Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046951 CYLINDER HEAD A

3ZR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A150967E01
0.142,0.058 0.448,0.216 0.306,0.159 10 SST 1.342,0.635 0.5,0.164 0.5,0.164 1.231,1.197 false

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head on wooden blocks.


g.
A150969C09
1.344,0.625 0.698,0.208 0.698,0.208 0.583,0.208 false 1.229,1.198 0.698,0.208 false 0.229,0.125 0.531,0.271 0.302,0.146 10 SST 3.188,1.094 3.344,1.24 0.156,0.146 10 *1
*1 Protrusion Height


Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

9.9 to 10.3 mm (0.390 to 0.406 in.)



h.
A150971

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A150968E01
1.522,1.759 1.843,1.908 0.321,0.15 10 SST 2.063,0.83 1.751,1.749 1.751,1.749 2.222,1.192 false

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard bush bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head on wooden blocks.


g.
A150970C09
2.219,1.24 1.865,1.802 1.865,1.802 1.771,1.802 false 1.938,0.531 1.677,0.365 1.677,0.365 1.604,0.365 false 0.938,1.208 1.104,1.365 0.167,0.156 10 *1 1.417,1.698 1.719,1.854 0.302,0.156 10 SST 1.25,0.281 1.552,0.427 0.302,0.146 10 SST
*1 Protrusion Height


Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

11.15 to 11.55 mm (0.439 to 0.455 in.)



h.
A150972

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE SPARK PLUG TUBE

NOTICE:

When using a new cylinder head, the spark plug tubes must be replaced.


a.
A211988C05
2.698,0.354 2.51,0.354 2.51,0.354 2.281,0.865 false 2.719,0.229 2.885,0.385 0.167,0.156 10 *1 1.625,1.708 1.802,1.865 0.177,0.156 10 *2 1.833,0.26 2,0.417 0.167,0.156 10 *3
*1 Adhesive
*2 Distance
*3 Seal Diameter


Apply adhesive onto the shaded area of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


Distance from end of tube:

1.0 to 7.0 mm (0.0394 to 0.294 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.




b.
A205906C07
2.365,3.177 2.531,3.323 0.167,0.146 10 *1
*1 Protrusion Height


Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

122 mm (4.80 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 11155A 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.
A150959C10
1.342,2.996 1.518,3.163 0.176,0.167 10 *3 1.574,3.687 1.765,3.855 0.191,0.168 10 *1 0.775,2.401 0.951,2.568 0.176,0.167 10 *2
*1 Protrusion Height
*2 Width
*3 Height


Using a plastic-faced hammer, tap in a new ring pin to the specified protrusion height.

Standard Ring Pin:
Height Width Protrusion
11.7 to 12.3 mm (0.461 to 0.484 in.) 12.0 mm (0.472 in.) 6.5 to 7.5 mm (0.256 to 0.295 in.)