Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › CYLINDER BLOCK
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046814 CYLINDER BLOCK A

3ZR-FAE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 11434J 1.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.
A297852C02
3.063,3.271 3.375,3.427 0.313,0.156 10 false *1 0.677,2.927 0.99,3.083 0.313,0.156 10 false *2 1.385,3.552 1.698,3.708 0.313,0.156 10 false *3 0.354,0.438 0.667,0.594 0.313,0.156 10 false *a
*1 Protrusion Height
*2 Width
*3 Height
*a Upper Side


Using a plastic-faced hammer, tap in the ring pins.

Standard Ring Pin:
Height Width Protrusion
14.3 to 14.7 mm (0.563 to 0.579 in.) 12.9 to 13.0 mm (0.508 to 0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap in the straight pins.

A207265C01
4.427,3.094 3.948,3.094 3.948,3.094 4.729,3.573 true 4.365,0.854 4.021,0.854 true 2.302,1.188 2.573,1.188 false 1.323,2.063 0.927,2.063 true 1.563,1.854 0.917,1.5 0.917,1.5 0.75,1.5 true 6.688,1.906 6.344,1.906 true 3.135,3.417 2.792,3.417 true 1.479,3.198 1.135,3.198 true 0.625,0.135 0.885,0.313 0.26,0.177 10 *a 3.656,0.146 3.969,0.323 0.313,0.177 10 *b 0.667,2.375 1.021,2.573 0.354,0.198 10 *c 3.656,2.385 3.917,2.594 0.26,0.208 10 *d 0.625,1.417 0.792,1.594 0.167,0.177 10 A 0.802,1.979 0.969,2.156 0.167,0.177 10 B 1,3.115 1.167,3.292 0.167,0.177 10 C 3.177,3.344 3.344,3.521 0.167,0.177 10 C 3.813,3.01 3.979,3.188 0.167,0.177 10 E 2.594,1.115 2.76,1.292 0.167,0.177 10 B 3.896,0.781 4.063,0.958 0.167,0.177 10 D 6.719,1.833 6.885,2.01 0.167,0.177 10 D 5.229,4.656 5.406,4.844 0.177,0.188 10 *3 2.5,4.677 2.719,4.823 0.219,0.146 10 *2 2.021,5.198 2.167,5.417 0.146,0.219 10 *1
*1 Width *2 Height
*3 Protrusion Height - -
*a Front Side *b Lower Side
*c Rear Side *d LH Side


Standard Straight Pin:
Item Height Width Protrusion
Pin A 36 mm (1.42 in.) 10 mm (0.394 in.) 18.5 to 19.5 mm (0.728 to 0.768 in.)
Pin B 12 mm (0.472 in.) 4.0 mm (0.156 in.) 5.0 to 7.0 mm (0.197 to 0.276 in.)
Pin C 22 mm (0.866 in.) 10 mm (0.394 in.) 11 to 13 mm (0.433 to 0.512 in.)
Pin D 18 mm (0.708 in.) 8.0 mm (0.315 in.) 8.0 to 10.0 mm (0.315 to 0.394 in.)
Pin E 12 mm (0.472 in.) 4.0 mm (0.156 in.) 5.0 to 6.0 mm (0.197 to 0.236 in.)



Hide 13201A 3.REPLACE CONNECTING ROD SMALL END BUSH

a.
A132154E01
0.644,0.325 0.967,0.495 0.323,0.170 10 SST 1.022,0.414 1.143,0.416 1.143,0.416 1.521,0.654 false

Using SST and a press, press out the connecting rod small end bush.

SST
09222-30010  


b.
A132157C06
2.758,1.153 2.977,1.323 0.219,0.17 10 *1 2.157,0.843 2.698,1.241 2.698,1.241 2.225,1.668 false
*1 Oil Hole


Align the oil holes of a new connecting rod small end bush and the connecting rod.


c.
A132154E01
0.644,0.325 0.967,0.495 0.323,0.170 10 SST 1.022,0.414 1.143,0.416 1.143,0.416 1.521,0.654 false

Using SST and a press, press in the connecting rod small end bush.

SST
09222-30010  


d.
A132159

Using a pin hole grinder, hone the bush to obtain the standard oil clearance between the bush and piston pin.

Standard oil clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)



e.
A132160

Coat the piston pin with engine oil. Push the piston pin into the connecting rod with your thumb to check that the piston pin fits at normal room temperature.