Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

DTC B1249 is stored when communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1249 Double Locking ECU Communication Stop No communication from the double lock door control relay assembly for more than 10 seconds.
·

Double lock door control relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Instrument panel junction block assembly



WIRING DIAGRAM

B339147E02
4.365,3.51 5.24,3.729 0.875,0.219 10 from Battery 4.375,3.938 5.281,4.156 0.906,0.219 10 from Battery 0.885,2.385 3.802,2.635 2.917,0.25 10 Main Body ECU (Multiplex Network Body ECU) 0.906,2.208 1.063,2.406 0.156,0.198 10 A 3.052,1.49 4.698,1.917 1.646,0.427 10 Instrument Panel Junction Block Assembly 0.938,5.052 3.667,5.313 2.729,0.26 10 Double Lock Door Control Relay Assembly 0.938,4.875 1.24,5.094 0.302,0.219 10 G66 0.708,5.448 2.396,5.698 1.688,0.25 10 : LIN Communication Line 2.458,4.375 2.885,4.563 0.427,0.188 10 MPX1 2.938,4.219 3.125,4.417 0.188,0.198 10 9 2.635,3.521 2.948,3.719 0.313,0.198 10 +B 2.938,3.396 3.094,3.594 0.156,0.198 10 1 2.479,3.979 3.094,4.177 0.615,0.198 10 CPUB 2.948,3.844 3.104,4.042 0.156,0.198 10 7 1.885,4.333 2.344,4.531 0.458,0.198 10 GND 1.615,4.24 1.927,4.438 0.313,0.198 10 14 2.521,0.906 3.135,1.104 0.615,0.198 10 LIN2 2.917,0.781 3.229,0.979 0.313,0.198 10 16 3.042,1.333 3.354,1.531 0.313,0.198 10 3D 4.938,0.76 5.25,0.958 0.313,0.198 10 54 3.25,3.677 4.063,3.896 0.813,0.219 10 D/L BACK 3.198,4.135 4.073,4.344 0.875,0.208 10 ECU-B NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:

When the communication between the double lock door control relay and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B1249 is output
DTC B1249 is not output



DTC B1249 is output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

DTC B1249 is not output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Disconnect the G66 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - G66-9 (MPX1) Always Below 1 Ω
A-16 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
E179554C02
1.469,0.427 1.896,0.677 0.427,0.25 1.01,1.24 0.667,1.5 false 1.01,1.521 0.896,1.781 false 2.365,1.51 2.5,1.792 false 0.094,0.042 0.333,0.229 0.24,0.188 10 *a 1.542,0.469 1.917,0.656 0.375,0.188 10 G66 0.406,1.5 0.667,1.688 0.26,0.188 10 +B 0.667,1.844 1.125,2.031 0.458,0.188 10 CPUB 2.385,1.844 2.844,2.031 0.458,0.188 10 GND
*a Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)


Disconnect the G66 double lock door control relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G66-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G66-1 (+B) - Body ground Always 11 to 14 V
G66-7 (CPUB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Temporarily replace the double lock door control relay assembly with a new or normally functioning one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RELAY>REMOVAL



Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B1249 is not output
DTC B1249 is output (for LHD)
DTC B1249 is output (for RHD)



DTC B1249 is not output

END (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY IS DEFECTIVE)

DTC B1249 is output (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

DTC B1249 is output (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the G66 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-54 - G66-9 (MPX1) Always Below 1 Ω
3D-54 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR