Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER HEAD › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046951 CYLINDER HEAD A

3ZR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, install the stud bolts.

A297849C01
0.927,0.667 1.083,0.865 0.156,0.198 10 A 2.333,0.667 2.49,0.865 0.156,0.198 10 A 1.229,2.156 1.385,2.354 0.156,0.198 10 A 4.792,0.719 4.948,0.917 0.156,0.198 10 B 6.094,0.75 6.25,0.948 0.156,0.198 10 B 4.333,1.75 4.49,1.948 0.156,0.198 10 B 5.427,1.771 5.583,1.969 0.156,0.198 10 B 6.583,1.75 6.74,1.948 0.156,0.198 10 B 4.656,2.25 4.813,2.448 0.156,0.198 10 B 0.438,0.333 0.75,0.49 0.313,0.156 10 *a 4.021,0.333 4.333,0.49 0.313,0.156 10 *b 1.677,2.635 1.99,2.792 0.313,0.156 10 *c 1.677,3.094 1.99,3.25 0.313,0.156 10 *d 2.438,2.844 2.75,3 0.313,0.156 10 *e 5.083,2.76 5.396,2.917 0.313,0.156 10 *f 5.854,2.927 6.156,3.198 0.302,0.271 10 *g 5.083,3.115 5.396,3.271 0.313,0.156 10 *d
*a Intake Side *b Exhaust Side
*c 24 mm (0.945 in.) *d 13 mm (0.512 in.)
*e 45 mm (1.77 in.) *f 20 mm (0.787 in.)
*g 35 mm (1.38 in.) - -


Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 11117B 2.INSTALL NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If water leaks from the No. 2 straight screw plug or the plug is corroded, replace it.


a.

Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 No. 2 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 3.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 4.INSTALL VALVE STEM OIL SEAL

a.
A146313C16
3.125,0.792 3.01,0.792 3.01,0.792 2.896,1.031 false 1.146,0.792 1.031,0.792 1.031,0.792 0.917,1.031 false 1.167,0.708 1.333,0.865 0.167,0.156 10 *1 3.135,0.708 3.333,0.865 0.198,0.156 10 *2 0.271,0.417 0.583,0.573 0.313,0.156 10 *a 2.271,0.417 2.583,0.573 0.313,0.156 10 *b
*a Intake Side
*b Exhaust Side
*1 Gray
*2 Black


Apply a light coat of engine oil to a new oil seal.

NOTICE:

Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal to the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seal is gray and the exhaust valve oil seal is black.



b.
A150956C07
0.095,0.812 0.418,0.978 0.323,0.166 10 SST 0.581,1.279 0.749,1.445 0.168,0.166 10 *a 1.918,1.279 2.083,1.434 0.166,0.155 10 *b 0.456,0.91 0.588,0.91 0.588,0.91 1.054,0.695 false
*a CORRECT
*b INCORRECT


Using SST, push on the oil seal.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 5.INSTALL INTAKE VALVE

a.

Place the cylinder head on wooden blocks.


b.
A146314C08
2.698,1.708 2.969,2.031 0.271,0.323 10 *a
*a 30 mm (1.18 in.) or more


Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


c.

Install the intake valve, valve inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



d.
A150946E02
1.413,0.22 1.745,0.381 0.333,0.161 10 SST 1.803,0.314 1.897,0.314 1.897,0.314 1.948,0.563 false

Using SST and wooden blocks, compress the spring and install the 2 retainer locks.

SST
09202-70020  (09202-00010)


e.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.




Hide 13715 6.INSTALL EXHAUST VALVE

a.

Place the cylinder head on wooden blocks.


b.
A146315C06
2.708,1.708 3.281,2.063 0.573,0.354 10 *a
*a 30 mm (1.18 in.) or more


Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


c.

Install the exhaust valve, valve inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



d.
A150947E02
0.114,0.191 0.447,0.352 0.333,0.161 10 SST 0.505,0.284 0.598,0.284 0.598,0.284 0.649,0.533 false

Using SST and wooden blocks, compress the spring and install the 2 retainer locks.

SST
09202-70020  (09202-00010)


e.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.