Home › Power Source / Network › 3ZR-FE BATTERY / CHARGING › GENERATOR(for 100 A Type) › 2012.12–2013.11
RM3090E _57 Power Source / Network _008412 3ZR-FE BATTERY / CHARGING _0046987 GENERATOR A

3ZR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A282127

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator in a vise between aluminum plates.


b.
A282128
1.146,1.25 1.865,1.802 1.865,1.802 2.115,1.802 true 3.083,0.635 2,0.156 2,0.156 1.688,0.156 true 1.75,1.063 2,0.167 true 2.458,1.198 2.458,0.646 true 2.375,1.229 2.688,1.385 0.313,0.156 10 *1 1.208,0.073 1.677,0.271 0.469,0.198 10 SST A 2.146,1.719 3.219,1.917 1.073,0.198 10 SST B
*1 Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



c.
A282130
1.99,0.688 2.396,0.688 false 1.719,0.448 1.885,0.292 1.885,0.292 2.177,0.292 false 2.24,0.208 3,0.479 0.76,0.271 10 SST B 2.448,0.604 3.208,0.927 0.76,0.323 10 SST A 1.552,1.771 1.865,1.927 0.313,0.156 10 *a
*a Hold
V100135

Turn


Using a wrench to hold SST A, turn SST B counterclockwise to loosen the generator pulley with clutch.

NOTICE:

Be careful as the generator pulley with clutch or rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator.


e.

Remove the generator pulley with clutch from the rotor shaft.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator on the generator pulley with clutch.


b.
A282132

Remove the 3 bolts and generator rear end cover.


Hide 27387 4.REMOVE TERMINAL INSULATOR

a.
A282133

Remove the terminal insulator from the generator coil assembly.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A282134

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A282135

Remove the 4 bolts.


b.
A153383C13
1.114,1.723 1.409,1.879 0.295,0.156 10 SST 2.721,0.599 3.011,0.744 0.289,0.145 10 SST 0.573,0.516 0.756,0.675 0.183,0.159 10 *a 1.067,1.801 0.993,1.801 0.993,1.801 0.654,1.588 false 2.666,0.686 2.56,0.686 2.56,0.686 2.094,0.855 false
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A282149

Remove the washer.


b.
A153384

Remove the generator rotor assembly.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A282139

Check that the bearing is not rough or worn and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A108429

Remove the 4 screws and retainer plate from the generator drive end frame assembly.


b.
A282136
1.125,1.198 2.042,1.823 2.042,1.823 1.104,1.375 true 2.094,1.76 2.552,1.958 0.458,0.198 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)