Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CAMSHAFT › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046944 CAMSHAFT A

3ZR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs after replacing the camshaft No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 13750 1.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 2.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11811 3.INSTALL NO. 1 CAMSHAFT BEARING

a.

Clean the surfaces of bearings.


b.

Install the 2 No. 1 camshaft bearings.


c.
A153839C03
0.344,1.885 0.188,1.885 0.188,1.885 0.083,2.979 false 0.167,2.615 0.344,2.813 0.177,0.198 10 A 2,2.615 2.198,2.844 0.198,0.229 10 B 0.375,1.802 0.688,1.958 0.313,0.156 10 *1
*1 Vernier Caliper


Using a vernier caliper, measure the distance between the camshaft bearing cap edge and camshaft bearing edge.

Dimension (A - B) or (B - A):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Position the bearings in the center of the camshaft bearing cap by measuring dimensions A and B.



Hide 11821 4.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean both surfaces of the bearings.


b.

Install the 2 No. 2 camshaft bearings.


c.
A238701C01
0.573,4.115 0.656,4.354 0.656,4.354 0.74,4.354 false 0.74,3.521 0.969,3.719 0.229,0.198 10 A 0.771,4.271 1.083,4.427 0.313,0.156 10 *1
*1 Vernier Caliper


Using a vernier caliper, measure the distance between the bearing cap edge and camshaft bearing edge.

Dimension (A):

1.05 to 1.75 mm (0.0413 to 0.0689 in.)


NOTICE:

Position the bearings in the center of the camshaft bearing cap by measuring dimension A.



Hide 13512 5.INSTALL NO. 2 CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.

Install the No. 2 camshaft to the camshaft housing sub-assembly.


Hide 13511 6.INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.

Install the camshaft to the camshaft housing sub-assembly.


Hide 7.INSTALL CAMSHAFT BEARING CAP

a.
A293586C01
1.854,2.01 2.01,2.01 2.01,2.01 2.344,2.146 true 1.271,2.135 1.479,2.563 1.479,2.563 1.635,2.563 true 1.302,2.542 1.51,2.969 1.51,2.969 1.667,2.969 true 2.333,2.521 2.448,2.771 2.448,2.771 2.604,2.771 true 2.667,2.698 2.979,2.854 0.313,0.156 10 *1 1.698,2.885 2.01,3.042 0.313,0.156 10 *2 1.667,1.938 1.979,2.094 0.313,0.156 10 *3 2.677,2.01 3.021,2.198 0.344,0.188 10 50° 1.677,2.49 1.99,2.646 0.313,0.156 10 *3
*1 Camshaft
*2 No. 2 Camshaft
*3 Straight Pin


Apply a light coat of engine oil to the camshaft bearing caps.


b.

Check the marks and numbers on the camshaft bearing caps and place the camshaft bearing caps in the proper position and direction.

HINT:

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.



c.
A153453E01
0.763,0.321 0.960,0.484 0.197,0.162 10 10 0.742,1.579 0.883,1.741 0.141,0.162 10 9 1.375,1.579 1.516,1.741 0.141,0.162 10 5 1.404,0.335 1.545,0.497 0.141,0.162 10 6 1.944,1.579 2.086,1.741 0.141,0.162 10 1 1.944,0.335 2.086,0.497 0.141,0.162 10 2 2.449,1.579 2.590,1.741 0.141,0.162 10 3 2.449,0.335 2.590,0.497 0.141,0.162 10 4 2.953,1.579 3.095,1.741 0.141,0.162 10 7 2.953,0.335 3.095,0.497 0.141,0.162 10 8

Install the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 11103 8.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A131901C14
2.167,0.781 2.458,0.542 2.458,0.542 2.594,0.531 false 1.771,0.49 1.604,0.25 1.604,0.25 1.479,0.25 false 1.167,1.073 0.906,0.938 0.906,0.938 0.792,0.938 false 2.073,1.125 2.479,1.417 2.479,1.417 2.604,1.417 false 0.583,0.854 0.896,1.01 0.313,0.156 10 *1 1.271,0.177 1.583,0.333 0.313,0.156 10 *2 2.646,1.344 2.958,1.5 0.313,0.156 10 *3 2.646,0.458 2.958,0.615 0.313,0.156 10 *4
*1 Lash Adjuster
*2 Valve Rocker Arm
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the valve rocker arm is installed as shown in the illustration.


b.
A206178C01
1.979,2.323 2.094,2.833 2.094,2.833 2.271,2.833 true 0.104,2.656 0.26,2.833 0.156,0.177 10 A 0.104,0.396 0.26,0.573 0.156,0.177 10 B 2.302,2.771 2.615,2.927 0.313,0.156 10 *1
*1 Continuous Line


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:
Area Specified Condition
Continuous Line 3.5 to 4.5 mm (0.138 to 0.177 in.)
A 8.0 mm (0.315 in.)
B 7.0 mm (0.276 in.)


Application Length A and B:

15 mm (0.591 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A206179N01
1.469,3.156 1.667,3.365 0.198,0.208 10 9 1.948,1.906 2.125,2.125 0.177,0.219 10 1 1.958,1.417 2.135,1.615 0.177,0.198 10 2 1.896,3.135 2.083,3.354 0.188,0.219 10 3 2.406,1.896 2.615,2.104 0.208,0.208 10 4 2.448,1.427 2.656,1.625 0.208,0.198 10 5 2.354,3.146 2.542,3.365 0.188,0.219 10 6 1.49,1.906 1.656,2.094 0.167,0.188 10 7 1.49,1.406 1.656,1.604 0.167,0.198 10 8 2.896,2.615 3.177,2.833 0.281,0.219 10 10 3.094,1.99 3.375,2.219 0.281,0.229 10 16 0.146,2.906 0.406,3.135 0.26,0.229 10 15 0.146,1.604 0.396,1.844 0.25,0.24 10 14 1.135,1.333 1.406,1.552 0.271,0.219 10 17 0.104,2.271 0.365,2.469 0.26,0.198 10 13 2.781,3.135 3.031,3.365 0.25,0.229 10 12 2.854,1.438 3.125,1.646 0.271,0.208 10 11

Set the camshaft and No. 2 camshaft as shown in the illustration.


d.

Install the camshaft housing sub-assembly with the 17 bolts and tighten them in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head.




Hide 13050 9.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A146265C12
2.219,0.552 2.094,0.552 2.094,0.552 1.969,1.083 false 1.625,0.344 1.51,0.344 1.51,0.344 1.323,1.021 false 2.26,0.479 2.573,0.635 0.313,0.156 10 *1 1.667,0.26 1.979,0.417 0.313,0.156 10 *2
*1 Straight Pin
*2 Key Groove


Put the camshaft timing gear assembly and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

NOTICE:

Do not forcefully push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.



b.
A251816C01
1.49,0.115 1.344,0.115 1.344,0.115 0.823,0.583 false 1.615,1.76 1.448,1.76 1.448,1.76 0.813,1.385 false 2.583,0.719 2.833,0.938 0.25,0.219 10 A 1.531,0.042 1.844,0.198 0.313,0.156 10 *1 1.656,1.688 1.969,1.844 0.313,0.156 10 *2 0.635,1.844 0.948,2 0.313,0.156 10 *a
*1 Straight Pin
*2 Key Groove
*a View A


Turn the camshaft timing gear assembly as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

NOTICE:

Do not turn the camshaft timing gear assembly in the retard direction (clockwise).



c.
A146267C16
1.927,0.74 1.823,0.74 1.823,0.74 1.427,1.031 false 1.49,0.156 1.292,0.156 1.292,0.156 1.031,0.906 false 1.521,0.073 1.833,0.229 0.313,0.156 10 *1 1.958,0.656 2.271,0.813 0.313,0.156 10 *2 1.302,0.49 1.615,0.646 0.313,0.156 10 *a 1.24,1.875 1.552,2.031 0.313,0.156 10 *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Clearance
*b No Clearance


Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.


d.
A153890

Tighten the flange bolt while holding the hexagonal portion of the camshaft.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.
A153896C02
1.969,1.146 1.927,1.073 false
V100135

Locks when turned all the way in this direction


Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and is locked in the most retarded position.


Hide 13070A 10.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform " Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A215318C07
1.458,1.021 1.01,0.156 1.01,0.156 0.792,0.156 true 1.156,1.031 0.573,1.656 0.573,1.656 0.406,1.656 true 0.552,0.083 0.865,0.24 0.313,0.156 10 *1 0.198,1.573 0.51,1.729 0.313,0.156 10 *2
*1 Straight Pin
*2 Pin Hole


Put the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the pin hole and straight pin.

NOTICE:

Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.



b.

Lightly press the camshaft timing exhaust gear assembly against the No. 2 camshaft and turn the camshaft timing exhaust gear assembly. Push further at the position where the straight pin enters the pin hole.


c.
A146267C17
1.927,0.74 1.823,0.74 1.823,0.74 1.438,1.031 false 1.49,0.156 1.292,0.156 1.292,0.156 1.031,0.885 false 1.521,0.083 1.833,0.24 0.313,0.156 10 *1 1.969,0.667 2.281,0.823 0.313,0.156 10 *2 1.292,0.479 1.604,0.635 0.313,0.156 10 *a 1.25,1.854 1.563,2.01 0.313,0.156 10 *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Clearance
*b No Clearance


Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.


d.
A153891

Tighten the flange bolt while holding the hexagonal portion of the No. 2 camshaft.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.

Check the camshaft timing exhaust gear assembly lock.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.



Hide 13506 11.INSTALL CHAIN SUB-ASSEMBLY