Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR(for 100 A Type) › 2012.12–2013.11
RM3090E _57 Power Source / Network _008403 2AR-FE BATTERY / CHARGING _0046918 GENERATOR A

2AR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A298989

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.
A298990
1.708,1.01 2.063,1.729 2.063,1.729 2.24,1.729 false 0.688,1.885 0.875,1.885 0.875,1.885 0.958,1.458 false 2.313,1.646 2.979,1.844 0.667,0.198 10 SST (A) 0.156,1.813 0.823,2.01 0.667,0.198 10 SST (B)

Mount the generator assembly in a vise between aluminum plates.


b.

Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


c.
A298991
1.844,0.531 2.094,0.25 2.094,0.25 2.292,0.25 false 2.115,0.792 2.313,0.948 2.313,0.948 2.542,0.948 false 2.365,0.167 3.042,0.354 0.677,0.188 10 SST (B) 2.604,0.854 3.281,1.042 0.677,0.188 10 SST (A) 1.833,1.813 2.146,1.969 0.313,0.156 10 *a
*a Hold
V100135

Turn


Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator pulley with clutch.


d.

Remove the generator pulley with clutch.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A302251

Place the generator on the generator pulley with clutch.


b.
A298992

Remove the 3 bolts and generator rear end cover.


c.
A192780

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A192783E01
0.533,0.31 0.837,0.484 0.303,0.173 10 SST 1.583,0.78 1.028,0.404 1.028,0.404 0.902,0.404 false

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A282149

Remove the washer.


b.
A153384

Remove the generator rotor assembly from the generator drive end frame assembly.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A192785

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If the result is not as specified, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and bearing retainer.


b.
A298993
2.271,1.927 1.698,1.156 false 2.552,1.927 2.271,1.927 2.271,1.927 1.708,1.354 false 2.615,1.865 3.073,2.063 0.458,0.198 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)