Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2016.08
NM3090E _51 Engine / Hybrid System _008644 3ZR-FAE ENGINE CONTROL _0048051 SFI SYSTEM DE DETAILS F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  DETAILS  STARTER CONTROL (CRANKING HOLD FUNCTION)  


OPERATION


a.

Models with Continuously Variable Transaxle (CVT)

i.

When first starting the engine, if the certification ECU (smart key ECU assembly) receives a start signal from the engine switch, the certification ECU (smart key ECU assembly) sends an operation signal to the ST No. 1 relay via the park/neutral position switch assembly when the shift lever is in P or N and the engine stop and start ECU sends an operation signal to the ST No. 2 relay to operate the starter assembly. At this time, the certification ECU (smart key ECU assembly) turns the ACC relay operation signal (ACCD) off to prevent flickering of the meter, clock and audio systems.


ii.

When starting the engine during idling stop control, the engine stop and start ECU sends operation signals to the ST No. 1 relay and ST No. 2 relay according to the vehicle condition to operate the starter assembly.


iii.

While the engine is cranking, the certification ECU (smart key ECU assembly) and/or engine stop and start ECU continues to send an operation signal to the starter relay until it has been detected that the engine has started successfully. Whether the engine has started successfully is determined by the certification ECU (smart key ECU assembly) and ECM, and once it has been determined that the engine has started successfully, the signal output from the certification ECU (smart key ECU assembly) and/or engine stop and start ECU to the starter relay is stopped.


iv.

The crank hold time and engine speed when it has been determined that the engine has started successfully are determined according to the engine coolant temperature.

W130866E04
6.094,1.656 7.021,2.427 0.927,0.771 10 false Engine Stop and Start ECU 4.5,0.896 5.833,2.042 1.333,1.146 10 false Park/Neutral Position Switch Assembly 0.146,0.344 1.052,1.146 0.906,0.802 10 false Engine Switch (Push Start Switch) 1.625,1.01 2.385,2.583 0.76,1.573 10 false Certification ECU (Smart Key ECU Assembly) 3.354,2.771 3.781,3.333 0.427,0.563 10 false ACC Relay 0.979,3.594 1.792,4.188 0.813,0.594 10 false CAN (Bus 2) 2.229,3.75 3.135,4.135 0.906,0.385 10 false Engine Speed 4.51,4.281 5.104,4.938 0.594,0.656 10 false ST No. 1 Relay 6.104,4.26 6.698,4.917 0.594,0.656 10 false ST No. 2 Relay 1.833,4.958 2.74,5.344 0.906,0.385 10 false ECM 4.375,5.688 5.49,6.083 1.115,0.396 10 false Starter Assembly 0.115,4.844 1.229,5.531 1.115,0.688 10 false Stop Light Switch Assembly 0.115,5.583 1.042,6.313 0.927,0.729 10 false Crank Position Sensor 2.271,6.479 4.521,6.865 2.25,0.385 10 false Engine Coolant Temperature Sensor



b.

Models with manual transaxle

i.

When first starting the engine, if the certification ECU (smart key ECU assembly) receives a start signal from the engine switch, the certification ECU (smart key ECU assembly) sends an operation signal to the starter relay via the clutch start switch assembly when the clutch pedal is depressed to operate the starter assembly. At this time, the certification ECU (smart key ECU assembly) turns the ACC relay operation signal (ACCD) off to prevent flickering of the meter, clock and audio systems.


ii.

When starting the engine during idling stop control, the engine stop and start ECU sends operation signals to the starter relay according to the vehicle condition to operate the starter assembly.


iii.

While the engine is cranking, the certification ECU (smart key ECU assembly) and/or engine stop and start ECU continues to send an operation signal to the starter relay until it has been detected that the engine has started successfully. Whether the engine has started successfully is determined by the certification ECU (smart key ECU assembly) and ECM, and once it has been determined that the engine has started successfully, the signal output from the certification ECU (smart key ECU assembly) and/or engine stop and start ECU to the starter relay is stopped.


iv.

The crank hold time and engine speed when it has been determined that the engine has started successfully are determined according to the engine coolant temperature.

W130904E02
0.135,0.344 1.052,1.375 0.917,1.031 10 false Engine Switch (Push Start Switch) 1.635,1.208 2.406,2.625 0.771,1.417 10 false Certification ECU (Smart Key ECU) 4.5,1.042 5.74,1.875 1.24,0.833 10 false Clutch Start Switch Assembly 3.365,2.813 3.781,3.563 0.417,0.75 10 false ACC Relay 2.26,3.75 3.458,4.24 1.198,0.49 10 false Engine Speed 0.917,3.677 1.792,4.125 0.875,0.448 10 false CAN (Bus 2) 0.104,4.771 1.229,5.51 1.125,0.74 10 false Stop Light Switch Assembly 0.188,5.583 1.104,6.229 0.917,0.646 10 false Crank Position Sensor 2.198,6.479 5.01,6.885 2.813,0.406 10 false Engine Coolant Temperature Sensor 4.021,5.708 5.271,6.031 1.25,0.323 10 false Starter Assembly 4.771,4.365 5.25,5.073 0.479,0.708 10 false Starter Relay 6.26,1.323 6.917,2.896 0.656,1.573 10 false Engine Stop and Start ECU 1.833,5.156 2.344,5.708 0.51,0.552 10 false ECM