Home › Engine / Hybrid System › 2AD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM3090E _51 Engine / Hybrid System _008372 2AD-FTV ENGINE MECHANICAL _0046712 ENGINE UNIT G

2AD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

a.
A120616
0.646,1.729 0.76,1.896 0.115,0.167 10 false 1 0.823,1.729 0.938,1.896 0.115,0.167 10 false 2 1,1.729 1.115,1.896 0.115,0.167 10 false 3 1.177,1.729 1.292,1.896 0.115,0.167 10 false 4 1.354,1.729 1.469,1.896 0.115,0.167 10 false 5 1.542,1.729 1.656,1.896 0.115,0.167 10 false 6 2.917,1.729 3.094,1.896 0.177,0.167 10 false 16 1.698,1.083 2.01,1.24 0.313,0.156 10 false *1
*1 Measuring Area


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 16 links.

Maximum chain elongation:

144.3 mm (5.68 in.)


NOTICE:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the chain sub-assembly.


Hide 13540 2.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A203730
2.052,1.292 2.281,1.521 2.281,1.521 2.323,1.521 false 1.75,1.708 1.948,1.833 1.948,1.833 2.031,1.833 false 2.083,1.75 2.396,1.979 0.313,0.229 10 *2 2.365,1.448 2.635,1.667 0.271,0.219 10 *1
*1 Plunger
*2 Stopper Plate


Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.


Hide 13523 3.INSPECT CAMSHAFT TIMING SPROCKET

a.

Wrap the chain sub-assembly around the camshaft timing sprocket.


b.
A203731

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket with chain diameter:

132.6 mm (5.22 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.

If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing sprocket.



Hide 13521 4.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Wrap the chain around the crankshaft timing sprocket.


b.
A203732

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket with chain diameter:

69.1 mm (2.70 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.


Hide 13559 5.INSPECT CHAIN TENSIONER SLIPPER

a.
A203774

Using a vernier caliper, measure the tensioner slipper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the chain tensioner slipper.


Hide 13561 6.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A203775

Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 1 chain vibration damper.


Hide 17111 7.INSPECT INTAKE MANIFOLD

a.
A130406

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the intake manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the intake manifold.


Hide 17141 8.INSPECT EXHAUST MANIFOLD

a.
A130405

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.40 mm (0.0157 in.)


If the warpage is more than the maximum, replace the exhaust manifold.


Hide 13511 9.INSPECT CAMSHAFT

a.

Check the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

37.559 to 37.759 mm (1.4787 to 1.4866 in.)


Minimum cam lobe height:

37.559 mm (1.4787 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard journal diameter:

26.969 to 26.985 mm (1.0618 to 1.0624 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13512 10.INSPECT NO. 2 CAMSHAFT

a.

Check the No. 2 camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the No. 2 camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

38.270 to 38.470 mm (1.5067 to 1.5146 in.)


Minimum cam lobe height:

38.270 mm (1.5067 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard journal diameter:

26.969 to 26.985 mm (1.0618 to 1.0624 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 11.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft bearing caps and camshaft journals.


b.

Place the camshafts on the cylinder head sub-assembly.


c.
A111297
1.552,1.229 1,0.375 1,0.375 0.802,0.375 true 0.573,0.271 0.885,0.427 0.313,0.156 10 *1
*1 Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A111298

Measure the Plastigage at its widest point.

Standard oil clearance:

0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum oil clearance:

0.062 mm (0.00244 in.)


If the camshaft oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.


g.

Completely remove the Plastigage.


Hide 11101A 12.INSPECT CYLINDER HEAD SET BOLT

a.
A206111
2.042,0.708 2.354,0.865 0.313,0.156 10 false *1 1.469,1.51 1.781,1.667 0.313,0.156 10 false *a
*1 Measuring Area
*a 156 mm (6.14 in.)


Using a vernier caliper, measure the minimum diameter of the elongated thread in the measuring area.

Standard outside diameter:

11.8 to 12.0 mm (0.465 to 0.472 in.)


Minimum outside diameter:

11.2 mm (0.441 in.)


HINT:

If a visual check reveals no excessively thin areas, check the center of the cylinder head set bolt (see illustration) and find the area that has the smallest diameter.


If the diameter is less than the minimum, replace the cylinder head set bolt.


Hide 13801 13.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A201831

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 14.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign objects.

·

Use only clean engine oil.



a.

Place the valve lash adjuster assembly into a container full of new engine oil.


b.

Insert SST tip into the valve lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  

A271553
1.125,1.302 1.469,1.302 false 1.052,1.844 1.51,1.844 false 1.021,2.177 1.594,2.177 false 1.104,2.396 1.594,2.396 false 2.625,0.823 3.208,0.823 false 2.385,2.188 2.885,2.188 false 1.229,0.76 1.458,0.76 false 1.01,1.073 1.49,1.073 false 4.927,1.635 5.448,1.135 5.448,1.135 5.646,1.135 false 1.531,0.99 1.844,1.146 0.313,0.156 10 false *1 1.531,1.219 1.844,1.375 0.313,0.156 10 false *2 1.552,1.75 1.865,1.906 0.313,0.156 10 false *3 1.646,2.073 1.958,2.229 0.313,0.156 10 false *4 1.635,2.292 1.948,2.448 0.313,0.156 10 false *5 0.844,0.167 1.156,0.323 0.313,0.156 10 false *a 2.323,0.167 2.635,0.323 0.313,0.156 10 false *b 1.51,0.688 1.969,0.885 0.458,0.198 10 false SST 3.26,0.74 3.719,0.938 0.458,0.198 10 false SST 5.698,1.052 6.156,1.25 0.458,0.198 10 false SST 2.99,2.104 3.302,2.26 0.313,0.156 10 false *4
*1 Taper Part *2 Plunger
*3 Lower Pressure Chamber *4 Check Ball
*5 High Pressure Chamber - -
*a CORRECT *b INCORRECT



c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding air, remove SST. Then quickly and firmly press the plunger repeatedly with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster assembly with a new one.


Hide 15.INSPECT ENGINE BALANCER ASSEMBLY THRUST CLEARANCE

a.
A203796

Using a dial indicator, measure the thrust clearance while moving the balance shaft back and forth.

Standard thrust clearance:

0.07 to 0.11 mm (0.00303 to 0.00433 in.)


Maximum thrust clearance:

0.11 mm (0.00433 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.


Hide 13620B 16.INSPECT ENGINE BALANCER ASSEMBLY BACKLASH

a.
A203779

Fix the No. 3 balance shaft driven gear in place, and then using a dial indicator, measure the backlash of the No. 1 balance shaft driven gear and No. 3 balance shaft driven gear as shown in the illustration.

Standard backlash:

0.020 to 0.092 mm (0.000787 to 0.00362 in.)


Maximum backlash:

0.114 mm (0.0045 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.