Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046816 ENGINE UNIT G

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the lash adjuster assembly into a container full of new engine oil.


b.

Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  

A277103
1.177,1.063 1.531,0.604 true 4.417,0.5 4.833,0.5 false 5.333,0.5 5.917,0.5 false 4.354,1.25 4.917,1.25 false 5.969,1.25 5.333,1.25 false 4.25,1.667 4.917,1.667 true 6.083,1.667 5.333,1.667 true 6.167,2.083 5.333,2.083 true 4.146,2.083 4.917,2.083 true 4.969,2.5 4.302,2.198 true 6.01,2.219 5.198,2.51 true 4.333,1.063 4.948,0.885 true 6.031,0.969 5.229,0.885 true 1.625,0.521 2.083,0.719 0.458,0.198 10 SST 5,0.417 5.458,0.615 0.458,0.198 10 SST 5.021,0.802 5.333,1 0.313,0.198 10 *1 5.021,1.167 5.333,1.365 0.313,0.198 10 *2 5.021,1.583 5.333,1.781 0.313,0.198 10 *3 5.021,2 5.333,2.198 0.313,0.198 10 *4 5.031,2.417 5.344,2.615 0.313,0.198 10 *5 4.073,0.115 4.385,0.313 0.313,0.198 10 *a 6.146,0.094 6.458,0.292 0.313,0.198 10 *b
*1 Tapered Path *2 Plunger
*3 Low Pressure Chamber *4 Check Ball
*5 High Pressure Chamber - -
*a CORRECT *b INCORRECT



c.

Squeeze SST and the valve lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air bleeding is not possible.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


Hide 13506 3.INSPECT CHAIN SUB-ASSEMBLY

a.
A162995
1.625,1.208 1.885,1.375 0.26,0.167 10 *1 0.823,1.833 0.938,2 0.115,0.167 10 1 0.99,1.833 1.125,2.01 0.135,0.177 10 2 1.146,1.833 1.271,2 0.125,0.167 10 3 1.313,1.833 1.448,2.021 0.135,0.188 10 4 1.458,1.833 1.583,2.01 0.125,0.177 10 5 0.677,1.833 0.802,2.031 0.125,0.198 10 0 2.5,1.823 2.719,2 0.219,0.177 10 14 2.677,1.823 2.917,1.99 0.24,0.167 10 15
*1 Measuring Area


Pull the chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

115.2 mm (4.54 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the chain sub-assembly.


Hide 13507 4.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.

Pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf).


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

102.1 mm (4.02 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13519 5.INSPECT OIL PUMP DRIVE GEAR

a.
A053035

Place the No. 2 chain sub-assembly around the oil pump drive gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive gear and No. 2 chain sub-assembly.

Minimum gear diameter (with No. 2 chain sub-assembly):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive gear.


Hide 15163 6.INSPECT OIL PUMP DRIVE SHAFT GEAR

a.
A053036

Place the No. 2 chain sub-assembly around the oil pump drive shaft gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft gear and No. 2 chain sub-assembly.

Minimum gear diameter (with No. 2 chain sub-assembly):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive shaft gear.


Hide 13050 7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A063864

Place the chain sub-assembly around the camshaft timing gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.

Minimum gear diameter (with chain sub-assembly):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.


Hide 8.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A150911

Place the chain sub-assembly around the camshaft timing exhaust gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.

Minimum gear diameter (with chain sub-assembly):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A053035

Place the chain sub-assembly around the crankshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the crankshaft timing sprocket and chain sub-assembly.

Minimum gear diameter (with chain sub-assembly):

51.1 mm (2.01 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.


Hide 13559 10.INSPECT CHAIN TENSIONER SLIPPER

a.
A150912

Using a vernier caliper, measure the chain tensioner slipper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the chain tensioner slipper.


Hide 13561 11.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A173603

Using a vernier caliper, measure the No. 1 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13549 12.INSPECT CHAIN TENSIONER PLATE

a.
A126893

Using a vernier caliper, measure the chain tensioner plate wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the chain tensioner plate.


Hide 13540 13.INSPECT NO. 1 CHAIN TENSIONER

a.
A146263
0.854,0.469 1.104,0.635 0.25,0.167 10 *a 0.49,0.771 0.75,0.927 0.26,0.156 10 *b 1.219,1.417 1.448,1.573 0.229,0.156 10 *c
*a Raise
*b Move
*c Lock


Check that the plunger moves smoothly when the cam is raised with your finger.


b.

Release the cam, and then check that the plunger is locked in place by the cam and does not move when pushed with your finger.

If necessary, replace the No. 1 chain tensioner.


Hide 11101A 14.INSPECT CYLINDER HEAD BOLT

a.
A209191
1.667,1.052 1.927,1.24 0.26,0.188 10 *1 2.135,1.656 3.177,1.844 1.042,0.188 10 *2 1.406,2.781 2,2.969 0.594,0.188 10 *3
*1 Measurement Length
*2 Measuring Area
*3 Distance


Using a vernier caliper, measure the length of the cylinder head bolt from the seat to the end.

Standard length:

146.8 to 148.2 mm (5.78 to 5.83 in.)


Maximum length:

149.2 mm (5.87 in.)


If the length is more than the maximum, replace the cylinder head bolt.


b.

Using a vernier caliper, measure the diameter of the elongated thread at the measuring area.

Distance:

115 mm (4.53 in.)


Standard diameter:

9.77 to 9.96 mm (0.385 to 0.392 in.)


Minimum diameter:

9.4 mm (0.370 in.)


If the diameter is less than the minimum, replace the cylinder head bolt.

HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.



Hide 17141 15.INSPECT EXHAUST MANIFOLD

a.
A158847

Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head sub-assembly.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold.