Home › Engine / Hybrid System › 1AD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008376 1AD-FTV INTAKE / EXHAUST _0046750 EXHAUST MANIFOLD W/ TURBOCHARGER A

1AD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

For turbocharger sub-assembly:

i.
A263963
0.74,3.604 1.052,3.76 0.313,0.156 10 *a 2,3.448 2.313,3.604 0.313,0.156 10 *b 2.01,4.021 2.323,4.177 0.313,0.156 10 *c
*a 32 mm (1.26 in.)
*b 20 mm (0.787 in.)
*c 10 mm (0.394 in.)


Using an E8 "TORX" wrench, install the 3 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A291347
0.635,2.604 0.948,2.76 0.313,0.156 10 *a 1.49,2.271 1.802,2.427 0.313,0.156 10 *b 0.646,3.917 0.958,4.073 0.313,0.156 10 *c 1.49,3.781 1.802,3.938 0.313,0.156 10 *d 1.5,4.135 1.813,4.292 0.313,0.156 10 *e 1.49,2.99 1.802,3.146 0.313,0.156 10 *b 1.094,1.979 1.25,2.177 0.156,0.198 10 A 0.427,0.417 0.583,0.615 0.156,0.198 10 A 1.167,1.219 1.323,1.417 0.156,0.198 10 A 1.094,3.427 1.25,3.625 0.156,0.198 10 B 2.323,0.865 2.479,1.063 0.156,0.198 10 B 2.083,0.552 2.24,0.75 0.156,0.198 10 B 0.948,0.198 1.104,0.396 0.156,0.198 10 B
*a 43 mm (1.69 in.)
*b 16 mm (0.630 in.)
*c 24.5 mm (0.965 in.)
*d 12 mm (0.472 in.)
*e 9.0 mm (0.354 in.)


Install the 2 stud bolts labeled A shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


iii.

Using an E5 "TORX" wrench, install the 3 stud bolts labeled B shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iv.
A263964
0.646,3.531 0.958,3.688 0.313,0.156 10 *a 1.917,2.979 2.229,3.135 0.313,0.156 10 *b 1.906,4.125 2.219,4.281 0.313,0.156 10 *c
*a 47 mm (1.85 in.)
*b 14 mm (0.551 in.)
*c 15 mm (0.591 in.)


Using an E8 "TORX" wrench, install the stud bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.
A291348
0.552,2.531 0.865,2.688 0.313,0.156 10 *a 1.958,2.198 2.271,2.354 0.313,0.156 10 *b 1.958,2.938 2.271,3.094 0.313,0.156 10 *b
*a 43 mm (1.69 in.)
*b 16 mm (0.630 in.)


For exhaust manifold:

Install the stud bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD AND TURBOCHARGER SUB-ASSEMBLY

a.
A273051
1.25,2.333 1.417,2.333 1.417,2.333 1.417,2.667 false 1.75,2.333 1.583,2.333 1.583,2.333 1.583,2.833 true 1.792,2.24 2.104,2.396 0.313,0.156 10 *1 1.094,2.229 1.406,2.385 0.313,0.156 10 *2 1.625,0.365 1.781,0.563 0.156,0.198 10 A 2.229,0.375 2.385,0.573 0.156,0.198 10 A
*1 Collar
*2 Groove


Temporarily install a new gasket, the exhaust manifold, and the 2 collars with 2 new nuts labeled A. Tighten the nuts until the mating surface of the exhaust manifold contacts the cylinder head.


b.

Temporarily install the 6 collars with 6 new nuts.

HINT:
·

When installing the collars, pay attention to the mounting orientation. The ring groove of the collar should be on the outside. Refer to the illustration.

·

Do not fully tighten the nuts as doing so may result in misalignment of the exhaust manifold.




c.

Install a new gasket and the turbocharger sub-assembly with 3 new nuts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


d.
A273052
0.302,0.833 0.635,0.833 false 0.271,1.146 0.604,1.146 false 1.021,1.208 1.135,1.604 1.135,1.604 1.302,1.604 false 0.156,0.74 0.469,0.896 0.313,0.156 10 *1 0.104,1.052 0.417,1.208 0.313,0.156 10 *2 1.344,1.51 1.656,1.667 0.313,0.156 10 *2 1.938,0.771 2.094,0.969 0.156,0.198 10 A
*1 New Turbocharger Stay
*2 Collar


Install the 2 collars and a new turbocharger stay with 2 new nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Do not reuse the turbocharger stay.

·

When installing the turbocharger stay, be sure to tighten the nut labeled A first.




e.

Tighten the 8 nuts of the exhaust manifold.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 15474 3.INSTALL TURBO OIL OUTLET PIPE

a.

Install a new gasket and the turbo oil outlet pipe with the 3 nuts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


b.

Connect the turbo oil outlet pipe and a new gasket with the union bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 16267 4.INSTALL NO. 3 WATER BY-PASS HOSE

a.

Install the No. 3 water by-pass hose to the turbo oil outlet pipe and No. 1 water by-pass pipe, and slide the 2 clamps to secure the hose.


Hide 25707 5.INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 2 vacuum transmitting pipe sub-assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the 2 vacuum transmitting hoses.


Hide 1723A 6.INSTALL TURBOCHARGER WIRE

a.

Install the turbocharger wire and attach the 3 wire harness clamps.


b.

Connect the 2 connectors to the turbocharger sub-assembly.


Hide 15476 7.INSTALL NO. 2 TURBO OIL OUTLET PIPE

a.

Install a new gasket and the No. 2 turbo oil outlet pipe with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 15474A 8.INSTALL TURBO OIL OUTLET HOSE

a.

Install the turbo oil outlet hose to the turbo oil outlet pipe and No. 2 turbo oil outlet pipe, and slide the 2 clamps to secure the hose.


Hide 17271 9.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator with the 2 bolts.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)


Hide 25601L 10.INSTALL EGR COOLER WITH PIPE ASSEMBLY

Hide 11.PERFORM TURBOCHARGER INITIALIZATION