Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2012.12–2013.11
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046952 CYLINDER BLOCK A

3ZR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the piston or piston ring.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


HINT:

This procedure is for type A.


a.
A253363C01
1.917,3 2.229,3.156 0.313,0.156 10 *a 1.917,3.5 2.229,3.656 0.313,0.156 10 *b 2.417,3.198 2.729,3.354 0.313,0.156 10 *c
*a 16 mm (0.630 in.)
*b 9.0 mm (0.354 in.)
*c 27 mm (1.06 in.)


Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 11432A 2.INSTALL NO. 1 TAPER SCREW PLUG

a.

Clean the No. 1 taper screw plug and plug hole.


b.

Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug. Then install the No. 1 taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Install the plug within 3 minutes of applying adhesive.

·

Do not start the engine within 1 hour of installing the plug.




Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 4.INSTALL PISTON

HINT:

Perform "Inspection After Repairs" after replacing the piston.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A151020C09
2.065,1.671 2.27,1.836 0.205,0.166 10 *1 1.126,1.221 2.15,1.648 2.15,1.648 2.15,1.23 false
*1 Service hole cutout portion


Using a screwdriver, install a new snap ring at one end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



b.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).


c.
A151021C09
1.354,0.167 1.24,0.167 1.24,0.167 0.979,0.635 true 1.417,2.354 2.302,2.813 2.302,2.813 2.771,2.771 true 2.823,2.031 2.302,2.813 true 1.417,0.094 1.625,0.26 0.208,0.167 10 *1 2.188,2.833 2.396,3 0.208,0.167 10 *1
*1 Front Mark


Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

HINT:

The piston and pin are a matched set.



d.

Using a screwdriver, install a new snap ring on the other end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


Hide 13011 5.INSTALL PISTON RING SET

HINT:

Perform "Inspection After Repairs" after replacing the piston ring.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A146333C18
1.458,1.813 1.458,1.542 false 2.094,0.26 1.906,0.26 1.906,0.26 1.771,0.469 false 0.896,0.198 1.01,0.198 1.01,0.198 1.365,0.51 true 1.427,2.875 1.49,2.99 1.49,2.99 1.552,2.875 false 0.688,0.115 0.875,0.292 0.188,0.177 10 *1 2.115,0.167 2.302,0.344 0.188,0.177 10 *2 1.344,1.823 1.531,2 0.188,0.177 10 *3 1.385,3.021 1.573,3.198 0.188,0.177 10 *4
*1 Oil Ring Expander
*2 Oil Ring
*3 Coil Joint
*4 Oil Ring End


Install the oil ring expander and oil ring by hand.

NOTICE:
·

Install the expander and oil ring so that their ring ends are at opposite sides.

·

Securely install the expander to the inner groove of the oil ring.




b.
A289030C04
1.208,2.615 1.667,2.135 1.667,2.135 1.885,2.135 true 1.083,4.26 1.083,4.427 false 2.313,4.26 2.313,4.427 false 1.75,3.531 1.521,3.542 1.521,3.542 1.146,3.219 true 2.229,0.49 2.656,0.323 false 1.375,2.615 1.979,2.427 1.979,2.427 2.198,2.427 true 1.385,3.198 1.99,3.01 1.99,3.01 2.208,3.01 true 0.344,2.948 0.698,3.292 0.354,0.344 10 *1 0.354,3.531 0.729,3.802 0.375,0.271 10 *2 1.938,2.031 2.396,2.406 0.458,0.375 10 *4 1.792,3.458 2.167,3.844 0.375,0.385 10 *5 2.229,2.354 2.552,2.625 0.323,0.271 10 *6 1.021,4.448 1.323,4.667 0.302,0.219 10 *1 2.24,4.448 2.531,4.667 0.292,0.219 10 *2 2.698,0.229 3.01,0.427 0.313,0.198 10 *3 2.25,2.948 2.573,3.219 0.323,0.271 10 *6
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Piston Ring Expander
*4 Code Mark (T) or Code Mark (T1)
*5 Code Mark (2T)
*6 Paint Mark
V100135

Upward


Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

NOTICE:
·

Install the No. 1 compression ring with the code mark (T or T1) facing upward.

·

Install the No. 2 compression ring with the code mark (2T) facing upward.

·

Paint marks can only be checked on new piston rings. When reusing piston rings, check each piston ring profile in order to install them into the correct positions.



HINT:
Item Cord Mark Paint Mark
Type A No. 1 Compression Spring T Sky Blue
No. 2 Compression Spring 2T Sky Blue
Oil Ring - White
Type B No. 1 Compression Spring T1 Yellow
No. 2 Compression Spring 2T Orange
Oil Ring - Sky Blue



c.
A289832C09
0.49,1.885 0.833,1.885 0.833,1.885 1.25,1.573 false 2.104,0.167 2.302,0.167 2.302,0.167 2.365,0.458 false 0.302,1.833 0.646,2.104 0.344,0.271 10 *1 1.927,0.115 2.354,0.49 0.427,0.375 10 *2 2.76,0.604 3.188,0.979 0.427,0.375 10 45°
*1 No. 1 Compression Ring and Oil Ring
*2 No. 2 Compression Ring and Oil Ring Expander
V100136

Engine Front


Position the piston rings so that the ring ends are as shown in the illustration.


Hide 11711 6.INSTALL CRANKSHAFT BEARING

a.
A151015C12
0.737,1.234 0.9,1.386 0.163,0.153 10 *1 0.562,2.05 0.693,2.214 0.132,0.164 10 A 0.339,2.314 0.576,1.335 0.576,1.335 0.717,1.335 false
*1 Scale


Install the upper bearing (except No. 3 journal).

i.

Install the upper bearing to the cylinder block.

HINT:

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



ii.

Using a scale, measure the distance between the cylinder block edge and the upper bearing edge.

Dimension (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.




b.
A162987C10
0.803,1.996 1.047,2.229 0.244,0.233 10 A 1.988,2.01 2.188,2.194 0.199,0.184 10 B 0.931,1.199 1.106,1.357 0.176,0.158 10 *1 0.633,2.389 0.76,1.293 0.76,1.293 0.912,1.293 false
*1 Vernier Caliper


Install the upper bearing (for No. 3 journal).

i.

Install the upper bearing to the cylinder block.

HINT:

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



ii.

Using a vernier caliper, measure the distance between the cylinder block edge and the upper bearing edge.

Dimension (A - B) or (B - A):

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:

Do not apply engine oil to the bearing or the contact surfaces.




c.

Install the lower bearing.

i.

Install the lower bearing to the bearing cap.


ii.
A151016C10
0.757,1.985 0.93,2.138 0.173,0.153 10 *2 0.725,2.911 0.861,3.074 0.136,0.163 10 A 2.054,2.911 2.19,3.074 0.136,0.163 10 B 2.537,2.071 2.723,2.236 0.186,0.166 10 *1 2.526,2.174 2.406,2.174 2.406,2.174 2.198,2.485 false
*1 Vernier Caliper
*2 Mark 1, 2, 3, 4 and 5


Using a vernier caliper, measure the distance between the bearing cap edge and lower bearing edge.

Dimension (A - B) or (B - A):

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.




Hide 11791 7.INSTALL UPPER CRANKSHAFT THRUST WASHER

a.
A150982C08
2.448,0.146 2.563,0.146 false 2.448,0.156 1.313,1.281 true 2.448,0.156 1.563,1.469 true 2.573,0.063 2.781,0.219 0.208,0.156 10 *1
*1 Oil Grooves


Install the 2 thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.


b.

Apply engine oil to the crankshaft thrust washers.


Hide 13411 8.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper bearings and install the crankshaft to the cylinder block.


b.

Apply engine oil to the lower bearings.


c.
A296528C03
0.604,2.625 1.875,3.021 1.875,3.021 3.135,2.625 false 1.26,2.635 1.875,3.021 1.875,3.021 2.469,2.625 false 1.875,3.021 1.875,2.635 false 1.813,3.063 2.073,3.26 0.26,0.198 10 *1
*1 Number Mark
V100135

Engine Front


Examine the number marks and install the bearing caps to the cylinder block.


d.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


e.
A205924

Temporarily install the 10 crankshaft bearing cap bolts.


f.
A235755C02
1.962,2.427 2.146,2.589 0.184,0.162 10 *a
*a Less than 5.0 mm (0.197 in.)


Push on the crankshaft bearing caps with your hand until the clearance between the crankshaft bearing caps and cylinder block is less than 5.0 mm (0.197 in.).


g.
A151024

Using a plastic-faced hammer, lightly tap the bearing caps to ensure a proper fit.


h.

Install the crankshaft bearing cap bolts.

NOTICE:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



i.

Step 1:

i.
A297850N02
1.698,0.385 1.854,0.583 0.156,0.198 10 1 1.719,1.792 1.875,1.99 0.156,0.198 10 2 1.021,1.75 1.177,1.948 0.156,0.198 10 3 1.042,0.417 1.198,0.615 0.156,0.198 10 4 2.427,1.74 2.583,1.938 0.156,0.198 10 5 2.406,0.427 2.563,0.625 0.156,0.198 10 6 0.448,1.677 0.604,1.875 0.156,0.198 10 7 0.469,0.469 0.625,0.667 0.156,0.198 10 8 2.948,1.698 3.104,1.896 0.156,0.198 10 9 2.948,0.49 3.177,0.667 0.229,0.177 10 10

Install and uniformly tighten the 10 crankshaft bearing cap bolts in several steps in the sequence shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



j.

Step 2:

i.

Mark the front side of the crankshaft bearing cap bolts with paint.


ii.

Tighten the bearing cap bolts 90° in the sequence shown in step 1.



k.

Check that the paint marks are now at a 90° angle to the front.


l.

Check that the crankshaft turns smoothly.


m.

Check the crankshaft thrust clearance.

Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY


Hide 13041 9.INSTALL CONNECTING ROD BEARING

a.
A151017C08
1.96,2.463 2.102,2.622 0.142,0.16 10 A 2.957,2.463 3.099,2.622 0.142,0.16 10 B 0.733,1.572 0.9,1.721 0.167,0.15 10 *1 0.721,1.66 0.571,1.66 0.571,1.66 0.355,2.61 false
*1 Vernier Caliper


Install the connecting rod bearings to the connecting rods and connecting rod caps.


b.

Using a vernier caliper, measure the distance between the edges of the connecting rods and connecting rod caps, and the connecting rod caps and connecting rod bearings.

Dimension (A - B) or (B - A):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.



Hide 10.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A289832C10
0.49,1.885 0.833,1.885 0.833,1.885 1.25,1.573 false 2.104,0.167 2.302,0.167 2.302,0.167 2.365,0.458 false 0.302,1.833 0.646,2.104 0.344,0.271 10 *1 1.927,0.115 2.354,0.49 0.427,0.375 10 *2 2.76,0.604 3.188,0.979 0.427,0.375 10 45°
*1 No. 1 Compression Ring and Oil Ring
*2 No. 2 Compression Ring and Oil Ring Expander
V100136

Engine Front


Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.


b.

Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.
A205932C02
2.167,2.781 1.917,2.781 true 1.51,3.813 1.51,3.76 1.51,3.76 1.281,3.688 false 2.146,3.708 2.229,3.708 2.229,3.708 2.417,3.906 true 1.427,3.844 1.625,4.021 0.198,0.177 10 *1 1.927,3.625 2.177,3.802 0.25,0.177 10 *1 1.656,2.708 1.896,2.896 0.24,0.188 10 *1
*1 Front Mark


Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.

NOTICE:
·

When inserting the piston with connecting rod, do not allow it to make contact with the oil nozzle.

·

Match the numbered connecting rod cap with the connecting rod.




d.
A205918C08
0.988,0.099 1.144,0.252 0.157,0.153 10 *1 1.17,0.194 1.238,0.194 1.238,0.194 1.467,0.738 false
*1 Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Install the connecting rod cap bolts.

NOTICE:

The connecting rod cap bolts should be tightened in 2 progressive steps.



g.

Step 1:

i.
A208477E01
0.534,0.117 0.838,0.268 0.304,0.151 10 SST 0.918,0.215 1.044,0.215 1.044,0.215 1.319,0.518 false

Using SST, install and alternately tighten the bolts of the connecting rod cap in several steps.

SST
09205-16011  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



h.

Step 2:

i.

Mark the front side of each connecting rod cap bolts with paint.


ii.

Tighten the cap bolts 90°.



i.

Check that the paint marks are now at 90° angle to the front.


j.

Check that the crankshaft turns smoothly.


k.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY


Hide 12211 11.INSTALL NO. 1 VENTILATION CASE

HINT:

There are 2 installation types for the No. 1 ventilation case. Depending on the installation type, the number of bolts, nuts and stud bolts used will vary.


a.
A158007C06
2.75,0.92 2.874,1.076 0.125,0.156 10 A 1.946,0.92 2.071,1.076 0.125,0.156 10 A 2.466,3.585 2.638,3.735 0.172,0.15 10 *1 0.652,2.349 0.813,2.498 0.161,0.149 10 *1 1.552,3.685 1.903,3.842 0.351,0.156 10 A - A 1.906,3.349 2.339,3.678 2.339,3.678 2.457,3.678 false 1.572,2.689 1.746,2.844 0.174,0.155 10 *a 2.115,3.037 2.285,3.184 0.17,0.147 10 *b 1.199,2.03 0.987,2.436 0.987,2.436 0.846,2.436 false
*1 Seal Packing
*a Distance from inside Edge of Cover to Center of Seal Packing
*b Seal Packing Diameter


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Seal Packing Diameter Distance from Inside Edge of Case to Center of Seal Packing
2.0 to 3.0 mm (0.0787 to 0.118 in.) 5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.

for Type A:

i.

Install the No. 1 ventilation case with the 6 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

for Type B:

i.

Install the No. 1 ventilation case with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)