJUSTING FRONT RADAR BEAM - -
CHECKING PRE-CRASH BRAKE - -
CHECKING CRUISE CONTROL C/D - -
CHECKING CRUISE CONTROL BRAKE - -
BRAKE! - -*
2 Graphic Display (Pre-crash Safety System) - -
Graphic Display (Dynamic Radar Cruise Control System and Lane Departure Alert System) - -
Braking Power Low Stop in a Safe Place See Owner's Manual Illuminates Sounds
3 Door Open (While Driving) Blinks Sounds
Door Open - -
Clearance Sonar Obstruction Detection - -
Parking Assist Malfunction - -
Clean Parking Assist Sensor - -
4 Power Turned Off to Save Battery - -
5 Shift to P Before Exiting Vehicle Blinks Sounds
6 Release Parking Brake Blinks Sounds
Key not detected Check key location Blinks Sounds
7 Shift to neutral and depress clutch. Blinks Sounds
Speed Limit Exceeded - -
LDA Hold Steering Wheel and Graphic Display - -
LDA Steering Assist Unavailable Hold Steering Wheel Illuminates Sounds
8 SRS Airbag System Malfunction Visit Your Dealer Illuminates Sounds
Antilock Brake System Malfunction Visit Your Dealer - Sounds
Engine Coolant Temp High Stop in a Safe Place See Owner's Manual Illuminates -
Charging System Malfunction See Owner's Manual - -
Radar Cruise Control Unavailable Clean Sensor Illuminates Sounds
Radar Cruise Control Unavailable Illuminates Sounds
Radar Cruise Control Unavailable Depress Brake to Resume Driving - -
Smart Entry & Start System malfunction See owner's manual Blinks Sounds
Blind Spot Monitor Unavailable Illuminates Sounds
Cruise Control Malfunction Visit Your Dealer Illuminates Sounds
Cruise Control Fault Press Brake to Deactivate Visit Your Dealer Illuminates Sounds
CHECK SPEED LIMITER SYSTEM Illuminates Sounds
Lane Departure Alert Malfunction Visit Your Dealer Illuminates Sounds
Forward Camera System Unavailable Illuminates Sounds
LDA Steering Assist Deactivated Warnings Available Illuminates Sounds
Lane Departure Alert Turned On Steering Assist Active - -
Lane Departure Alert Turned On Steering Assist Inactive - -
Forward Camera System Unavailable Clean Windshield Illuminates Sounds
Pre-crash Safety Malfunction Visit Your Dealer Illuminates Sounds
Blind Spot Monitor System Malfunction Visit Your Dealer Illuminates Sounds
Oil Pressure Low Stop in a Safe Place See Owner's Manual Illuminates -
Transmission Fluid Temp High See Owner's Manual Illuminates Sounds
AWD System Malfunction 2WD Mode Engaged Visit Your Dealer Illuminates Sounds
Radar Cruise Active Please Pay Attention to Other Vehicles - -
Lane Departure Alert Unavailable Below Approx 50km/h - -
Lane Departure Alert Unavailable at Current Speed - -
9 Graphic Display (Dynamic Radar Cruise Control System and Lane Departure Alert System) - -
Stop & Start System Malfunction Visit Your Dealer Illuminates Sounds
Turn Off Vehicle Blinks Sounds
Detected Sway Pattern of vehicle Would you like to take rest? - -
Detected LDA Repeatedly Please take a rest - -
Key Left inside Vehicle Blinks Sounds
Turn Lights Off Blinks Sounds
Moon Roof Open Blinks Sounds
Depress Brake and Then Touch Key to Engine Switch Blinks Sounds
Depress brake and then start engine Blinks Sounds
Depress clutch and the start engine. Blinks Sounds
Shift to P to start. Blinks Sounds

Priority Display Message Master Warning Light Buzzer
10 STEERING LOCK ACTIVE Blinks Sounds
AWD System Overheated 2WD Mode Engaged Blinks Sounds
AWD System Overheated Switching to 2WD Mode Blinks Sounds
11 KEY BATTERY LOW Illuminates Sounds
Headlight System Malfunction Visit Your Dealer Illuminates Sounds
Water accumulation in fuel filter. Check owner's manual. Illuminates Sounds
Engine Oil Level Low Add or Replace Illuminates Sounds
Headlight System Malfunction Visit Your Dealer Illuminates Sounds
Check RSA System Illuminates Sounds
DPF FULL ENGINE SERVICE REQUIRED Illuminates -
12 Windshield Washer Fluid Low - -
Fuel Low - -
Roads May Be Icy Drive with Care - -
Traction Control Turned Off - -
Traction Control Turned Off - -
Oil Maintenance Required Soon - -
Maintenance Required Soon - -
Oil Maintenance Required Visit Your Dealer - -
Maintenance Required Visit Your Dealer - -
Resetting Maintenance Data - -
RESETTING OF OIL MAINTENANCE DATA INCOMPLETE - -
Power on - -
Graphic Display (Smart Entry and Start System) - -
VSC Turned Off Pre-crash Brake System Unavailable - -
Pre-crash Safety Unavailable - -
High Power Consumption Partial Limit On AC/Heater Operation - -
Pre-Crash Safety Unavailable Wait a Moment - -
Pre-Crash Safety Unavailable Clean Radar Sensor - -
Pre-Crash Safety Off - -
DPF FULL SEE OWNER'S MANUAL - -
DPF MANUAL REGENERATION IN PROCESS - -
Theft Sensor Turned Off - -
Theft Sensor Turned On - -

HINT:

*: PCS buzzer (skid control buzzer) operation is activated.

The warning message differs by vehicle specification.




c.

Multi-information Display (Analog Type Combination Meter Assembly )

i.

The multi-information display can be switched by operating the DISP switch located on the steering pad switch assembly


ii.

The multi-information display indicates as follows:

Display Outline*1
Cruise Information In the cruise information display, 6 types of information can be displayed:
·

Current Fuel Consumption

·

Average Fuel Consumption

·

Average Vehicle Speed

·

Cruising Range

·

Outside Temperature

·

ECO Driving Indicator Zone Display*2


Water Temperature Gauge The engine coolant temperature date are displayed with bar graph.
Customization*2 The Eco Driving Indicator Light can be set up from this screen. The customization display is available only while the vehicle is stopped. If vehicle movement is detected during setup, the setup will be canceled automatically.

HINT:

*1: The items displayed differ by vehicle specification.

*2: When the ECO driving indicator zone display is selected by customization function.



iii.

Cruise Information Display

The cruise information display can be switched by operating the DISP switch. The counter can be reset by pressing and holding the DISP switch for 0.8 seconds or more.


Y129603N01
0.781,1.719 0.938,1.917 0.156,0.198 10 false 1 0.771,3.354 0.927,3.552 0.156,0.198 10 false 1 2.323,3.885 2.479,4.083 0.156,0.198 10 false 1 3.854,3.167 4.333,3.385 0.479,0.219 10 false b, 1 4.729,3.917 5.208,4.135 0.479,0.219 10 false a, 1 6.063,3.156 6.542,3.375 0.479,0.219 10 false a, 1 6.302,1.521 6.458,1.719 0.156,0.198 10 false 1 2.156,0.625 2.313,0.823 0.156,0.198 10 false 1 4.625,0.635 4.781,0.833 0.156,0.198 10 false 1 3.583,1.51 3.74,1.708 0.156,0.198 10 false 2 3.281,3.156 3.438,3.354 0.156,0.198 10 false 2 5.833,1.5 5.99,1.698 0.156,0.198 10 false 2 6.208,4.813 6.365,5.01 0.156,0.198 10 false 2 4.729,2.26 5.208,2.479 0.479,0.219 10 false b, 1

No. Condition
a Standard display mode
b Eco display mode
1 The DISP switch is operated for less than 0.8 seconds.
2 The DISP switch is operated for 0.8 seconds or more to reset.

Display Outline
Current Fuel Consumption
Y129629

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN), provided that the ignition switch is turned ON.
Total Average Fuel Consumption
Y129630

·

Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN) since the counter was reset.

·

The display updates every 10 seconds.


Water Temperature Gauge
Y129631

The engine coolant temperature date are displayed with bar graph.
Average Vehicle Speed
Y129632

·

Displays the value that has been calculated by the meter ECU, which is based on the elapsed time and driven distance since the ignition switch was turned ON or since the counter was reset.

·

The display updates every 10 seconds.


Cruising Range
Y129633

Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch is turned ON.
Outside Temperature
Y129634

·

Displays the outside temperature.

·

The display updates every 3.84 second.


ECO Driving Indicator Zone Display
Y129635

Eco driving ratio based on acceleration is shown with a bar graph.
Dimming Mode Display
Y129645

Displays the combination meter brightness.



d.

Eco Driving Indicator

i.

The operating diagram of Eco Driving Indicator Light is as follows:

Y129637E01
0.833,0.271 1.323,0.698 0.49,0.427 10 false Large 0.813,2.906 1.302,3.333 0.49,0.427 10 false Small 0.479,1.635 1.406,1.979 0.927,0.344 10 false Acceleration 3.688,0.865 6.458,1.208 2.771,0.344 10 false Eco Driving Indicator Light will not Turn On 2.688,2.417 5.042,2.708 2.354,0.292 10 false Eco Driving Indicator Light Turns On* 3.417,3.135 4.344,3.479 0.927,0.344 10 false Vehicle Speed 1.76,3.135 2.188,3.448 0.427,0.313 10 false Slow 5.719,3.135 6.146,3.448 0.427,0.313 10 false Fast 0.115,3.448 3.094,3.792 2.979,0.344 10 false *: Will not turn on while the vehicle is stopped.


ii.

When the ECM, using information (such as vehicle speed, accelerator pedal depressed volume, engine speed signal (engine r/min data), and so on), calculates that the vehicle is driven in an Eco-friendly manner, it turns on Eco Driving Indicator Light and shows the bar graph of ECO Driving Indicator Zone Display within Zone of Eco driving.


iii.

When the ECM calculates that the acceleration exceeds Zone of Eco driving, it turns off ECO Driving Indicator Light and blinks the right side of Eco Driving Indicator Zone Display.


iv.

The operation of Eco Driving Indicator is as follows:

Models with Analog Type Combination Meter Assembly
Vehicle Condition ECO Driving Indicator Zone Display Eco Driving Indicator Light
Stopped
Y129639

Turns off
ECO Driving
Y129641

Turns on
Non-ECO Driving
Y129643

Turns off

Models with Optitron Type Combination Meter Assembly
Vehicle Condition ECO Driving Indicator Zone Display Eco Driving Indicator Light
Stopped
Y184570

Turns off
ECO Driving
Y184571

Turns on
Non-ECO Driving
Y184572

Turns off


v.

Eco Driving Indicator can be deactivated in the following ways: Eco Driving Indicator Light can be deactivated from Eco Driving Indicator Light customization display of the multi-information display.



e.

Front Seat Belt Warning Function

i.

When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the driver and front passenger seat belt buckle switches and the occupant detection sensor.


ii.

On models except models for G.C.C. countries, the buzzer sounds when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled. After 30 seconds, the sound changes for emphasis. The sound continues for 90 seconds. Once a buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch is turned off.


iii.

On models for G.C.C. countries, when the seat belt is unbuckled, the buzzer sounds 5 times 1.8 seconds after the ignition switch is turned on (IG). The buzzer sounds when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled. After 9.6 seconds, the sound changes for emphasis. The sound continues for 20 seconds. Once a buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch is turned off.

HINT:

Upon receiving a request from a user who cannot wear a seat belt for a special reason, the buzzer warning can be canceled using the Global TechStraem (GTS). For details, refer to the Repair Manual.



iv.

Occupant Detection Sensor (Except models for Korea)

·

The occupant detection sensor, which is enclosed in the seat cushion of the front passenger seat, is used to detect whether or not the front passenger seat is occupied.

·

This sensor consists of a construction in which 2 electrode sheets sandwich a spacer. When the occupant is seated, the electrode sheets come in contact with each other through the hole provided in the spacer portion, thus enabling the current to flow.

·

Thus, the sensor detects whether or not an occupant is seated in the front passenger seat.



v.

Occupant Detection Sensor (Models for Korea)

·

The occupant detection sensors are installed on brackets connecting the seat rail and the seat frame. The resistance values of these sensors, which vary in accordance with the distortion that acts on the brackets, are output to the occupant detection ECU.

·

The occupant detection ECU constantly monitors the weight on the front passenger seat, and makes a judgment in accordance with the signals from the occupant detection sensor and the state of the front passenger seat belt buckle switch.

·

The occupant detection ECU transmits the signals to the center airbag sensor assemby.




f.

Rear Passengers Seat Belt Reminder Function (Models with Rear Passengers Seat Belt Reminder Function)

Y190104C01
2.823,1 2.823,1.5 2.823,1.5 3.781,1.5 true 3.396,1.5 3.396,0.99 true 3.115,1.49 3.115,0.99 true 3.844,1.427 4.156,1.625 0.313,0.198 10 false *1
*1 Telltale Marker - -


i.

If the meter ECU receives an off signal from the rear door courtesy light switch assembly when the ignition switch is ON, a rear passenger seat belt reminder display is shown on the telltale light assembly. At this time, if the meter ECU receives an on signal from a rear seat belt buckle switch, it will extinguish the telltale light corresponding to the rear seat belt buckle switch which sent the on signal. In addition, the rear passenger seat belt reminder display will automatically turn off approximately 34 seconds after the display.


ii.

If any of the rear seat belts are released while the vehicle speed is above 20 km/h (12 mph), the rear passengers seat belt reminder illuminates and the buzzer is sounded. After 30 seconds, the sound change for emphasis. The sound continues for 90 seconds. Once the buzzer begins to sound, it will continue until the rear seat belt is buckled or the ignition switch is turned off.


iii.

The DISP switch installed on the steering pad switch can be used to show the rear passengers seat belt reminder display as required.




FAIL-SAFE


a.

Eco Driving Indicator

i.

When any of the following conditions are met, Eco Driving Indicator Light is turned off and ECO Driving Indicator Zone Display is stopped:

·

Engine Signal Malfunction

·

CAN Signal Malfunction