Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0168  Fuel Temperature Too High  


DESCRIPTION

Refer to DTC P0180 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0180).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0168 Fuel Temperature Too High All of following conditions are met (1 trip detection logic):
·

The engine speed is more than 1400 rpm.

·

The vehicle speed is more than 10 km/h (6.25 mph).

·

The fuel temperature is 110°C (230°F) or higher for 1 second or more.


Fuel lines or fuel filter clogged Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0168 Drive vehicle at high speed or with heavy load (Use freeze frame data from time malfunction occurred as reference while driving)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0168)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P0168 is output
DTC P0168 and other DTCs are output


HINT:

If any DTCs other than P0168 are output, troubleshoot those DTCs first.




DTC P0168 is output

2.CHECK SUPPLY PUMP ASSEMBLY

DTC P0168 and other DTCs are output

2.CHECK SUPPLY PUMP ASSEMBLY
a.

Perform a visual inspection of the exterior of the supply pump assembly and check that there are no fuel leaks.

OK:

There are no fuel leaks or stains.



Result:
Proceed to
OK
NG



OK

3.REPLACE FUEL FILTER ELEMENT ASSEMBLY

NG

4.REPLACE SUPPLY PUMP ASSEMBLY
3.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE SUPPLY PUMP ASSEMBLY
a.

Replace the supply pump assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.PERFORM SUPPLY PUMP INITIALIZATION
6.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Drive the vehicle in a city area and check that the value of Fuel Temperature does not exceed 110°C (230°F).


Result:
Proceed to
NEXT



NEXT

END