Home › Engine / Hybrid System › 2AR-FE LUBRICATION › OIL AND OIL FILTER
RM3090E _51 Engine / Hybrid System _008401 2AR-FE LUBRICATION _0046909 OIL AND OIL FILTER A

2AR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner thoroughly to remove any used engine oil. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Clean and install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 2.REMOVE OIL FILTER CAP ASSEMBLY

a.
A132053
1.563,0.271 1.406,0.271 1.406,0.271 1.115,0.604 false 2.927,1.063 2.781,1.063 2.781,1.063 2.51,1.406 false 1.594,0.177 1.76,0.354 0.167,0.177 10 *1 2.979,0.969 3.146,1.146 0.167,0.177 10 *2
*1 Pipe
*2 Hose


Connect a hose with an inner diameter of 15 mm (0.591 in.) to the pipe.


b.
A196672

Remove the oil filter drain plug.


c.
A301120
2.667,1.625 2.771,1.625 2.771,1.625 2.885,2.25 true 2.833,2.958 2.948,2.958 2.948,2.958 3.031,2.656 false 2.167,2.281 2.458,2.281 false 2.375,2.823 2.531,2.823 2.531,2.823 2.865,2.573 true 1.979,2.188 2.167,2.365 0.188,0.177 10 false *1 2.479,1.542 2.667,1.719 0.188,0.177 10 false *2 2.646,2.875 2.833,3.052 0.188,0.177 10 false *3 2.188,2.729 2.375,2.906 0.188,0.177 10 false *4
*1 Oil Filter Cap
*2 Valve
*3 Pipe
*4 O-Ring


Install the pipe to the oil filter cap.

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A196674

Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.


e.
A215914
0.594,0.708 0.813,0.708 0.813,0.708 1.5,1.24 false 2.813,1.146 2.677,1.146 2.677,1.146 2.448,1.385 false 2.885,1.063 3.281,1.281 0.396,0.219 10 SST 0.365,0.646 0.615,0.885 0.25,0.24 10 *1
*1 Oil Filter Bracket Clip


Using SST, remove the oil filter cap.

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip.



f.
A301119
2.417,1.146 2.813,1.146 false 0.708,0.49 1.125,0.49 false 2.865,1.063 3.042,1.229 0.177,0.167 10 false *2 0.51,0.406 0.688,0.573 0.177,0.167 10 false *1
*1 Oil Filter Element
*2 O-Ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



Hide 15620 3.INSTALL OIL FILTER CAP ASSEMBLY

a.

Clean the inside of the oil filter cap, the threads and O-ring groove.


b.
A268595
1.51,1.042 1.583,0.823 1.583,0.823 1.667,0.823 false 3.094,1.156 3.146,0.927 3.146,0.927 3.229,0.927 false 1.677,0.729 1.844,0.875 0.167,0.146 10 *1 3.24,0.833 3.406,0.979 0.167,0.146 10 *1 0.875,1.802 1.042,1.958 0.167,0.156 10 *a 2.438,1.802 2.604,1.958 0.167,0.156 10 *b
*1 O-Ring
*a CORRECT
*b INCORRECT


Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element into the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.
A296327
1.677,2.583 1.677,2.24 1.677,2.24 1.396,1.635 false 2.292,2.375 2.469,2.375 true 2.281,2.729 2.396,2.729 false 2.479,1.719 2.708,1.719 false 2.104,2.281 2.281,2.448 0.177,0.167 10 *2 2.75,1.625 2.927,1.792 0.177,0.167 10 *3 2.104,2.635 2.281,2.802 0.177,0.167 10 *1 2.677,2.823 2.854,2.99 0.177,0.167 10 *a 1.552,2.625 1.875,2.792 0.323,0.167 10 SST
*1 Oil Filter Cap
*2 O-Ring
*3 Stiffening Crankcase
*a No Gap


Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



g.

Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.
A301121
2.448,1.49 2.563,1.49 2.563,1.49 2.875,1.594 true 2.25,1.406 2.427,1.573 0.177,0.167 10 false *1
*1 O-Ring


Install the oil filter drain plug.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between any surrounding parts.



Hide 4.ADD ENGINE OIL

a.

Add new engine oil and install the oil filler cap.

Standard Oil Grade:
Oil Grade Oil Viscosity
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil 0W-20
5W-20
5W-30
10W-30
API grade SL, SM or SN multigrade engine oil 15W-40
20W-50


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter change 4.0 liters (4.2 US qts, 3.5 Imp. qts)
Drain and refill with oil filter change 4.4 liters (4.6 US qts, 3.9 Imp. qts)
Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)



Hide 5.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.