Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2789 No Response from ID BOX No communication between the certification ECU and ID code box for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B339675E02
0.729,1.427 2.531,1.875 1.802,0.448 10 Certification ECU (Smart Key ECU Assembly) 0.719,1.25 1.177,1.448 0.458,0.198 10 G84 1.823,0.771 2.281,0.969 0.458,0.198 10 LIN 5.115,0.76 5.573,0.958 0.458,0.198 10 LIN1 0.646,3.427 2.375,3.656 1.729,0.229 10 : LIN Communication Line 4.75,3.031 6.323,3.396 1.573,0.365 10 ID Code Box (Immobiliser Code ECU) 4.74,2.854 5.198,3.052 0.458,0.198 10 G44 2.094,0.625 2.406,0.823 0.313,0.198 10 17 4.917,0.625 5.073,0.823 0.156,0.198 10 2 4.917,1.625 5.094,1.844 0.177,0.219 10 1 5.083,1.74 5.396,1.938 0.313,0.198 10 +B 5.083,2.354 5.542,2.552 0.458,0.198 10 GND 4.927,2.24 5.083,2.438 0.156,0.198 10 5 2.802,1.729 3.677,1.99 0.875,0.26 10 from Battery 3.896,1.938 4.75,2.188 0.854,0.25 10 ECU-B NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU), refer to the entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION



HINT:

When the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2789 is output
DTC B2789 is not output



DTC B2789 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY - ID CODE BOX [IMMOBILISER CODE ECU])

DTC B2789 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY - ID CODE BOX [IMMOBILISER CODE ECU])
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G44 ID code box (immobiliser code ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-17 (LIN) - G44-2 (LIN1) Always Below 1 Ω
G84-17 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - BATTERY AND BODY GROUND)
a.
B301231C02
1.51,0.24 1.896,0.51 0.385,0.271 0.771,1.563 1.219,1.344 false 2.771,1.583 2.198,1.365 false 0.083,0.063 0.396,0.26 0.313,0.198 10 *a 0.5,1.5 0.813,1.698 0.313,0.198 10 +B 2.844,1.521 3.302,1.719 0.458,0.198 10 GND 1.573,0.292 2.031,0.49 0.458,0.198 10 G44
*a Front view of wire harness connector
(to ID Code Box [Immobiliser Code ECU])


Disconnect the ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G44-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G44-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new or normally functioning one.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2789 is not output
DTC B2789 is output



DTC B2789 is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] IS DEFECTIVE)

DTC B2789 is output

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)