DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / (desired system) / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | - |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383.75 rpm |
Engine idling: 750 to 850 rpm | - |
| Calculate Load | Calculated load by ECM | Min.: 0%
Max.: 100% |
·
Engine idling: 7 to 26% ·
Running without load (2500 rpm): 10 to 20% |
- |
| Coolant Temp | Engine coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
After warming up engine: 60 to 90°C (140 to 194°F) | ·
If the value is -40°C (-40°F), the sensor circuit is open. ·
If the value is 140°C (284°F), the sensor circuit is shorted. |
| Intake Air | Intake air temperature | Min.: -40°C (-40°F)
Max.: 140°C (419°F) |
Equivalent to temperature at intake manifold | Intake air temperature received from the ECM. |
| Engine Run Time | Engine run time | Min.: 0 seconds
Max.: 65535 seconds |
Time after engine start | - |
| Battery Voltage | Battery voltage | Min.: 0 V
Max.: 65.535 V |
Engine idling: 11 to 14 V | - |
| Glow Indicator Supported | Status of the glow indicator supported | Unsupp or Supp | Supp | - |
| Glow Indicator | Status of the glow indicator | ON or OFF | - | - |
| Starter Signal | Starter signal | ON or OFF | ·
Engine cranking: ON ·
Engine not cranking: OFF |
- |
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Stop Light Switch | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Check Mode | Check mode | ON or OFF | ON: Check mode on | - |
| SPD Test Result | Check mode result for vehicle | Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor | Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor | Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor | Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor | Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor | Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor | Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor | Compl or Incmpl | - | - |
| # Codes(Include History) | # of Codes | Min.: 0
Max.: 255 |
- | Number of stored DTCs. |
| MIL | MIL status | ON or OFF | ON: MIL on | - |
| MIL ON Run Distance | MIL on run distance | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Distance after DTC stored | - |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 minutes
Max.: 65535 minutes |
Equivalent to running time after MIL turns on | - |
| Time after DTC Cleared | Time after DTC cleared | Min.: 0 minutes
Max.: 65535 minutes |
Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Equivalent to distance driven after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | Min.: 0
Max.: 255 |
Number of warm-up cycles after DTCs cleared | - |
| OBD Requirements | OBD requirements | - | - | - |
| Number of Emission DTC | Emissions-related DTCs | Min.: 0
Max.: 127 |
- | - |
| Model Code | Model code | - | - | - |
| Transmission (Engine) Type | Transmission type | - | - | - |
| Cylinder Number | Cylinder number | - | - | - |
| Transmission Type | Transmission type | - | - | - |
| Destination | Destination | - | - | - |
| Model Year | Model year | - | - | - |
| System Identification | System identification | - | - | - |
| Engine Speed from EFI | Engine speed | Min.: 0 rpm
Max.: 16383.75 rpm |
- | Engine speed received from the ECM. |
| Intake-Air Temp from EFI | Intake-air temperature from EFI | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
- | Intake air temperature received from the ECM. |
| Coolant Temp from EFI | Coolant temperature from EFI | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
- | Coolant temperature received from the ECM. |
| Accel Position from EFI | Absolute accelerator pedal position | Min.: 0%
Max.: 100% |
- | - |
| Injection Volume from EFI | Injection volume | Min.: 0 mm3/st
Max.: 640 mm3/st |
Engine idling: 4 to 12 mm3/st | Injection volume received from the ECM |
| SPD (NT) | Input turbine speed (speed sensor NT) | Min.: 0 rpm
Max.: 12750 rpm |
·
Lock-up on (after warming up the engine): Value from speed sensor NT equal to engine speed ·
Lock-up off (idling with shift lever in N): Value from speed sensor NT nearly equal to engine speed |
The data is displayed in increments of 50 rpm. |
| SPD (NC) | Counter gear speed (speed sensor NC) | Min.: 0 rpm
Max.: 12750 rpm |
Vehicle stopped: 0 km/h (0 mph) | The data is displayed in increments of 50 rpm. |
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (N,P Range) Supported | Status of PNP switch (N or P) supported | Supp or Unsupp | - | - |
| Shift SW Status (N,P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| A/T Oil Temperature 1 | ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
·
After stall test: Approx. 80°C (176°F) ·
Equal to ambient temperature after cold soak |
If the value is "-40°C (-40°F)" or "150°C (302°F)", the ATF temperature sensor circuit is open or shorted. |
| NT Sensor Voltage | Input turbine speed sensor (speed sensor NT) output voltage | Min.: 0 V
Max.: 5 V |
Engine idling: 0.1 to 1.9 V | - |
| NC Sensor Voltage | Counter gear speed sensor (speed sensor NC) output voltage | Min.: 0 V
Max.: 5 V |
Engine idling: 0.1 to 1.9 V | - |
| TPS 3 Switch | No. 3 ATF pressure switch status | ON or OFF | ·
ON: Shift solenoid valve SLU is on ·
OFF: Shift solenoid valve SLU is off |
- |
| Lock Up | Lock-up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Lock Up Solenoid Status | Shift solenoid valve SL status | ON or OFF | ·
ON: Shift solenoid valve SL operating ·
OFF: Shift solenoid valve SL not operating |
- |
| Shift Status | TCM gearshift command | 1st, 2nd, 3rd, 4th, 5th or 6th | Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid valve SLT status | ON or OFF | ·
OFF: Accelerator pedal depressed ·
ON: Accelerator pedal released |
- |
| SLU Solenoid Status | Shift solenoid valve SLU status | ON or OFF | ·
ON: Shift solenoid valve SLU operating ·
OFF: Shift solenoid valve SLU not operating |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Pattern Switch (PWR/M) | Sport mode status | ON or OFF | ·
ON: Sport mode on ·
OFF: Sport mode off |
- |
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) ·
ON: "+" shift paddle operated and held (up-shift)* ·
OFF: "+" shift paddle not operated (up-shift)* |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) ·
ON: "-" shift paddle operated and held (down-shift)* ·
OFF: "-" shift paddle not operated (down-shift)* |
- |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
*: w/ Shift Paddle Switch
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. |
| Activate the Solenoid (SLU) | Operate shift solenoid valve SLU | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SLT) | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
Vehicle stopped ·
Engine idling |
| Activate the Lock Up | Control shift solenoid valve SLU and SL to set the automatic transaxle to lock-up | ON or OFF | Can be used to check shift solenoid valve SLU and SL operation.
[Vehicle Condition] Vehicle speed: 60 km/h (37 mph) or more |
| Activate the Solenoid (SL) | Operate shift solenoid valve SL | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Control the Shift Position | Operate the shift solenoid valves and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Can be used to check the operation of the shift solenoid valves.
A 10-second interval is required between gear changes. Do not down-shift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (30 mph) or less |
| Activate the Solenoid (SL1) | Operate shift solenoid valve SL1 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operate shift solenoid valve SL2 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL3) | Operate shift solenoid valve SL3 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL4) | Operate shift solenoid valve SL4 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
Activate the Solenoid (SLT) in the Active Test is performed to confirm that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST
Note that the pressure readings for the Active Test and Hydraulic Test are different.