Home › Engine / Hybrid System › 2AR-FE STARTING › STARTER(for 1.6 kW Type)
RM3090E _51 Engine / Hybrid System _008402 2AR-FE STARTING _0046913 STARTER(for 1.6 kW Type) A

2AR-FE STARTING  STARTER(for 1.6 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28255 1.INSTALL PLANETARY GEAR

a.
A242576
1.344,1.229 1.354,1.198 false
V100135

High-temperature grease


Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears.


Hide 28117A 2.INSTALL RUBBER SEAL

a.

Install the rubber seal to the repair service starter kit.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A298696
0.948,0.927 0.969,0.906 false
V100135

High-temperature grease


Apply high-temperature grease to the starter armature shaft.


b.
A298692
1.396,0.51 1.302,0.51 false
V100135

High-temperature grease


Apply high-temperature grease to the washer and bearing as shown in the illustration.


c.

Install the starter armature assembly to the starter commutator end frame assembly.


d.

Install the washer.


e.

Using snap ring pliers, securely install a new snap ring to the armature shaft groove.

NOTICE:

Be sure to install the snap ring properly because it easily expands.



f.
A194767
0.563,1 0.875,1.156 0.313,0.156 10 *1
*1 Length


Using a vernier caliper, measure the length of the snap ring.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring with a new one.


Hide 28132A 4.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A197189

Install the starter commutator end frame cover to the starter commutator end frame assembly.


Hide 28177 5.INSTALL STARTER ARMATURE PLATE

a.
A194768
1.469,1.677 1.073,1.625 1.073,1.625 0.865,1.625 false 2.885,1.042 2.885,1.49 true 0.688,1.51 0.865,1.698 0.177,0.188 10 *1 2.802,1.552 2.979,1.74 0.177,0.188 10 *2
*1 Keyway
*2 Key


Insert the armature plate into the starter yoke assembly.


b.

Align the keyway of the starter armature plate with the key inside the starter yoke assembly, and install the starter armature plate.


Hide 28130 6.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A197184
1.446,0.205 1.668,0.372 0.221,0.167 10 *2 2.135,0.586 2.347,0.753 0.212,0.167 10 *1 2.507,0.95 2.413,0.68 2.413,0.68 2.361,0.68 false 1.219,0.565 1.346,0.299 1.346,0.299 1.419,0.299 false
*1 Rubber
*2 Cutout


Align the rubber of the starter commutator end frame assembly with the cutout of the starter yoke assembly.


b.

Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A298693
1.771,1.063 2.031,0.75 2.031,0.75 2.208,0.75 false 0.635,1.594 0.865,1.594 0.865,1.594 1.615,1.094 true 2.26,0.688 2.573,0.844 0.313,0.156 10 *1 0.458,1.51 0.771,1.667 0.313,0.156 10 *2
*1 Protrusion
*2 Cutout


Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.


b.

Install the starter yoke assembly with the 2 through-bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A298694
2.313,0.667 2.313,0.604 false
V100135

High-temperature grease


Apply high-temperature grease to the plunger and the lever.


b.
A197186

Pull the pinion gear and push down the lever.


c.
A197187
0.833,0.781 1.302,0.469 1.302,0.469 1.49,0.469 true 1.01,1 1.458,1.156 1.458,1.156 1.573,1.156 false 1.552,0.406 1.74,0.604 0.188,0.198 10 *1 1.594,1.063 1.771,1.26 0.177,0.198 10 *2
*1 Plunger
*2 Lever


Temporarily install the magnet starter switch assembly by hooking the plunger onto the upper side of the pinion drive lever.


d.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the lead wire to the terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)