FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Cruise Control Main Switch | ON/OFF Button | Turns on/off the power to the cruise control system. |
| CANCEL Switch | A cancel signal can be output to the ECM through the operation of this switch. | |
| +RES Switch | The acceleration function and resume control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | |
| -SET Switch | The deceleration function and set control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | |
| Speed Sensors | Detects the vehicle speed and transmits a signal via the skid control ECU to the ECM. | |
| Throttle Body with Motor Assembly*1 | Throttle Control Motor | Adjusts the throttle valve to the limiter position in accordance with signals from the ECM. |
| Throttle Position Sensor | Transmits the throttle valve position information to the ECM. | |
| Stop Light Switch Assembly | Detects the depressing of the brake pedal and transmits a signal to the ECM and TCM*2. | |
| Park/Neutral Position Switch Assembly*3 | Detects the shift lever position and transmits a signal to the ECM. | |
| Combination Meter Assembly | Cruise Control Indicator Light | ·
Illuminates when the ON/OFF button has been pressed to turn the cruise control system on. ·
If the ECM detects a malfunction, this light illuminates in yellow*4 or turns off*5 to warn the driver. |
| Cruise control SET Indicator Light | Illuminates when the -SET switch on the cruise control main switch has been pressed to set the cruise control system. | |
| Multi-information Display*5 | ·
Displays a warning message to alert the driver in accordance with a signal sent by the ECM. ·
Displays a set speed when the vehicle speed is set. |
|
| Master Warning Light*2 | Displays a warning message to alert the driver in accordance with a signal provided by the ECM. | |
| ECM | ·
Controls the cruise control system in accordance with signals from the switches and sensors. ·
If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC). |
|
| Injector Assembly*6 | Adjusts the fuel injection volume based on the signals from the ECM or injector driver*8. | |
| Clutch Switch Assembly*7 | Detects the depressing of the clutch pedal and transmits a signal to the ECM. | |
| Injector Driver*8 | Receives signals from the ECM to control the injector. | |
| Transmission Floor Shift Assembly*3 | Transmission Control Switch | Detects the shift lever upward or downward position switch operation and transmits a signal to the ECM. |
| Shift Paddle Switch (Transmission Shift Switch Assembly)*9 | Detects the paddle shift switch operation and transmits a signal to the ECM. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression degree and outputs it to the ECM. | |
| Telltale Light Assembly | VSC OFF Switch | Enables the driver to select normal mode, TRC OFF mode or VSC OFF mode. |
| TCM*2 | Controls the automatic transaxle in accordance with signals from the ECM. | |
*1: Models with gasoline engine
*2: Models with U660F automatic transaxle
*3: Models with automatic transaxle or CVT
*4: Models with analog type combination meter assembly
*5: Models with Optitron type combination meter assembly
*6: Models with diesel engine
*7: Models with manual transaxle
*8: Models with 2AD-FHV engine or 2AD-FTV engine
*9: Models with paddle shift
| Component | Function | |
|---|---|---|
|
*1: Models with diesel engine *2: Models with gasoline engine *3: Models with manual transaxle *4: Models with CVT |
||
| Steering Pad Switch Assembly | Speed Limiter Main Switch | Turns on/off the power to the speed limiter control mode. |
| Cruise Control Main Switch | ON/OFF Button | Turns on/off the power to the cruise control system. |
| CANCEL Switch | A cancel signal can be output to the ECM through the operation of this switch. | |
| +RES Switch | The acceleration function and resume control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | |
| -SET Switch | The deceleration function and set control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | |
| Speed Sensors | Detects the vehicle speed and transmits a signal via the skid control ECU to the ECM. | |
| Injector Assembly*1 | Adjusts the fuel injection volume based on the signals from the ECM. | |
| Throttle Body with Motor Assembly*2 | Throttle Control Motor | Adjusts the throttle valve to the limiter position in accordance with signals from the ECM. |
| Throttle Position Sensor | Transmits the throttle valve position information to the ECM. | |
| Accelerator Pedal Sensor Assembly | Detects whether the accelerator pedal is in the kick down mode and transmits signals to the ECM. | |
| Clutch Switch Assembly*3 | Detects the depressing of the clutch pedal and transmits a signal to the ECM. | |
| Park/Neutral Position Switch*4 | Detects the shift position and transmits a signal to ECM. | |
| Combination Meter Assembly | Speed Limiter Main Indicator Light | Illuminates when the speed limiter main switch has been pressed to turn the speed limiter control mode on. If the ECM detects a malfunction, this light turns off to warn the driver. |
| Multi-information Display | Shows the state of the speed limiter control mode. Displays a warning message when a malfunction has occurred to inform the driver. | |
| ECM | ·
Controls the speed limiter control mode in accordance with signals from the switches and sensors. ·
If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC). |
|
FUNCTION
The cruise control system has the following functions:
| Function | Outline | |
|---|---|---|
| Set Control | When the ON/OFF button is turned on and the cruise control main switch is pressed to the -SET direction and released, the ECM stores the vehicle speed in the memory and continues to control the vehicle at that speed. The set speed can be between 40 km/h (25 mph) and 200 km/h (125 mph). Furthermore, when the cruise control system is running, the cruise control SET indicator light on the combination meter assembly illuminates. | |
| Coast Control | Models with Diesel Engine | When the cruise control main switch is kept pushed to the -SET direction while the cruise control system is running, the ECM decreases the fuel injection volume by regulating the 4 injectors. As the vehicle continues to decelerate, the ECM stores the vehicle speed at the time the cruise control main switch is released. From then on, the ECM continues to control the vehicle at that speed. |
| Models with Gasoline Engine | When the cruise control main switch is kept pushed to the -SET direction while the cruise control system is running, the throttle control motor is energized in the throttle closing direction, and the vehicle keeps decelerating. The ECM stores the vehicle speed when the cruise control main switch is released. From then on, the ECM controls the vehicle speed at that speed constantly. | |
| Tap-down Control | ·
When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered approx. 1 km/h (1 mph) each time by operating the cruise control main switch in the -SET direction quickly within approx. 0.6 seconds.*1 ·
When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered approx. 1.6 km/h (1 mph) each time by operating the cruise control main switch in the -SET direction quickly within approx. 0.6 seconds.*1 |
|
| Accelerator Control | Models with Diesel Engine | When the cruise control main switch is kept pushed to the +RES side while the cruise control system is running, the ECM increases the fuel injection volume by regulating the 4 injectors. As the vehicle continues to accelerate, the ECM stores the vehicle speed at the time the cruise control main switch is released. From then on, the ECM continues to control the vehicle at that speed. |
| Models with Gasoline Engine | When the cruise control main switch is kept pushed to the +RES direction while the cruise control system is running, the throttle control motor is energized in the throttle opening direction. The vehicle keeps accelerating and the ECM stores the vehicle speed when the cruise control main switch is released. From then on, the ECM controls the vehicle speed at that speed constantly. | |
| Tap-up Control | ·
When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased approx. 1 km/h (1 mph) each time by operating the cruise control main switch in the +RES direction quickly within approx. 0.6 seconds.*1 ·
When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased approx. 1.6 km/h (1 mph) each time by operating the cruise control main switch in the +RES direction quickly within approx. 0.6 seconds.*2 |
|
| Low Speed Limit Control | The low speed limit is the lowest speed that the cruise control system can be set to and is set at approx. 40 km/h (25 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control system is running, the cruise control system is canceled automatically. | |
| Resume Control | After the cruise control system is canceled for any reason other than a malfunction or operating the ON/OFF button, the mode can be resumed and controlled at the set speed by operating the cruise control main switch in the +RES direction when the vehicle speed returns above the low speed limit (approx. 40 km/h [25 mph]). | |
| Shift Down Control*3 | When the vehicle is traveling uphill using cruise control, automatic transaxle control may cause the transaxle to shift down. During shift down control, when the end of uphill travel is determined, the transaxle will shift up after a certain period of time. When the transaxle shifts down during the accelerator control or the resume control, the transaxle will shift up after the accelerator control or the resume control ends. | |
| Manual Cancel Control | If any of the following conditions is met, cruise control is canceled accordingly. However, the set speed remains in the memory:
·
On signal is sent from the stop light switch assembly (the brake pedal is depressed). ·
Off signal is sent from the clutch switch assembly (the clutch pedal is depressed).*4 ·
Shift lever is moved from D, S*5 or M*6 to another position.*7 ·
1st, 2nd or 3rd range is selected in the D mode position by shift paddle switch (transmission shift switch assembly) operation.*8 ·
1st, 2nd or 3rd range is selected in the S*5 or M*6 mode position.*7 ·
On signal is sent from the CANCEL switch. ·
ON-OFF button is turned off (the set speed is not stored). |
|
| Automatic Cancel Control | When any of the following conditions occurs while the cruise control system is running, the set speed in the memory is cleared to cancel the cruise control system. Furthermore, the cruise control indicator light illuminates in yellow*9 or turns off*10 until the ON/OFF button is turned off, and the operation of the cruise control system is disabled until the ON/OFF button is turned on again.
·
The stop light switch assembly has an open or short circuit. ·
The vehicle speed signal is abnormal. |
|
| When any of the following conditions occurs while the cruise control system is running, the set speed in the memory is cleared to cancel the cruise control system. Furthermore, the operation of the cruise control system is disabled until the ON/OFF button is turned on again.
·
The ETCS-i has a malfunction.*11 ·
The common-rail type diesel EFI system has a malfunction.*12 |
||
| When any of the following conditions occurs while the cruise control system is running, the set speed in the memory is cleared to cancel the cruise control system. Furthermore, the cruise control indicator light illuminates in yellow*9 or turns off*10 until the ON/OFF button is turned off, and the operation of the cruise control system is disabled until the ignition switch is turned off.
·
The stop light switch input signal is abnormal. ·
The cancel circuit has a malfunction. |
||
| When the following condition occurs while the cruise control system is running, the cruise control system is canceled. The cruise control system can be resumed at the set speed by operating the cruise control main switch in the -SET or +RES direction providing that the vehicle speed is above the low speed limit (approx. 40 km/h [25 mph]).
·
The vehicle speed falls below the low speed limit (approx. 40 km/h [25 mph]). The set speed in the memory is maintained. |
||
| When the following condition occurs while the cruise control system is running, the cruise control system is canceled. The cruise control system can be resumed at the set speed by operating the cruise control main switch in the -SET direction providing that the vehicle speed is above the low speed limit (approx. 40 km/h [25 mph]).
·
The vehicle speed drops more than 16 km/h (10 mph) below the set speed. The set speed in the memory is cleared. |
||
| Other Cancel Control | ·
If any of the following conditions occur during cruise control driving, the cruise control is canceled. However, the set speed remains in the memory. ·
The VSC system is activated. ·
The TRC system is activated for a period of time. ·
The VSC or TRC system is turned off by pressing the VSC OFF switch. ·
When the ignition switch is turned off, the set speed is not stored in the memory. |
|
*1: Except models with 2WW engine
*2: Models with 2WW engine
*3: Models with automatic transaxle
*4: Models with manual transaxle
*5: Models with U760E or U760F automatic transaxle
*6: Models with U660F automatic transaxle or CVT
*7: Models with automatic transaxle or CVT
*8: Models with shift paddle
*9: Models with analog type combination meter assembly
*10: Models with Optitron type combination meter assembly
*11: Models with gasoline engine
*12: Models with diesel engine
| Function | Outline | |
|---|---|---|
| Set Control | When the driver turns on the speed limiter main switch, the speed limiter main indicator light will illuminate in the combination meter assembly. In this state, when the cruise control switch is pressed in the -SET direction, the system will memorize the vehicle speed that existed prior to the operation of the cruise control switch as a limit speed, and display the limit speed on the combination meter assembly. (If the cruise control switch is pressed in the -SET direction while the vehicle is being driven at 30 km/h [20 mph] or less, or while the vehicle is stopped, the system will memorize the limit speed as being approx. 30 km/h [20 mph]). | |
| Constant Speed Control | Models with Diesel Engine | When the speed limiter control mode is on, the ECM will compare the actual vehicle speed with the limit speed. If the actual vehicle speed is greater than the limit speed, the ECM will control the 4 injectors in order to reduce the fuel injection volume. Thus, the system reduces the actual vehicle speed to the limit speed. |
| Models with Gasoline Engine | When the speed limiter control mode is on, the ECM will compare the actual vehicle speed with the limit speed. If the actual vehicle speed is greater than the limit speed, the ECM will control the throttle control motor in the closing direction. Thus, the system reduces the actual vehicle speed to the limit speed. | |
| Coast Control | If the driver continues to press the cruise control main switch in the -SET direction, the system will reduce the limit speed in 5 km/h (5 mph) increments. The instant the driver releases the cruise control switch, that speed will be rendered as the set speed. | |
| Tap-down Control | If the driver presses the cruise control switch momentarily (approx. 0.6 seconds) in the -SET direction, the system will reduce the limit speed by 1 km/h (1 mph) with each press of the switch. | |
| Accelerator Control | If the driver continues to press the cruise control switch in the +RES direction, the system will increase the limit speed in 5 km/h (5 mph) increments. The instant the driver releases the cruise control switch, that speed will be rendered as the limit speed. | |
| Tap-up Control | If the driver presses the cruise control main switch momentarily (approx. 0.6 seconds) in the +RES direction, the system will increase the limit speed by 1 km/h (1 mph) with each press of the switch. | |
| Override Control | While driving the vehicle with the speed limiter control mode on, if the driver fully depresses the accelerator pedal, the ECM will detect that the accelerator pedal position sensor is in the kick down mode. Then, the ECM will recognize this to be the driver's acceleration requirement, and allow the vehicle to accelerate higher than the limit speed. After the acceleration, when the vehicle speed gets below the limit speed, this function will resume effecting limit speed control on the vehicle speed. | |
| Cancel Control | While the vehicle is being driven with the speed limiter control mode on, if any one of the following signals is input into the ECM, the system will cancel the speed limiter control mode:
·
CANCEL switch on signal (The driver has pressed the cruise control main switch in the CANCEL direction.) ·
Speed limiter main switch off signal (Deletes the limit speed.) ·
ON/OFF button on signal (Transfers to the constant speed control mode, turns off the speed limiter main indicator light, and deletes the limit speed.) |
|
| Resume Control | After turning the CANCEL switch on to turn the speed limiter control mode off, if the driver pushes the cruise control main switch in the +RES direction, the system will limit the vehicle speed at the limit speed that existed at the time of cancellation. | |
DIAGNOSIS
If a malfunction occurs in the cruise control system, the ECM cancels the cruise control system. The ECM illuminates the cruise control indicator light in yellow*1 or turns off the cruise control indicator light*2 to inform the driver of a malfunction. Furthermore, the ECM displays a warning message on the multi-information display.*2 At this time, the ECM memorizes the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC). For details on the DTC, refer to the Repair Manual.
*1: Models with analog type combination meter assembly
*2: Models with Optitron type combination meter assembly