Home › Engine / Hybrid System › 2AD-FHV ENGINE MECHANICAL › CYLINDER HEAD
RM3090E _51 Engine / Hybrid System _008404 2AD-FHV ENGINE MECHANICAL _0046939 CYLINDER HEAD A

2AD-FHV ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CYLINDER HEAD STUD BOLT

HINT:

If a cylinder head stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, install the cylinder head stud bolts.

Torque:
for stud bolt A and B : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for stud bolt C : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Using an E6 "TORX" socket wrench, install the cylinder head stud bolt.

Torque:
for stud bolt D : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

A298138
0.729,0.208 1.042,0.365 0.313,0.156 10 false *a 0.76,2.729 1.073,2.885 0.313,0.156 10 false *b 3.979,2.74 4.292,2.896 0.313,0.156 10 false *c 1.125,6 1.438,6.156 0.313,0.156 10 false *d 1.469,6.219 1.781,6.375 0.313,0.156 10 false *f 1.135,6.604 1.448,6.76 0.313,0.156 10 false *e 2.771,6.135 3.021,6.354 0.25,0.219 10 false *g 3.083,6.417 3.396,6.573 0.313,0.156 10 false *i 2.781,6.708 3,6.958 0.219,0.25 10 false *h 4.396,5.771 4.708,5.979 0.313,0.208 10 false *j 4.74,6.25 5.052,6.406 0.313,0.156 10 false *k 4.417,6.646 4.729,6.802 0.313,0.156 10 false *e 5.948,6.177 6.26,6.333 0.313,0.156 10 false *l 6.26,6.448 6.573,6.635 0.313,0.188 10 false *m 5.958,6.677 6.271,6.833 0.313,0.156 10 false *l 2.458,3.833 2.615,4.031 0.156,0.198 10 false B 1.354,3.823 1.51,4.021 0.156,0.198 10 false B 6.156,3.125 6.313,3.323 0.156,0.198 10 false A 4.552,3.188 4.708,3.385 0.156,0.198 10 false A 5.063,3.146 5.219,3.344 0.156,0.198 10 false A 5.615,3.135 5.771,3.333 0.156,0.198 10 false A 4.354,4.229 4.51,4.427 0.156,0.198 10 false A 4.896,4.219 5.052,4.417 0.156,0.198 10 false A 5.458,4.229 5.615,4.427 0.156,0.198 10 false A 5.99,4.24 6.146,4.438 0.156,0.198 10 false A 3.125,0.406 3.281,0.604 0.156,0.198 10 false C 0.938,2.438 1.094,2.635 0.156,0.198 10 false D 0.74,7.083 1.052,7.24 0.313,0.156 10 false A 2.427,7.094 2.74,7.25 0.313,0.156 10 false B 4.042,7.094 4.354,7.25 0.313,0.156 10 false C 5.573,7.094 5.885,7.25 0.313,0.156 10 false D
*a Cylinder Head Cover Side *b Intake Manifold Side
*c Exhaust Manifold Side *d 40 mm (1.57 in.)
*e 15 mm (0.591 in.) *f 58.5 mm (2.30 in.)
*g 20 mm (0.787 in.) *h 13 mm (0.512 in.)
*i 35 mm (1.38 in.) *j 14 mm (0.551 in.)
*k 47 mm (1.85 in.) *l 12 mm (0.472 in.)
*m 37 mm (1.45 in.) - -



Hide 11117E 2.INSTALL NO. 1 STRAIGHT SCREW PLUG WITH HEAD

a.

Apply adhesive to the No. 1 straight screw plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Using a 6 mm hexagon wrench, install the 4 No. 1 straight screw plugs.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 16268 3.INSTALL NO. 1 WATER BY-PASS PIPE

HINT:

When using a new cylinder head sub-assembly, a No. 1 water by-pass pipe must be installed.


A203751
2.177,2.344 2.49,2.5 0.313,0.156 10 *a
*a 45 to 55°


a.

Apply adhesive to a new No. 1 water by-pass pipe so that it covers the entire circumference of the part which contacts the hole of the cylinder head sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the No. 1 water by-pass pipe as shown in the illustration.


Hide 4.INSTALL WATER OUTLET

HINT:

When using a new cylinder head sub-assembly, a water outlet must be installed.


A203748
2.313,1.594 2.625,1.75 0.313,0.156 10 *a 1.26,4.104 1.573,4.26 0.313,0.156 10 *b
*a 79 to 85 mm
*b 51 to 61°


a.

Apply adhesive to a new water outlet so that it covers the entire circumference of the part which contacts the hole of the cylinder head sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the water outlet.

Standard protrusion:

79 to 85 mm (3.11 to 3.35 in.)


Standard angle:

51 to 61°



Hide 5.INSTALL ELBOW

HINT:

When using a new cylinder head sub-assembly, an elbow must be installed.


A203747
1.521,1.49 1.833,1.646 0.313,0.156 10 *a 1.427,4.198 1.74,4.354 0.313,0.156 10 *b
*a 56.5 to 62.5 mm
*b 20 to 30°


a.

Apply adhesive to a new elbow so that it covers the entire circumference of the part which contacts the hole of the cylinder head sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the elbow.

Standard protrusion:

56.5 to 62.5 mm (2.22 to 2.46 in.)


Standard angle:

20 to 30°



Hide 13734 6.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head sub-assembly.


Hide 7.INSTALL VALVE STEM OIL SEAL

a.

Apply a light coat of engine oil to a new valve stem oil seal.


b.
A111374
1.063,0.188 1.219,0.188 1.219,0.188 2.677,0.469 true 0.5,0.615 0.604,0.615 0.604,0.615 0.865,1.333 true 2.302,1.938 2.406,1.938 2.406,1.938 3.042,1.271 true 2,1.854 2.323,2.031 0.323,0.177 10 SST 0.875,0.115 1.188,0.271 0.313,0.156 10 *1 0.188,0.531 0.51,0.708 0.323,0.177 10 SST
*1 Valve Stem Oil Seal


Using SST, push in the valve stem oil seal.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the valve stem oil seal to be damaged or improperly seated.



Hide 13711 8.INSTALL INTAKE VALVE

a.
A101416
2.688,1.5 3,1.656 0.313,0.156 10 *a
*a 50 mm (1.97 in.)


Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.

Place the cylinder head sub-assembly on a wooden block.


c.

Install the intake valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



d.
A111290
1.781,0.354 1.948,0.354 1.948,0.354 2.219,0.646 false 1.427,0.281 1.719,0.448 0.292,0.167 10 SST

Using SST, compress the inner compression spring and place the valve spring retainer lock around the intake valve stem.

SST
09202-70020  


e.

Using a 5 mm pin punch and plastic-faced hammer, lightly tap the intake valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the intake valve stem tip.



Hide 13715 9.INSTALL EXHAUST VALVE

a.
A101419
2.708,1.458 3.021,1.615 0.313,0.156 10 *a
*a 50 mm (1.97 in.)


Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Place the cylinder head sub-assembly on a wooden block.


c.

Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



d.
A111289
1.063,0.427 1.354,0.188 1.354,0.188 1.5,0.188 false 1.563,0.115 1.896,0.271 0.333,0.156 10 SST

Using SST, compress the inner compression spring and place the valve spring retainer lock around the exhaust valve stem.

SST
09202-70020  


e.

Using a 5 mm pin punch and plastic-faced hammer, lightly tap the exhaust valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the exhaust valve stem tip.