Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P2453 is present, refer to the DTC chart for DPF system (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



A128654E09
4.438,1.208 4.25,1.385 false 4.583,1.115 4.729,1.313 false 4.406,1.167 4.24,1.208 false 5.333,3.042 5.104,2.552 5.104,2.552 5.146,2.552 false 1.302,2.26 0.802,2.917 false 2.76,2.552 2.885,2.917 false 1.688,1.052 1.688,1.208 false 1.302,0.708 2.125,0.885 0.823,0.177 10 Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 DPF Catalytic Converter 2.344,2.938 3.635,3.271 1.292,0.333 10 Differential Pressure Sensor 3.854,0.052 5.708,0.24 1.854,0.188 10 Property of Output Voltage: 4.76,1.25 5.646,1.417 0.885,0.167 10 Stores P2455 5.156,2.479 6.063,2.646 0.906,0.167 10 Stores P2454 4.052,0.635 6.073,0.813 2.021,0.177 10 Differential Pressure Voltage (V) 4.021,0.938 4.396,1.104 0.375,0.167 10 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 4.800 3.865,1.333 4.24,1.5 0.375,0.167 10 4.650 4.021,2.344 4.396,2.51 0.375,0.167 10 1.530 4.021,2.563 4.396,2.729 0.375,0.167 10 0.750 4.021,2.719 4.396,2.885 0.375,0.167 10 0.555 4.021,2.865 4.396,3.031 0.375,0.167 10 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 0 4.771,3.229 4.875,3.385 0.104,0.156 10 0 4.531,3.229 4.708,3.396 0.177,0.167 10 -5 4.938,3.229 5.229,3.396 0.292,0.167 10 20.0 6.469,3.24 6.854,3.406 0.385,0.167 10 100.0 4.323,3.417 6.813,3.615 2.49,0.198 10 Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration. The sensor is a semiconductor-type that is not influenced by exhaust gases.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference between the pressure before and after the catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

HINT:

If the vacuum hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance When the output voltage from the differential pressure sensor output voltage is reversal of positive and negative pressure (and vice versa).
(1 trip detection logic)
·

Incorrect differential pressure sensor hose routing

·

Differential pressure sensor vacuum hose is clogged

·

Blockage in vacuum transmitting pipe sub-assembly

·

Differential pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2453 DPF Differential Pressure

HINT:
·

DTC P2454 (Diesel Particulate Filter Pressure Sensor "A" Circuit Low) and/or DTC P2455 (Diesel Particulate Filter Pressure Sensor "A" Circuit High) will be stored if there is an open or short malfunction in the differential pressure sensor circuit.

·

After confirming DTC P2453, check the differential pressure in "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" using the GTS.


Reference:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2453 Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2453)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P2453 is output
DTC P2453 and other DTCs are output


HINT:

If any DTCs other than P2453 are output, troubleshoot those DTCs first.




DTC P2453 is output

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)

DTC P2453 and other DTCs are output

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)
a.

Check if the vacuum hose routing between the differential pressure sensor and vacuum transmitting pipe is correct.

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR(for DPF)>INSTALLATION


b.

Check that there is no exhaust gas leakage between the differential pressure sensor and vacuum transmitting pipe.


Result:
Proceed to
OK
NG



OK

3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE

NG

8.CORRECT TO NORMAL CONNECTION
3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect the vacuum hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

NG

7.REPLACE CLOGGED PARTS
4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

d.

Check that the differential pressure is as specified below.

Result
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal


Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Replace the differential pressure sensor assembly.

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

g.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition DPF Differential Pressure
2500 rpm without load 1.30 kPa




h.

Start the engine.


i.

Engine is running at 4000 rpm with no load for 10 seconds or more.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

k.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P2453.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE CLOGGED PARTS
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CORRECT TO NORMAL CONNECTION
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED