Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › ENGINE COOLANT TEMPERATURE SENSOR
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0046864 ENGINE COOLANT TEMPERATURE SENSOR G

3ZR-FAE ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  INSPECTION  


PROCEDURE

Hide 89422 1.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

a.

Measure the resistance according to the value(s) in the table below.

A196021
5.948,1.104 6.188,0.698 6.188,0.698 6.313,0.698 false 4.823,0.021 5.042,0.26 0.219,0.24 10 *1 6.375,0.604 6.583,0.823 0.208,0.219 10 *3 5.063,0.125 5.385,0.333 0.323,0.208 8 30 5.063,0.26 5.385,0.469 0.323,0.208 8 20 5.063,0.479 5.385,0.688 0.323,0.208 8 10 5.063,0.719 5.385,0.927 0.323,0.208 8 5 5.063,0.885 5.385,1.094 0.323,0.208 8 3 5.063,1.021 5.385,1.229 0.323,0.208 8 2 5.063,1.24 5.385,1.448 0.323,0.208 8 1 5.042,1.781 5.365,1.99 0.323,0.208 8 0.2 5.042,1.646 5.365,1.854 0.323,0.208 8 0.3 5.042,1.479 5.365,1.688 0.323,0.208 8 0.5 5.042,2.01 5.365,2.219 0.323,0.208 8 0.1 5.563,2.292 5.76,2.458 0.198,0.167 8 0 5.76,2.292 5.99,2.458 0.229,0.167 8 20 6.01,2.292 6.292,2.615 0.281,0.323 8 40 6.26,2.292 6.5,2.479 0.24,0.188 8 60 6.51,2.292 6.938,2.615 0.427,0.323 8 80 6.792,2.292 7.146,2.615 0.354,0.323 8 100 5.24,2.292 5.448,2.479 0.208,0.188 8 -20 4.948,2.323 5.219,2.521 0.271,0.198 10 *2 1.177,0.833 1.406,1.094 0.229,0.26 10 *a 4.813,0.292 5.042,0.479 0.229,0.188 10 kΩ 5.875,2.583 6.344,2.771 0.469,0.188 10 °C (°F) 5.25,2.438 5.531,2.615 0.281,0.177 8 (-4) 5.5,2.427 5.781,2.604 0.281,0.177 8 (32) 5.719,2.438 6,2.615 0.281,0.177 8 (68) 5.948,2.427 6.365,2.604 0.417,0.177 8 (104) 6.219,2.427 6.604,2.625 0.385,0.198 8 (140) 6.49,2.427 6.854,2.615 0.365,0.188 8 (176) 6.781,2.427 7.135,2.625 0.354,0.198 8 (212)
*1 Resistance *2 Temperature
*3 Acceptable Range - -
*a Component without harness connected
(Engine Coolant Temperature Sensor)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.310 to 0.326 kΩ


NOTICE:

When checking the engine coolant temperature sensor in water, do not allow water to contact the terminals. After completing the check, dry the engine coolant temperature sensor.


If the result is not as specified, replace the engine coolant temperature sensor.