Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0715  Input / Turbine Speed Sensor Circuit Malfunction  P0717  Input Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transaxle. By comparing the input turbine speed (speed sensor NT) signal with the counter gear speed (speed sensor NC) signal, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0715 Input / Turbine Speed Sensor Circuit Malfunction When the speed sensor input voltage is either higher than 1.9 V or below 0.1 V for 4.5 seconds or more (1-trip detection logic).
·

Speed sensor NT (transmission revolution sensor)

·

Transmission wire

·

TCM


Comes on DTC stored
P0717 Input Speed Sensor Circuit No Signal All conditions are met for 5 sec. or more (1-trip detection logic):
(a) Gear change is not performed.
(b) Gear position is 2nd, 3rd, 4th, 5th or 6th.
(c) Transmission input shaft speed is less than 300 rpm.
(d) Transmission output shaft speed is 1000 rpm or more.
(e) Park/neutral position switch NSW and R input signals are OFF.
·

Speed sensor NT (transmission revolution sensor)

·

Transmission wire

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The NT terminal of the TCM detects a pulse signal from speed sensor NT (input RPM). The TCM calculates gear shifts by comparing the signal from speed sensor NT with the signal from speed sensor NC.

While the vehicle is operating in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.

HINT:
·

*1: A pulse is not output or is irregularly output.

·

*2: The vehicle speed is 50 km/h (31 mph) or more.



WIRING DIAGRAM

C279413E01
2.271,4.615 4.51,4.875 2.24,0.26 10 Automatic Transaxle Assembly 3.74,4.052 5.104,4.292 1.365,0.24 10 Transmission Wire 1.177,4.052 3.469,4.281 2.292,0.229 10 Transmission Revolution Sensor 5.604,1.698 6.063,1.896 0.458,0.198 10 NTB 5.604,2.479 6.063,2.677 0.458,0.198 10 NTO 5.604,2.813 6.063,3.01 0.458,0.198 10 NCB 5.604,3.583 6.063,3.781 0.458,0.198 10 NCO 5.823,4.75 6.281,4.948 0.458,0.198 10 TCM 5.406,1.813 5.729,2.021 0.323,0.208 10 1 5.406,2.583 5.729,2.792 0.323,0.208 10 2 5.406,2.917 5.729,3.125 0.323,0.208 10 4 5.417,3.688 5.74,3.896 0.323,0.208 10 3 1.563,2.073 2.865,2.292 1.302,0.219 10 Speed Sensor NT 1.563,3.167 2.865,3.385 1.302,0.219 10 Speed Sensor NC

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed (speed sensor NT) Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from speed sensor NT equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from speed sensor NT nearly equal to engine speed


The data is displayed in increments of 50 rpm.
NT Sensor Voltage Input turbine speed sensor (speed sensor NT) output voltage Min.: 0 V
Max.: 5 V
Engine idling: 0.1 to 1.9 V -
Powertrain > ECT > Data List
Tester Display
SPD (NT)
NT Sensor Voltage
50003 64 157,378
HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR INSTALLATION
a.

Remove the transmission valve body assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL


b.
C133219

Make sure that the connector is properly connected, and check the transmission revolution sensor installation.

OK:

The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION WIRE

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR

2.INSPECT TRANSMISSION WIRE
a.
C206824C06
1.458,4.073 1.76,3.167 true 2.208,4.083 1.885,3.167 true 1.781,1.635 1.625,1.25 true 1.313,1.635 1.448,1.24 true 0.375,2.49 0.656,2.688 0.281,0.198 10 *b 0.375,0.354 0.594,0.552 0.219,0.198 10 *a 1.302,4.125 1.667,4.323 0.365,0.198 10 NTO 2.083,4.125 2.469,4.323 0.385,0.198 10 NTB 1.167,1.677 1.542,1.875 0.375,0.198 10 NTB 1.677,1.677 2.031,1.875 0.354,0.198 10 NTO 0.031,0.052 0.25,0.25 0.219,0.198 10 *1
*1 Transmission Wire
*a Transmission Revolution Sensor Side
*b TCM Side


Disconnect the transmission revolution sensor connector.


b.

Remove the TCM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NTB transmission revolution sensor side - 1 (NTB) TCM side Always Below 1 Ω
NTO transmission revolution sensor side - 2 (NTO) TCM side Always Below 1 Ω
NTB transmission revolution sensor side - Body ground Always 10 kΩ or higher
NTO transmission revolution sensor side - Body ground Always 10 kΩ or higher
NTB transmission revolution sensor side - All other terminals except 1 (NTB) TCM side Always 10 kΩ or higher
NTO transmission revolution sensor side - All other terminals except 2 (NTO) TCM side Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE SPEED SENSOR NT (TRANSMISSION REVOLUTION SENSOR)

NG

3.REPLACE SPEED SENSOR NT (TRANSMISSION REVOLUTION SENSOR)
a.

Replace the transmission revolution sensor.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK IF DTC OUTPUT RECURS (DTC P0715 OR P0717)
4.CHECK IF DTC OUTPUT RECURS (DTC P0715 OR P0717)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > ECT > Clear DTCs
50002 64


e.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P0715 or P0717 is output A
DTCs are not output B




A

B

END