Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, this memory is cleared and the TCM determines that there is a malfunction in the power supply circuit. When the engine is next started, the TCM will illuminate the MIL and store the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage An open in the TCM back-up power source circuit is detected for 3 sec. or more (1-trip detection logic).
·

Open in back-up power source circuit

·

ECD system

·

TCM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the TCM does not store other DTCs.


WIRING DIAGRAM

C279325
5.594,1.354 6.208,1.552 0.615,0.198 10 false BATT 5.604,2.323 6.219,2.521 0.615,0.198 10 false E1 5.823,3.052 6.438,3.25 0.615,0.198 10 false B79 5.823,3.24 6.438,3.438 0.615,0.198 10 false TCM 5.417,1.458 6.031,1.656 0.615,0.198 10 false 1 5.417,2.427 6.031,2.625 0.615,0.198 10 false 8 4.146,1.49 5.042,1.698 0.896,0.208 10 false EFI NO. 3 2.875,1.49 4,1.698 1.125,0.208 10 false EFI-MAIN NO. 1 1.781,2.083 2.906,2.292 1.125,0.208 10 false Battery 2.052,1.49 2.854,1.698 0.802,0.208 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM DTC P0560)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTCs are not output A
P0560 is output (ECD system) B




A

2.CHECK TCM (POWER SOURCE, BODY GROUND)

B

2.CHECK TCM (POWER SOURCE, BODY GROUND)
a.
C205632
1.51,0.156 1.948,0.417 0.438,0.26 1.792,1.771 1.542,1.104 true 0.927,1.781 1.177,1.135 true 0.125,0.135 0.438,0.333 0.313,0.198 10 *a 1.594,0.198 1.969,0.427 0.375,0.229 10 B79 0.76,1.833 1.24,2.031 0.479,0.198 10 8 (E1) 1.552,1.833 2.208,2.031 0.656,0.198 10 1 (BATT)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B79-1 (BATT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B79-8 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - BATTERY, BODY GROUND)