Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2012.12–2015.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving in lock-up.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains on even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) pattern 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during "stop and go" driving, the TCM interprets this as a fault in the stop light switch, illuminates the MIL and stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) five times for two consecutive driving cycles in order for this DTC to be stored.

WIRING DIAGRAM

C279415
5.604,1.344 6.063,1.542 0.458,0.198 10 false STP 5.344,1.458 5.802,1.656 0.458,0.198 10 false 12 5.823,3.052 6.281,3.25 0.458,0.198 10 false B79 5.833,3.229 6.292,3.427 0.458,0.198 10 false TCM 4.833,1.458 5.292,1.656 0.458,0.198 10 false 1 4.063,1.458 4.521,1.656 0.458,0.198 10 false 2 3.938,1.688 4.396,1.885 0.458,0.198 10 false A5 3.938,1.865 5.146,2.094 1.208,0.229 10 false Stop Light Switch 3.365,1.49 3.979,1.688 0.615,0.198 10 false STOP 2.469,1.49 3.083,1.688 0.615,0.198 10 false ALT 1.188,2.094 1.99,2.323 0.802,0.229 10 false Battery 1.385,1.49 2,1.688 0.615,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
Powertrain > ECT > Data List
Tester Display
Stop Light Switch
50003 64 204


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C228781
1.146,0.833 1.594,1.125 true 2.271,1.615 1.885,1.323 true 1.125,1.625 1.542,1.323 true 2.271,0.833 1.833,1.125 true 0.719,3.083 0.865,2.135 0.865,2.135 1.073,2.135 false 1.01,1.552 1.167,1.75 0.156,0.198 10 4 2.333,0.75 2.49,0.948 0.156,0.198 10 1 2.333,1.552 2.49,1.75 0.156,0.198 10 3 1.01,0.75 1.167,0.948 0.156,0.198 10 2 0.104,0.104 0.5,0.323 0.396,0.219 10 *1 1.135,2.073 1.531,2.292 0.396,0.219 10 *2 0.281,3.604 0.594,3.802 0.313,0.198 10 *a 1.063,3.604 1.375,3.802 0.313,0.198 10 *b
*1 Stop Light Switch Assembly
*2 Pin
*a Not Pushed
*b Pushed


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - TCM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BATTERY - TCM)
a.
C205632
1.51,0.156 1.948,0.417 0.438,0.26 1.938,1.76 1.729,1.198 true 0.115,0.125 0.427,0.323 0.313,0.198 10 *a 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 1.75,1.823 2.406,2.021 0.656,0.198 10 12 (STP)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B79-12 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
B79-12 (STP) - Body ground Brake pedal released Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR