Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2012.12–2015.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM J

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Shift Paddle Switch Circuit  


DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM

C279484E01
2.01,4.354 2.823,4.708 0.813,0.354 10 No. 1 Switch Wire 4.281,4.344 5.188,4.698 0.906,0.354 10 Spiral Cable Sub-assembly 2.885,4.354 4,4.698 1.115,0.344 10 Steering Pad Switch Assembly 6.271,1.458 6.75,1.677 0.479,0.219 10 SFTU 6.271,3.333 6.75,3.552 0.479,0.219 10 SFTD 5.917,1.458 6.396,1.677 0.479,0.219 10 B76 5.917,3.354 6.396,3.573 0.479,0.219 10 A61 5.958,3.135 6.438,3.354 0.479,0.219 10 28 5.958,1.24 6.438,1.458 0.479,0.219 10 61 5.135,1.458 5.615,1.677 0.479,0.219 10 G8 5.135,1.24 5.615,1.458 0.479,0.219 10 14 5.135,3.344 5.615,3.563 0.479,0.219 10 G8 5.135,4.042 5.615,4.26 0.479,0.219 10 G8 5.188,3.135 5.667,3.354 0.479,0.219 10 7 5.188,3.823 5.667,4.042 0.479,0.219 10 2 4.708,1.344 5.188,1.563 0.479,0.219 10 SUP 4.708,3.24 5.188,3.458 0.479,0.219 10 SDN 4.708,3.927 5.188,4.146 0.479,0.219 10 ECC 4.052,1.458 4.531,1.677 0.479,0.219 10 z1 4.052,3.354 4.531,3.573 0.479,0.219 10 z1 4.052,4.031 4.531,4.25 0.479,0.219 10 z1 3.625,1.344 4.104,1.563 0.479,0.219 10 SUP 3.625,3.24 4.104,3.458 0.479,0.219 10 SDN 3.615,3.927 4.094,4.146 0.479,0.219 10 ECC 4.094,1.24 4.573,1.458 0.479,0.219 10 6 4.042,3.135 4.521,3.354 0.479,0.219 10 12 4.094,3.823 4.573,4.042 0.479,0.219 10 7 2.5,1.344 2.979,1.563 0.479,0.219 10 SFTU 2.5,3.24 2.979,3.458 0.479,0.219 10 SFTD 2.563,3.927 3.042,4.146 0.479,0.219 10 ECC 2.01,1.344 2.49,1.563 0.479,0.219 10 SFTU 2,1.698 2.479,1.917 0.479,0.219 10 ECC1 1.552,1.344 2.031,1.563 0.479,0.219 10 SFTU 1.552,1.698 2.031,1.917 0.479,0.219 10 ECC1 2.01,3.583 2.49,3.802 0.479,0.219 10 ECC1 2.01,3.24 2.49,3.458 0.479,0.219 10 SFTD 1.552,3.24 2.031,3.458 0.479,0.219 10 SFTD 1.552,3.583 2.031,3.802 0.479,0.219 10 ECC1 2.01,3.927 2.49,4.146 0.479,0.219 10 ECC 1.615,3.927 2.094,4.146 0.479,0.219 10 ECC 2.531,0.302 4.865,0.542 2.333,0.24 10 to Transmission Control Switch 6.469,6.052 6.948,6.271 0.479,0.219 10 ECM 3.167,6.052 3.646,6.271 0.479,0.219 10 TCM 0.479,6.208 2.646,6.5 2.167,0.292 10 : CAN Communication Line 0.313,2.083 1.75,2.625 1.438,0.542 10 Shift Paddle Switch RH (Transmission Shift Switch Assembly) 0.323,4.344 1.74,4.885 1.417,0.542 10 Shift Paddle Switch LH (Transmission Shift Switch Assembly)

CAUTION / NOTICE / HINT

CAUTION:

Refer to the SRS precaution before troubleshooting.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the GTS.

for LHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)
a.
C216021C01
0.354,0.99 0.719,1.219 0.365,0.229 0.781,0.458 1.354,1.042 true 0.438,1.031 0.75,1.229 0.313,0.198 10 false G8 0.448,0.375 0.906,0.573 0.458,0.198 10 false ECC 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

C279692C01
4.729,1.24 5.052,1.479 0.323,0.24 0.604,1.49 0.927,1.729 0.323,0.24 1.75,2.052 1.479,1.917 true 0.958,2.042 1.281,1.917 true 1.281,1.385 0.958,1.198 true 5.281,1.271 5.052,0.896 true 5.281,1.51 5.063,1.75 true 5.833,1.51 6.031,1.76 true 2.75,0.469 3.063,0.667 0.313,0.198 10 *1 1.792,2 2.25,2.198 0.458,0.198 10 SUP 4.75,0.813 5.208,1.01 0.458,0.198 10 SUP 0.656,2 1.115,2.198 0.458,0.198 10 SDN 4.76,1.698 5.219,1.896 0.458,0.198 10 SDN 0.646,1.104 1.104,1.302 0.458,0.198 10 ECC 6.073,1.698 6.531,1.896 0.458,0.198 10 ECC 0.667,1.521 1.125,1.719 0.458,0.198 10 G8 4.823,1.271 5.281,1.469 0.458,0.198 10 z1
*1 Spiral Cable Sub-assembly - -


b.

Measure the resistance according to the value(s) in the table below.

i.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise and measure the resistance. Then rotate the spiral cable 2.5 times counterclockwise and measure the resistance.


ii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-14 (SUP) - z1-6 (SUP) Always Below 1 Ω
G8-7 (SDN) - z1-12 (SDN) Always Below 1 Ω
G8-2 (ECC) - z1-7 (ECC) Always Below 1 Ω
G8-14 (SUP) or z1-6 (SUP) - All other terminals Always 10 kΩ or higher
G8-7 (SDN) or z1-12 (SDN) - All other terminals Always 10 kΩ or higher
G8-2 (ECC) or z1-7 (ECC) - All other terminals Always 10 kΩ or higher


NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.




Result:
Proceed to
OK
NG



OK

3.INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

NG

3.INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)
a.
C279489C01
3.063,1.469 2.76,1.042 true 2.583,1.448 2.615,1.042 true 2.083,1.448 2.5,1.042 true 2.906,1.51 3.354,1.708 0.448,0.198 10 SFTD 2.448,1.51 2.896,1.708 0.448,0.198 10 ECC 1.958,1.51 2.406,1.708 0.448,0.198 10 ECC1 0.104,0.104 0.417,0.302 0.313,0.198 10 *1
*1 Shift Paddle Switch LH
(Transmission Shift Switch Assembly)


Remove the shift paddle switch LH.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC1 "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTD - ECC1 "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

NG

REPLACE SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

4.INSPECT SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)
a.
C279490C01
2.208,1.281 2.438,0.833 true 2.781,1.281 2.563,0.833 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.021,1.323 2.646,1.521 0.625,0.198 10 SFTU 2.667,1.323 3.292,1.521 0.625,0.198 10 ECC1
*1 Shift Paddle Switch RH
(Transmission Shift Switch Assembly)


Remove the shift paddle switch RH.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTU - ECC1 "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTU - ECC1 "+" shift paddle not operated (up-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 SWITCH WIRE

NG

REPLACE SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

5.INSPECT NO. 1 SWITCH WIRE
a.
C279491C01
1.792,1.135 2.24,0.938 true 1.792,1.344 2.219,1.552 true 1.635,1.135 1.146,0.948 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 0.76,0.854 1.375,1.052 0.615,0.198 10 SFTU 2.302,0.854 2.917,1.052 0.615,0.198 10 SFTD 2.292,1.49 2.906,1.688 0.615,0.198 10 ECC
*a No. 1 Switch Wire (Steering Pad Switch Side)


Disconnect the No. 1 switch wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
SFTU - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SFTU - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.
C200879C02
0.385,0.885 0.823,1.146 0.438,0.26 2.073,1.083 2.448,0.823 true 2.073,1.396 2.438,1.542 true 1.333,1.396 1,1.552 true 0.542,0.938 0.917,1.167 0.375,0.229 10 z1 0.125,0.104 0.438,0.302 0.313,0.198 10 *a 0.688,1.469 1.104,1.667 0.417,0.198 10 ECC 2.49,0.74 2.906,0.938 0.417,0.198 10 SUP 2.49,1.469 2.906,1.667 0.417,0.198 10 SDN
*a Steering Pad Switch Assembly Connector (to Spiral Cable Sub-assembly)


Disconnect the steering pad switch assembly connector.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z1-6 (SUP) - z1-7 (ECC) "+" shift paddle operated and held (up-shift) Below 2.5 Ω
z1-12 (SDN) - z1-7 (ECC) "-" shift paddle operated and held (down-shift) Below 2.5 Ω
z1-6 (SUP) - z1-7 (ECC) "+" shift paddle not operated (up-shift) 1 MΩ or higher
z1-12 (SDN) - z1-7 (ECC) "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

7.INSPECT HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)
a.
C200874C05
1.5,2.438 1.938,2.698 0.438,0.26 1.49,0.323 1.927,0.583 0.438,0.26 2.313,1.885 2.146,1.146 true 1.875,3.99 1.708,3.25 true 1.583,2.49 1.958,2.719 0.375,0.229 10 B76 1.583,0.385 1.958,0.615 0.375,0.229 10 A61 0.135,0.104 0.417,0.302 0.281,0.198 10 *a 2.042,1.927 2.844,2.146 0.802,0.219 10 28 (SFTD) 1.625,4.031 2.521,4.26 0.896,0.229 10 61 (SFTU)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-61 (SFTU) - Body ground "+" shift paddle operated and held (up-shift) Below 2.5 Ω
A61-28 (SFTD) - Body ground "-" shift paddle operated and held (down-shift) Below 2.5 Ω
B76-61 (SFTU) - Body ground "+" shift paddle not operated (up-shift) 1 MΩ or higher
A61-28 (SFTD) - Body ground "-" shift paddle not operated (down-shift) 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR