Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047091 AUTOMATIC TRANSAXLE ASSEMBLY A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

If automatic transmission parts are replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

Hide 32101A 1.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

A202319

a.

Remove the 2 bolts and oil pan insulator.


b.
A297509N01
0.969,0.75 1.417,0.229 1.417,0.229 1.677,0.229 true 1.688,1.802 1.792,1.354 1.792,1.354 2.052,1.354 true 0.896,1.01 1.552,0.667 1.552,0.667 1.813,0.667 true 1.719,0.115 2.177,0.313 0.458,0.198 10 SST 1.854,0.563 2.313,0.76 0.458,0.198 10 SST 2.083,1.24 2.542,1.438 0.458,0.198 10 SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


c.
C207575

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 28100 3.REMOVE STARTER ASSEMBLY

Hide 4.DISCONNECT WIRE HARNESS

a.

Detach the 7 wire harness clamps.

C278989


b.

Disconnect the park/neutral position switch connector and TCM connector.

HINT:

Detach the claw, turn the lock lever, and then disconnect the TCM connector.



c.

Remove the bolt and disconnect the wire harness from the automatic transaxle assembly.


Hide 5.REMOVE GROUND CABLE

C278987

a.

Detach the clamp.


b.

Remove the bolt and ground cable from the automatic transaxle assembly.


Hide 35123A 6.REMOVE BREATHER TUBE BRACKET

a.
C209327

Disconnect the breather plug hose.


b.

Remove the bolt and breather tube bracket from the front engine mounting bracket.


Hide 12311A 7.REMOVE FRONT ENGINE MOUNTING BRACKET

C209328

a.

Remove the 4 bolts and front engine mounting bracket from the automatic transaxle assembly.


Hide 12321A 8.REMOVE REAR ENGINE MOUNTING BRACKET

A224434

a.

Remove the 4 bolts and rear engine mounting bracket from the automatic transaxle assembly.


Hide 12325A 9.REMOVE ENGINE MOUNTING BRACKET LH

C278991

a.

Remove the bolt and wire harness clamp bracket.


b.

Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.


Hide 17361J 10.REMOVE NO. 1 AIR TUBE ASSEMBLY

a.

Loosen the hose clamp, and remove the 2 bolts and No. 1 air tube from the automatic transaxle assembly.

C279462


b.

Remove the bolt and air tube support.


Hide 11.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the bolt and wire harness clamp bracket.

C278988


Hide 33823 12.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C278990

a.

Remove the 2 bolts and transmission control cable bracket from the automatic transaxle assembly.


Hide 33403M 13.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

C209335

a.

Remove the bolt and speedometer driven hole cover sub-assembly from automatic transaxle assembly.


b.

Remove the O-ring from the speedometer driven hole cover sub-assembly.


Hide 15.REMOVE STIFFENER PLATE LH AND RH

a.
C207576

Remove the 8 bolts and stiffener plate LH and RH.


Hide 30500 16.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C209716

Remove the 5 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 17.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 36100 18.REMOVE TRANSFER ASSEMBLY

Hide 36100A 19.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

C287928


a.

Remove the 2 transfer and transaxle setting stud bolts.

HINT:

It is not necessary to remove the transfer and transaxle setting stud bolts unless they are being replaced.