Home › Engine / Hybrid System › 3ZR-FE FUEL › FUEL INJECTOR
RM3090E _51 Engine / Hybrid System _008406 3ZR-FE FUEL _0046953 FUEL INJECTOR G

3ZR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.



b.

Check the injection volume.

CAUTION:
·

Perform the inspection in a well-ventilated area.

·

Do not perform the inspection near any naked flames.



i.
A269697
1.969,1.208 1.969,1.49 false 2.938,1.229 2.938,0.719 false 0.729,1.906 0.583,1.906 0.583,1.906 0.479,1.583 false 1.052,0.302 0.927,0.302 0.927,0.302 0.729,0.927 false 2.865,1.26 3.052,1.438 0.188,0.177 10 false *1 1.885,1.531 2.073,1.708 0.188,0.177 10 false *2 1.115,0.208 1.302,0.385 0.188,0.177 10 false *4 0.771,1.833 1,2.01 0.229,0.177 10 false *3
*1 Fuel Pipe
*2 SST (Fuel Tube Connector)
*3 SST (Hose)
*4 SST (Hose Band)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.
A262995
0.583,0.25 0.75,0.25 0.75,0.25 0.99,0.427 false 0.583,0.833 0.75,0.833 0.75,0.833 0.958,0.635 false 0.583,1.583 0.75,1.583 0.75,1.583 0.969,1.417 false 2.24,0.615 2.417,0.167 2.417,0.167 2.583,0.167 false 2.594,1.323 2.75,1.583 2.75,1.583 2.917,1.583 false 2.219,1.74 2.406,2 2.406,2 2.573,2 false 0.354,0.76 0.667,0.917 0.313,0.156 10 *1 0.354,1.5 0.667,1.656 0.313,0.156 10 *2 0.354,0.177 0.667,0.333 0.313,0.156 10 *3 2.604,0.094 2.917,0.25 0.313,0.156 10 *4 2.938,1.5 3.25,1.656 0.313,0.156 10 *5 2.604,1.927 2.917,2.083 0.313,0.156 10 *6
*1 SST (Hose Band)
*2 SST (Adapter)
*3 SST (Hose)
*4 O-Ring
*5 SST (Clamp)
*6 Vinyl Tube


Install the O-ring onto the fuel injector assembly.


iii.

Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iv.
A272843
1.427,1.771 1.625,2 1.625,2 1.719,2 false 2.406,0.75 2.604,1 2.604,1 2.698,1 true 1.729,1.917 1.885,2.063 0.156,0.146 10 *1 2.708,0.917 2.865,1.063 0.156,0.146 10 *2
*1 SST (Tie Band)
*2 Lock


Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



v.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


vi.

Install a vinyl tube onto the fuel injector assembly.

NOTICE:

Install a suitable vinyl tube onto the fuel injector assembly to prevent gasoline from splashing out.



vii.

Put the injector into a graduated cylinder.



ix.
A262997
1.917,1 1.75,1 1.75,1 1.604,0.427 false 1.958,0.917 2.417,1.115 0.458,0.198 10 SST
V100135

Connect


Connect SST (EFI inspection wire H) to the fuel injector assembly and battery for 15 seconds and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30080  

Standard injection volume:

60 to 73 cc (3.7 to 4.5 cu. in.) per 15 seconds


Difference between each injector:

13 cc (0.8 cu. in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire H) is securely connected.

·

Always do the switching at the battery side.



If the injection volume is not as specified, replace the fuel injector assembly.



c.

Inspect for fuel leaks.

i.

In the condition above, disconnect the test probes of SST (EFI inspection wire H) from the battery and check the fuel leakage from the fuel injector assembly.

Standard:

1 drop or less every 12 minutes