Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › CYLINDER HEAD
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046813 CYLINDER HEAD A

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A150967E01
0.142,0.058 0.448,0.216 0.306,0.159 10 SST 1.342,0.635 0.5,0.164 0.5,0.164 1.231,1.197 false

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A150969C08
1.344,0.573 0.656,0.167 0.656,0.167 1.229,1.156 false 3.115,0.948 2.948,1.073 2.948,1.073 2.948,1.469 false 0.26,0.083 0.563,0.229 0.302,0.146 10 SST 2.896,1.5 3.208,1.677 0.313,0.177 10 *1
*1 Protrusion Height


Using SST and a hammer, tap in a new intake guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

9.9 to 10.3 mm (0.390 to 0.406 in.)



h.
A150971

Using a sharp 5.5 mm reamer, ream the intake guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A150968E01
1.522,1.759 1.843,1.908 0.321,0.15 10 SST 2.063,0.83 1.751,1.749 1.751,1.749 2.222,1.192 false

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A150970C08
0.875,1.021 0.708,1.177 0.708,1.177 0.708,1.448 false 1.938,0.458 1.667,1.573 1.667,1.573 2.198,1.146 true 0.625,1.448 1.063,1.635 0.438,0.188 10 *1 1.438,1.625 1.75,1.802 0.313,0.177 10 SST
*1 Protrusion Height


Using SST and a hammer, tap in a new exhaust guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

11.15 to 11.55 mm (0.439 to 0.455 in.)



h.
A150972

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE SPARK PLUG TUBE

NOTICE:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A211988C05
2.698,0.354 2.51,0.354 2.51,0.354 2.281,0.865 false 2.719,0.229 2.885,0.385 0.167,0.156 10 *1 1.625,1.708 1.802,1.865 0.177,0.156 10 *2 1.833,0.26 2,0.417 0.167,0.156 10 *3
*1 Adhesive
*2 Seal Diameter
*3 Distance


Apply adhesive onto the shaded area of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


Distance from end of tube:

1.0 to 7.0 mm (0.0394 to 0.294 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.




b.
A205906C06
2.365,3.146 2.552,3.323 0.188,0.177 10 *1
*1 Protrusion Height


Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

122 mm (4.80 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 11151A 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.
A150959C10
1.342,2.996 1.518,3.163 0.176,0.167 10 *3 1.574,3.687 1.765,3.855 0.191,0.168 10 *1 0.775,2.401 0.951,2.568 0.176,0.167 10 *2
*1 Protrusion Height
*2 Width
*3 Height


Remove the ring pins.


b.

Using a plastic-faced hammer, tap in a new ring pin to the specified protrusion height.

Standard Ring Pin:
Height Width Protrusion
11.7 to 12.3 mm (0.461 to 0.484 in.) 12.0 mm (0.472 in.) 6.5 to 7.5 mm (0.256 to 0.295 in.)