Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM J

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  ECU Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, voltage from the MREL terminal of the ECM is applied to the EFI-MAIN NO. 1 relay. This causes the contacts of the EFI-MAIN NO. 1 relay to close, which supplies power to terminal +B of the TCM.

WIRING DIAGRAM

C279518E01
6.135,3.177 6.594,3.375 0.458,0.198 10 false B79 6.135,3.344 6.594,3.542 0.458,0.198 10 false TCM 5.896,2.646 6.354,2.844 0.458,0.198 10 false E1 5.896,1.031 6.354,1.229 0.458,0.198 10 false +B 5.635,1.135 6.094,1.333 0.458,0.198 10 false 18 5.708,2.75 6.167,2.948 0.458,0.198 10 false 8 4.271,2.667 4.729,2.865 0.458,0.198 10 false ECM 4.281,2.469 4.74,2.667 0.458,0.198 10 false A61 3.74,1.708 4.198,1.906 0.458,0.198 10 false 45 4,1.573 4.458,1.771 0.458,0.198 10 false MREL 2.323,1.917 3.521,2.115 1.198,0.198 10 false EFI-MAIN NO. 1 3.167,1.135 3.625,1.333 0.458,0.198 10 false 3 3.167,1.677 3.625,1.875 0.458,0.198 10 false 1 2.375,1.135 2.833,1.333 0.458,0.198 10 false 5 2.375,1.677 2.833,1.875 0.458,0.198 10 false 2 0.156,1.031 1.927,1.24 1.771,0.208 10 false from EFI-MAIN NO. 1 Fuse 0.469,3.156 4.135,3.354 3.667,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)
a.
C205632C12
1.51,0.156 1.948,0.417 0.438,0.26 1,1.708 1.188,1.125 true 0.177,0.146 0.49,0.344 0.313,0.198 10 *a 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 0.802,1.76 1.281,1.958 0.479,0.198 10 8 (E1)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B79-8 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)
a.
C205632C13
1.51,0.156 1.948,0.417 0.438,0.26 1.073,1.688 1.24,1.281 false 0.177,0.146 0.49,0.344 0.313,0.198 10 *a 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 0.885,1.76 1.365,1.958 0.479,0.198 10 18 (+B)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B79-18 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - TCM)
3.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - TCM)
a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the B79 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - B79-18 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) or B79-18 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR