Home › Engine / Hybrid System › 1AD-FTV EMISSION CONTROL › EGR VALVE › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008371 1AD-FTV EMISSION CONTROL _0046701 EGR VALVE A

1AD-FTV EMISSION CONTROL  EGR VALVE  INSTALLATION  


PROCEDURE

Hide 25800 1.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A273028C01
1.75,0.417 2.042,0.135 2.042,0.135 2.208,0.135 true 2.25,0.042 2.563,0.198 0.313,0.156 10 *1
*1 Protrusion


Install a new gasket.

NOTICE:

Make sure the protrusion of the gasket is facing upward as shown in the illustration.



b.

Install the electric EGR control valve assembly.


Hide 25602 2.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY

a.

Install a new gasket to the No. 2 EGR pipe sub-assembly.


b.

Install a new gasket to the electric EGR control valve assembly.


c.
A273029C01
0.635,1.854 0.948,2.01 0.313,0.156 10 *1 3.104,0.448 3.26,0.646 0.156,0.198 10 A 0.104,0.281 0.26,0.479 0.156,0.198 10 B 2.219,1.573 2.375,1.771 0.156,0.198 10 A 1,0.26 1.156,0.458 0.156,0.198 10 B 0.417,1.385 0.573,1.583 0.156,0.198 10 B
*1 Nut


Temporarily install the No. 2 EGR pipe sub-assembly with the 3 bolts and 2 nuts.

Bolt Length:
Item Specified Condition
Bolt A 25 mm (0.984 in.)
Bolt B 70 mm (2.76 in.)



d.

Tighten the 2 bolts labeled A shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.

Tighten the bolt and 2 nuts labeled B shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


f.

Connect the electric EGR control valve connector.


Hide 16296 3.CONNECT NO. 8 WATER BY-PASS HOSE

a.

Connect the No. 8 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


Hide 16295 4.CONNECT NO. 7 WATER BY-PASS HOSE

a.

Connect the No. 7 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


Hide 25625 5.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket with the 3 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Connect the 2 connectors and attach the 2 wire harness clamps.


Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER

Hide 10.PERFORM ELECTRIC EGR CONTROL VALVE FULLY CLOSED POSITION LEARNING

HINT:

Be sure to turn off the ignition switch before performing this operation.


a.

Turn the ignition switch to ON.


b.

Turn the ignition switch off and wait 30 seconds.

HINT:

The fully closed position of the electric EGR control valve assembly is learned when the ignition switch is turned off.