Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) U

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  TERMINALS OF ECM  


CHECK ECM


A194498
2.521,0.24 2.917,0.479 0.396,0.24 5.521,0.24 5.917,0.479 0.396,0.24 2.594,0.302 2.875,0.458 0.281,0.156 10 B76 5.604,0.292 5.885,0.438 0.281,0.146 10 A61

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard voltage of each ECM terminal is shown in the table below.

In the table, first follow the information in "Condition". Look at "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown in "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-2 (BATT) - B76-109 (E1) W - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A61-25 (IGSW) - B76-109 (E1) B - BR Ignition switch Ignition switch ON 11 to 14 V
A61-1 (+B) - B76-109 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
A61-20 (+B2) - B76-109 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
A61-45 (MREL) - B76-109 (E1) B - BR EFI MAIN relay Ignition switch ON 11 to 14 V
2 seconds elapsed after ignition switch off 0 to 1.5 V
A61-44 (IREL) - B76-109 (E1) R - BR EDU relay Ignition switch ON 0 to 1.5 V
B76-58 (GREL) - B76-109 (E1) B - BR Glow plug relay Cranking 11 to 14 V
Idling (10 minutes or more after engine start) 0 to 1.5 V
A61-53 (VPA) - A61-56 (EPA) Y - W Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.0 to 4.6 V
A61-54 (VPA2) - A61-58 (EPA2) P - R Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 0.9 to 2.3 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 5.0 V
A61-55 (VCPA) - A61-56 (EPA) B - W Power source of accelerator pedal position sensor (for VPA1) Ignition switch ON 4.5 to 5.5 V
A61-57 (VCP2) - A61-58 (EPA2) L - R Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
A61-43 (STA) - B76-109 (E1) SB - BR Starter signal Cranking 6.0 V or higher
B76-51 (INJF) - B76-109 (E1) P - BR EDU Idling Pulse generation
(See waveform 3)
B76-50 (#1) - B76-109 (E1) GR - BR Injector Idling Pulse generation
(See waveform 2)
B76-49 (#2) - B76-109 (E1) G - BR
B76-48 (#3) - B76-109 (E1) LG - BR
B76-47 (#4) - B76-109 (E1) L - BR
B76-52 (PRD) - B76-109 (E1) B - BR Pressure discharge valve drive signal Ignition switch off 4 to 5.5 V
B76-62 (IDLO) - B76-109 (E1) Y - BR EDU Idling 4 to 5.5 V
B76-103 (NE+) - B76-102 (NE-) W - B Crankshaft position sensor Idling Pulse generation
(See waveform 4)
B76-80 (G+) - B76-79 (G-) R - G Camshaft position sensor Idling Pulse generation
(See waveform 4)
A61-35 (STP) - B76-109 (E1) L - BR Stop light switch Ignition switch ON, brake pedal depressed 7.5 to 14 V
Ignition switch ON, brake pedal released 0 to 1.5 V
A61-34 (ST1-) - B76-109 (E1) GR - BR Stop light switch Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A61-26 (TC) - B76-109 (E1) G - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A61-12 (W) - B76-109 (E1) R - BR MIL MIL illuminated 0 to 3 V
MIL not illuminated 11 to 14 V
A61-14 (SPD) - B76-109 (E1) V- BR Speed signal from combination meter Ignition switch ON, drive wheels rotating slowly Pulse generation
(See waveform 6)
B76-93 (VCPM) - B76-72 (EPIM) V- BR Power source of manifold absolute pressure sensor Ignition switch ON 4.5 to 5.5 V
B76-117 (PIM) - B76-72 (EPIM) G- BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.3 to 0.9 V
Atmospheric pressure 0.8 to 1.4 V
Positive pressure of 69 kPa (518 mmHg, 20.3 in.Hg) applied 1.6 to 2.2 V
A61-13 (TACH) - B76-109 (E1) GR - BR Engine speed Idling Pulse generation
(See waveform 7)
B76-68 (VCM) - B76-67 (E2M) V - BR Fuel pressure sensor Ignition switch ON 4.5 to 5.5 V
B76-69 (VCS) - B76-91 (E2S) R - L Fuel pressure sensor Ignition switch ON 4.5 to 5.5 V
B76-66 (PCR1) - B76-67 (E2M) P - BR Fuel pressure sensor (main) Idling 1.8 to 2.1 V
B76-114 (PCR2) - B76-91 (E2S) W - L Fuel pressure sensor (sub) Idling 1.2 to 1.5 V
B76-54 (ALT) - B76-109 (E1) B - BR Generator duty ratio Idling Pulse generation
(See waveform 8)
B76-41 (PCV+) - B76-81 (PCV-) LG - R Suction control valve Idling Pulse generation
(See waveform 1)
B76-83 (VN) - B76-109 (E1) Y - BR Vacuum regulating valve assembly (for turbocharger control) Idling Pulse generation
(See waveform 5)
B76-105 (FIV) - B76-109 (E1) GR - BR Exhaust fuel addition injector Engine warmed up, idling, every 1 to 2 minutes Pulse generation
B76-97 (VCVL) - B76-96 (EVLU) W - BR Throttle position sensor Ignition switch ON 4.5 to 5.5 V
B76-119 (VLU) - B76-96 (EVLU) G - BR Throttle position sensor Ignition switch ON, throttle valve fully opened 2.8 to 3.8 V
B76-42 (M+) - B76-84 (ME01) V - W-B Throttle valve duty signal Engine warmed up, engine racing Pulse generation
B76-43 (M-) - B76-84 (ME01) P - W-B Throttle valve duty signal Engine warmed up, engine racing Pulse generation
B76-94 (VCEG) - B76-95 (EEGL) W - BR EGR valve position sensor Ignition switch ON 4.5 to 5.5 V
B76-118 (EGLS) - B76-95 (EEGL) GR - BR EGR valve position sensor Ignition switch ON 1.03 to 1.37 V
B76-86 (EGM+) - B76-84 (ME01) W - W-B EGR valve duty signal Engine warmed up, idling Pulse generation
B76-85 (EGM-) - B76-84 (ME01) B - W-B EGR valve duty signal Engine warmed up, idling Pulse generation
B76-122 (THCI) - B76-99 (ETCI) L - BR Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
B76-121 (THCO) - B76-120 (ETCO) P - BR Exhaust gas temperature sensor Engine warmed up, idling 4.6 to 4.9 V
B76-113 (THIA) - B76-90 (ETHI) Y- BR Intake air temperature sensor (turbo) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
B76-112 (THF) - B76-89 (ETHF) GR - BR Fuel temperature sensor Ignition switch ON 0.5 to 3.4 V
B76-111 (THW) - B76-88 (ETHW) B - BR Engine coolant temperature sensor Idling, engine coolant temperature at 60 to 120°C (140 to 248°F) 0.2 to 1.0 V
B76-93 (VCPM) - B76-74 (EPEX) V - BR Power source of differential pressure sensor Ignition switch ON 4.5 to 5.5 V
B76-98 (PEX) - B76-74 (EPEX) P - BR Differential pressure sensor Ignition switch ON 0.4 to 4.8 V
B76-104 (HAF2) - B76-46 (E05) L - W-B Air fuel ratio sensor heater Ignition switch ON 11 to 14 V
B76-125 (AF2+) - B76-46 (E05) L - W-B Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V
B76-126 (AF2-) - B76-46 (E05) Y - W-B Air fuel ratio sensor Ignition switch ON 2.0 to 2.5 V
B76-65 (VG) - B76-64 (EVG) R - G MAF meter power source Ignition switch ON Pulse generation
B76-110 (THA) - B76-87 (ETHA) W - BR Intake air temperature sensor Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
A61-22 (FANL) - B76-109 (E1) R - BR FAN NO. 3 relay Ignition switch ON 11 to 14 V
Idling with A/C on
or
High engine coolant temperature
Below 1.5 V
A61-21 (FANH) - B76-109 (E1) W - BR FAN NO. 1, 2 relay Idling with high engine coolant temperature Below 1.5 V
A61-7 (CANH) - B76-109 (E1) Y - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 9)
A61-6 (CANL) - B76-109 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 10)


b.
A208446
2.65,0.215 3.288,0.379 0.638,0.163 10 10 V/DIV. 0.049,1.108 0.464,1.272 0.416,0.163 10 PCV+ 1.471,1.84 2.436,2.004 0.965,0.163 10 5 msec./DIV.

Using an oscilloscope, check waveform 1.

Waveform 1:

Suction control valve signal

Item Content
Terminal No. (Symbol) B76-41 (PCV+) - B76-81 (PCV-)
Tool Setting 10 V/DIV., 5 msec./DIV.
Condition Idling or cranking with warm engine


HINT:

The waveform varies depending on the suction control valve operation.



c.
A208447
2.734,0.144 3.309,0.308 0.575,0.163 10 5 V/DIV. 0.173,0.406 0.574,0.569 0.401,0.163 10 (a) #1 0.173,0.79 0.574,0.953 0.401,0.163 10 (b) #3 0.173,1.177 0.574,1.34 0.401,0.163 10 (c) #4 0.173,1.572 0.574,1.735 0.401,0.163 10 (d) #2 1.496,1.844 2.461,2.007 0.964,0.163 10 20 msec./DIV.

Using an oscilloscope, check waveform 2.

Waveform 2:

No. 1 injector injection signal

No. 2 injector injection signal

No. 3 injector injection signal

No. 4 injector injection signal

Item Content
Terminal No. (Symbol) (a) B76-50 (#1) - B76-109 (E1)
(b) B76-48 (#3) - B76-109 (E1)
(c) B76-47 (#4) - B76-109 (E1)
(d) B76-49 (#2) - B76-109 (E1)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on the injector injection.



d.
A208448
2.689,0.248 3.264,0.412 0.575,0.163 10 2 V/DIV. 0.294,0.747 0.633,0.91 0.339,0.163 10 INJF 1.589,1.799 2.553,1.963 0.964,0.163 10 20 msec./DIV.

Using an oscilloscope, check waveform 3.

Waveform 3:

Injector injection confirmation signal

Item Content
Terminal No. (Symbol) B76-51 (INJF) - B76-109 (E1)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on the injector injection.



e.
A208449
2.707,0.147 3.282,0.31 0.575,0.163 10 5 V/DIV. 0.043,0.436 0.49,0.599 0.447,0.163 10 (a) NE 0.123,1.261 0.518,1.424 0.395,0.163 10 (b) G 1.013,1.786 2.45,1.949 1.437,0.163 10 20 msec./DIV. (Idling)

Using an oscilloscope, check waveform 4.

Waveform 4:

Crankshaft position sensor signal

Camshaft position sensor signal

Item Content
Terminal No. (Symbol) (a) B76-103 (NE+) - B76-102 (NE-)
(b) B76-80 (G+) - B76-79 (G-)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on the engine speed.



f.
A284201
0.302,0.917 0.615,1.115 0.313,0.198 10 VN 2.771,0.198 3.354,0.76 0.583,0.563 10 5 V/DIV. 2.938,1.104 3.333,1.625 0.396,0.521 10 GND 1.677,1.823 2.51,2.031 0.833,0.208 10 1 msec./DIV.

Using an oscilloscope, check waveform 5.

Waveform 5:

VRV for turbocharger control signal

Item Content
Terminal No. (Symbol) B76-83 (VN) - B76-109 (E1)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine


HINT:

The waveform changes depending on the electric vacuum regulating valve for turbocharger operation.



g.
A284202
0.177,1.104 0.635,1.302 0.458,0.198 10 SPD 2.781,0.156 3.344,0.333 0.563,0.177 10 5 V/DIV. 2.927,1.115 3.313,1.354 0.385,0.24 10 GND 1.656,1.875 2.583,2.073 0.927,0.198 10 20 msec./DIV.

Using an oscilloscope, check waveform 6.

Waveform 6:

Vehicle speed signal

Item Content
Terminal No. (Symbol) A61-14 (SPD) - B76-109 (E1)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving vehicle


HINT:

The wavelength becomes shorter as the vehicle speed increases.



h.
A284203
0.26,1 0.875,1.198 0.615,0.198 10 TACH 2.792,0.302 3.323,0.625 0.531,0.323 10 5 V/DIV. 2.958,1.021 3.302,1.333 0.344,0.313 10 GND 1.76,1.896 2.76,2.094 1,0.198 10 20 msec./DIV.

Using an oscilloscope, check waveform 7.

Waveform 7:

Engine speed signal

Item Content
Terminal No. (Symbol) A61-13 (TACH) - B76-109 (E1)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine


HINT:

The wavelength becomes shorter as the engine speed increases.



i.
A284204
0.354,1.01 0.813,1.208 0.458,0.198 10 ALT 2.771,0.333 3.313,0.615 0.542,0.281 10 5 V/DIV. 2.938,1.396 3.26,1.688 0.323,0.292 10 GND 1.75,1.896 2.583,2.083 0.833,0.188 10 5 msec./DIV.

Using an oscilloscope, check waveform 8.

Waveform 8:

Generator signal

Item Content
Terminal No. (Symbol) B76-54 (ALT) - B76-109 (E1)
Tool Setting 5 V/DIV., 5 msec./DIV.
Condition Idling



j.
A284205
0.229,0.844 0.844,1.042 0.615,0.198 10 CANH 2.76,0.177 3.313,0.51 0.552,0.333 10 1 V/DIV. 2.917,1.25 3.281,1.521 0.365,0.271 10 GND 1.729,1.75 2.583,1.948 0.854,0.198 10 10 μsec./DIV.

Using an oscilloscope, check waveform 9.

Waveform 9:

CAN communication signal

Item Content
Terminal No. (Symbol) A61-7 (CANH) - B76-109 (E1)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and ignition switch ON


HINT:

The waveform varies depending on the CAN communication signal.



k.
A284206
1.792,1.729 2.635,1.906 0.844,0.177 10 10 μsec./DIV. 0.313,0.813 0.927,1.01 0.615,0.198 10 CANL 2.802,0.167 3.365,0.333 0.563,0.167 10 1 V/DIV. 2.938,1.219 3.26,1.448 0.323,0.229 10 GND

Using an oscilloscope, check waveform 10.

Waveform 10:

CAN communication signal

Item Content
Terminal No. (Symbol) A61-6 (CANL) - B76-109 (E1)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and ignition switch ON


HINT:

The waveform varies depending on the CAN communication signal.