Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › EXHAUST PIPE
RM3090E _51 Engine / Hybrid System _008399 2AR-FE INTAKE / EXHAUST _0046898 EXHAUST PIPE A

2AR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 17401 2.INSTALL FRONT EXHAUST PIPE SUB-ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.63 in.)


If the length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194C06
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




d.

Install the front exhaust pipe sub-assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17402 3.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY

a.

Install a new gasket to the front exhaust pipe sub-assembly.


b.

Install the front No. 2 exhaust pipe sub-assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Connect the heated oxygen sensor connector.


Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front No. 2 exhaust pipe sub-assembly.


b.

Connect the 3 exhaust pipe supports to install the center exhaust pipe assembly.


c.

Install the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 5.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.63 in.)


If the length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.




d.

Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly.


e.

Install the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 6.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

HINT:

If an exhaust gas leak has been repaired, perform an inspection following the repair.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION