Home › Engine / Hybrid System › 2AR-FE STARTING › STARTER(for 1.6 kW Type)
RM3090E _51 Engine / Hybrid System _008402 2AR-FE STARTING _0046913 STARTER(for 1.6 kW Type) G

2AR-FE STARTING  STARTER(for 1.6 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may be hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Perform the pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A197192
2.333,1.26 2.521,2.135 2.521,2.135 2.74,2.135 true 2.156,1.26 1.542,1.938 1.542,1.938 1.396,1.938 true 2.781,2.052 3.031,2.24 0.25,0.188 10 *2 1.26,1.854 1.542,2.042 0.281,0.188 10 *1
*1 Terminal 50
*2 Terminal C


Connect the battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



b.
A197193
2.365,1.229 2.604,0.865 2.604,0.865 2.76,0.865 false 2.781,0.781 3.052,0.948 0.271,0.167 10 *1
*1 Terminal C
V100135

Disconnect


Perform the holding test.

i.

Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.
A302256
1.5,2.792 1.656,2.99 0.156,0.198 10 false -
V100135

Disconnect
V100136

Returns Inward


Check the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.

If the clutch pinion gear does not return, replace the magnet starter switch assembly.



d.

Perform the no-load performance test.

i.

Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Clamp the starter assembly in a vise.


iii.
A197195
2.385,1.583 2.167,0.948 2.167,0.948 2.01,0.948 true 2.125,1.896 1.51,2.677 1.51,2.677 1.344,2.677 true 1.823,0.844 2.094,1.01 0.271,0.167 10 *1 1.167,2.583 1.448,2.75 0.281,0.167 10 *2
*1 Terminal 30
*2 Terminal 50


Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER CLUTCH

a.
A197200
1.615,1.719 1.615,1.635 false
V100135

Free
V100136

Lock


Check the starter clutch.

i.

Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If necessary, replace the starter repair service starter kit.



Hide 28150 3.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A197181

Inspect the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnet starter switch assembly.



b.
A197182
2.539,1.279 2.739,1.448 0.2,0.169 10 *2 2.171,1.369 2.52,1.369 false 0.989,1.604 1.172,1.773 0.183,0.169 10 *1 1.842,1.387 1.316,1.687 1.316,1.687 1.2,1.687 false
*1 Terminal 50
*2 Terminal C


Inspect the pull-in coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A197183
1.948,1.5 1.417,1.781 1.417,1.781 1.219,1.781 true 1.323,0.344 1.51,0.167 1.51,0.167 1.698,0.167 false 1.75,0.063 2.083,0.26 0.333,0.198 10 *2 1.031,1.677 1.313,1.865 0.281,0.188 10 *1
*1 Terminal 50
*2 Switch Body


Inspect the holding coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 28160 4.INSPECT STARTER ARMATURE ASSEMBLY

a.

Inspect the commutator for an open circuit.

i.
A296175
0.823,1.469 1.042,1.469 1.042,1.469 1.313,1.281 true 1.427,1.177 1.719,0.5 1.719,0.5 1.969,0.5 true 2.021,0.396 2.333,0.552 0.313,0.156 10 *1 0.656,1.365 0.969,1.521 0.313,0.156 10 *1
*1 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.

Inspect the commutator for a short circuit.

i.
A296176
0.656,1.438 0.927,1.438 0.927,1.438 1.333,1.229 false 1.896,1.063 2.323,0.354 2.323,0.354 2.573,0.354 true 0.448,1.323 0.76,1.479 0.313,0.156 10 *1 2.625,0.25 2.938,0.406 0.313,0.156 10 *2
*1 Segment
*2 Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the surface of the commutator for dirt and burns.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


d.
A194765
2.75,0.896 3.063,1.052 0.313,0.156 10 *1
*1 Length


Using a vernier caliper, measure the commutator length.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.8 mm (0.150 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 28130 5.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A194766
0.26,0.896 0.573,1.052 0.313,0.156 10 *1
*1 Length


Using a vernier caliper, measure the brush length.

Standard length:

9.0 mm (0.354 in.)


Minimum length:

4.0 mm (0.157 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.


b.
A197190

Inspect the insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, repair or replace the starter commutator end frame assembly.