Home › Engine / Hybrid System › 2AD-FHV LUBRICATION › OIL AND OIL FILTER
RM3090E _51 Engine / Hybrid System _008384 2AD-FHV LUBRICATION _0046773 OIL AND OIL FILTER A

2AD-FHV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the clip and open the oil pan drain service cover.


c.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


d.

Install a new gasket and the oil pan drain plug.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


e.

Close the oil pan drain service cover and install the clip.


Hide 2.REMOVE OIL FILTER ELEMENT

a.
A273057
2.229,1.51 2.813,1.281 2.813,1.281 2.979,1.281 true 0.906,0.708 1.573,0.375 1.573,0.375 1.74,0.375 true 1.771,0.281 2.083,0.438 0.313,0.156 10 *1 3.01,1.188 3.323,1.344 0.313,0.156 10 *2
*1 Oil Filter Drain Pipe
*2 Hose


Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.


b.

Remove the clip and open the oil filter element service cover.


c.
A264004

Remove the oil filter drain plug.


d.

Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.


e.
A271745
2.667,1 1.823,1 true 2.667,1.333 2.5,1.333 2.5,1.333 1.323,1.573 true 2.667,1.833 1.083,1.833 true 2.698,0.917 3.01,1.073 0.313,0.156 10 *1 2.698,1.24 3.01,1.396 0.313,0.156 10 *2 2.708,1.74 3.021,1.896 0.313,0.156 10 *3
*1 Oil Filter Cap
*2 O-Ring
*3 Oil Filter Drain Pipe


Install the oil filter drain pipe to the oil filter cap and drain the engine oil into a container.


f.

Remove the oil filter drain pipe.


g.

Apply a light coat of engine oil to a new O-ring and install the O-ring to the oil filter drain plug.


h.

Install the oil filter drain plug to the oil filter cap.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


i.
A264005
1.646,2.125 2.729,2.125 true 2.76,2.031 3.219,2.229 0.458,0.198 10 SST

Using SST, remove the oil filter cap.

SST
09228-06501  


j.
A263994
2.083,0.667 2.917,0.667 true 2.344,1.177 2.927,1.177 true 2.938,0.573 3.25,0.729 0.313,0.156 10 *1 2.958,1.083 3.271,1.24 0.313,0.156 10 *2
*1 Oil Filter Element
*2 O-Ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the oil filter cap O-ring groove.



Hide 3.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.
A268595
2.927,1.177 3.177,1.677 3.177,1.677 3.177,1.854 true 1.427,1.073 1.677,1.573 1.677,1.573 1.677,1.75 true 1.604,1.76 1.917,1.917 0.313,0.156 10 *1 0.906,1.813 1.219,1.969 0.313,0.156 10 *a 2.448,1.813 2.76,1.969 0.313,0.156 10 *b 3.104,1.865 3.417,2.021 0.313,0.156 10 *1
*1 O-Ring
*a CORRECT
*b INCORRECT


Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.

Check and clean the oil filter installation surface.


g.
A271750
0.667,2.083 1.25,2.083 true 2.5,1.833 2.917,1.833 true 2.573,1.229 2.906,0.979 2.906,0.979 3.073,0.979 true 2.625,0.417 3.042,0.417 true 2.938,1.729 3.25,1.885 0.313,0.156 10 *1 3.104,0.875 3.417,1.031 0.313,0.156 10 *2 3.063,0.313 3.375,0.469 0.313,0.156 10 *3 3.083,1.365 3.396,1.521 0.313,0.156 10 *a 0.375,1.979 0.833,2.177 0.458,0.198 10 SST
*1 Oil Filter Cap
*2 O-Ring
*3 Oil Filter Bracket
*a No Gap


Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



h.

Close the oil filter element service cover and install the clip.


Hide 4.ADD ENGINE OIL

a.

Add new engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
ACEA C2 - 0W-30
- 5W-30


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
Drain and refill with oil filter change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)



Hide 5.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.