Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM D

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle TCM can then be read.


b.
C201372

Euro-OBD regulations require that the vehicle on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in any of the following:

·

The emission control system/components

·

The powertrain control components (which affect vehicle emissions)

·

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the TCM memory.

If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the TCM memory.


c.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle. The scan tool displays DTCs, freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared with the scan tool.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR



M-OBD (EXCEPT EUROPEAN SPECIFICATION)


a.

When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the TCM can then be read.


b.
C201372

OBD regulations require that the vehicle on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in any of the following:

·

The emission control system/components

·

The powertrain control components (which affect vehicle emissions)

·

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the TCM memory.

If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the TCM memory.



NORMAL MODE AND CHECK MODE


The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2-trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available to technicians as an option. In check mode, 1-trip detection logic is used when reproducing malfunction symptoms for increasing the ability of the system to detect malfunctions, including intermittent malfunctions (GTS only).


2-TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the TCM memory (1st trip). If the ignition switch is turned off and then turned to ON again, and the same malfunction is detected again, the MIL illuminates.



FREEZE FRAME DATA


a.

The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not and whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E08
0.375,1.74 3.052,1.969 2.677,0.229 10 Freeze frame data which can be read 0.698,0.656 1.281,0.906 0.583,0.25 10 0.5 sec. 1.344,0.656 1.938,0.896 0.594,0.24 10 0.5 sec. 1.969,0.667 2.625,0.885 0.656,0.219 10 0.5 sec. 1.865,0.052 2.917,0.292 1.052,0.24 10 DTC is stored

The GTS displays freeze frame data recorded at five different points: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. The data can be used to reproduce the vehicle condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.



CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace the battery before proceeding.


CHECK MIL


a.

Check that the MIL illuminates when the ignition switch is turned to ON.

If the MIL does not illuminate, there is a problem in the MIL circuit.

for 2AD-FTV:

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>MIL Circuit

for 2AD-FHV:

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>MIL Circuit


b.

When the engine is started, the MIL goes off.